XTEMOS ELEMENT
AJAX PRODUCTS TABS
Cam Analysis Apparatus
The apparatus is designed to study the cam profiles and performance of cam and follower system. The apparatus consists of a shaft supported by ball bearings upon which three different types of cams can be mounted.
The push rod for follower is supported vertically, which can adopt three different types of followers. Cams and followers can be changed easily. A variable speed motor rotates the cam. A dial gauge permits plotting of follower displacement with respect to cam position. By operating the system at different Speeds, jump speed can be found and also the effect of weight and spring force on jump speed can be studied. Jump can be visualized also with the help of stroboscope (it is not supplied With the product).
SPECIFICATIONS OF CAM ANALYSIS APPARATUS:
1.Cam -Eccentric, tangent and circular ARC type – one each. 2.Follower- mushroom, flat faced and roller type – one each. 3.Cams and followers are hardened to reduce wear of the surfaces. 4.Variable speed motor coupled to camshaft of suitable range and Variac. 5.A dial gauge to note the follower displacement. 6.A technical manual accompanies the equipment.SERVICES REQUIRE FOR CAM ANALYSIS APPARATUS:
1.230 V, A.C. stabilized supply along with earthing connection. 2.Bench area 0.5m x 0.5m x 0.5m height. 3.Tachometer to measure the jumping speed, (can be supplied extra)
Forceps (Different Types)
Worcester Circuit Board
Description
Enables students to investigate nature and properties of electricity by using simple circuits which are easily constructed on a base board. The connector system uses P.C.B. strips with cut-out sections whose ends can easily be inserted in spring terminals, ensuring low contact resistance and ease of connection. The kit consists of : 1. Baseboard, plastic, with spring terminals and three battery holders. (1) 2. Batteries. (3) 3. Lamps 1.25 V MES. (10) 4. Lamp holders mounted on PCB connectors. (6) 5. Plain connector PCBs. (10) 6. Wire wound potentiometer with crocodile clip connections. (1) 7. Silicon diode. (1) 8. Resistor 3.9 ohm 2.5 W (1) 9. Pair Leads, red, with crocodile clip at each end. (1) 10. Pair Leads, black, with crocodile clip at each end (1) 11. Pair Leads, yellow, with crocodile clips at each end. (1) 12. Switches mounted on PCB. connectors (2) 13. PVC rod 15 cm long (1) 14. Soft iron nails, 5 cm long (2) 15. Bare copper wire, swg 20 (2 m) 16. Bare eureka wire, swg 34 (2 m) 17. Plastic covered copper wire (2 m) 18. Electrode support (1) 19. Pencil lead electrodes (10) 20. Sheet copper foil, 150 mm square (1) 21. Pack Steel wool (1) 22. Instruction manual in English. (1)
SAFETY GOOGLES
PRODUCT DESCRIPTION
- Economical goggle offers indirect venting and anti-fog coating for reduced fogging
- Polycarbonate lens absorbs 99.9 percent UV
- Meets the high impact requirements of ANSI Z87.1-2010 Standard
- Sturdy polycarbonate lens wide opening to fit over prescription eyewear
- Protective splash goggle clear lens
XTEMOS ELEMENT
AJAX PRODUCTS TABS SIMPLE
Newton’s Color Disc
Description
To demonstrate the discovery made by Newton that white light is composed of seven colors. Consisting of a pulley mounted on a metal stand, the seven colored disc is driven by gears connected to a hand driven wheel. When the colored disc rotates, the eye can’t distinguish between individual colors and perceive it as white color.
4 Stroke 4 Cylinder Diesel Engine
4 Stroke 4 Cylinder Diesel Engine – Motor Driven Actual Cut Section Working Model With Valve Timing Attachment
The engine be sectioned to show the internal constructional details.The working of individual part and accessories like Valves,Pistons,pumps,Crank and Camshaft,etc.will be demonstrated.It is provided with Flyweel and it is mounted on a sturdy iron frame. This actual cut section engine helps the student to understand about the parts and the working of the engine very easily. It is specially made dissectible for demonstration purposes.The actual cut section engine will be supplied with key card & very interesting literature regarding working.
Force Table
To verify the law of composition and resolution of forces consisting of a aluminium table 40cm in dia.
its raised rim has a engine divided scale, graduated in 360° mounted on heavy vertical support rod & tripod base provided with leveling screws.
Body under study in a ring in center of the table fastened by cords passing over four pulleys attached with the table.
Complete with four pulleys, four weights hangers twelve weights (2x10gm, 2x20gm, 4x50gm, 4x100 gm.)
Conical Measures
The Conical Measures offered by us are very effectively for measuring small quantities of reagents.
Moulded in Polypropylene, these autoclavable measures have a hexagonal base, which provides it excellent stability.
The measures are clear, have good chemical resistance, and have raised graduation for easy.
Material : Polypropylene
| Particulars | Pack (Pcs) | |
|---|---|---|
| Conical Measure 12 ml | 12 | |
| Conical Measure 25 ml | 12 | |
| Conical Measure 50 ml | 12 | |
| Conical Measure 125 ml | 12 | |
| Conical Measure 200 ml | 12 |
XTEMOS ELEMENT
AJAX PRODUCTS TABS ALTERNATIVE
Fashion
Galvano Meter
Optical Set For Ray Track Apparatus
Description
Comprises a white painted wooden board mounted on nonskid plastic feet, and a removable turntable about 170 mm in diameter. Two orthogonal lines along the turntables diameter divide it into four equal quadrants Just beyond the rim of the turntable, a circular scale graduated 90 – 0 – 90 – 0 – 90 °, with 1° subdivision, Also includes a ray box with a 12 V, 24 W bulb Supplied complete with a cylindrical convex lens with focal length approx. 75 mm and two double slits, giving one wide beam slit and one each of single, triple and five slits An optical set is available separately, comprising of one each of rectangular, semi-circular, right-angled triangular – 90 ° 45 ° 45° trapezoidal, biconvex and biconcave prisms.
ANALYTICAL BALANCE
DESCRIPTION
- Student Physical Balances with flat beam.
- Chemical Balances with Flat beam and rider using facility.
- Chainomatic Analytical Balances with external alteration of weights up to 100 mg.
- Analytical Balances with Triangular beam with rider using facility / Flat beam with vernier scale.
- Capacity 1mg to 100gms
- Capacity 1mg to 200gms
- IDDC Certified & Tested, 100gm
- Capacity 1mg to 500gm
- 1gm
- 2gm
- 5gm
- 10gm
- 20gm
- 50gm
- 100gm
- 200gm
XTEMOS ELEMENT
AJAX PRODUCTS TABS ARROWS PAGINATION
Internally Expanding Mechanical Drum Brake System
Hydraulic Ram Test Setup
DESCRIPTION:
The Set-up is designed to study the Hydraulic Ram. Hydraulic RAM is used for pump little quantity of water to high head from a large quantity of water available at low head. It works on a principle of water hammer stating that “When flowing water is suddenly stopped in a long pipe a pressure wave travels along the pipe creating an effect of water hammer”. The Set-up consists of a pipe section fitted with a pulse valve and non-return valve, a supply reservoir on a stand which is connected to an overhead tank, an air vessel above the valve chamber smoothes cyclic fluctuations from the Ram delivery. Different pressure may be applied to the pulse valve to change the closing pressure and hence the operating characteristic. The flow rate of useful and waste water is measured using measuring tank and stop watch provided. Pressure and Vacuum Gauge are connected on delivery and suction side for the purpose of measurement.EXPERIMENT:
Ø To find out discharge of useful water and waste water. Ø To find out the efficiency of the Hydraulic RAMFEATURES:
Ø Closed loop water circulation Ø Compact & stand alone set-up Ø MS Excel sample calculation program on demand Ø Stainless Steel tanks and wetted parts Ø Superb painted structure Ø Simple to Operate & MaintainUTILITIES REQUIRED:
Electric Supply: – Provide 230 +/- 10 VAC, 50 Hz, Single Phase Electric Supply with proper earthing. (Neutral – Earth voltage less than 5 VAC) 5 A, three pin socket with switch for pump. Water Supply: Tap water connection ½ “ BSP Distilled water @ 90 Ltrs. (Optional)TECHNICAL SPECIFICATIONS:
Ø Product : Hydraulic RAM Ø RAM : Size 50 x 15 mm, Supply Head 2.5m, Delivery Head 10 m (max.) Ø Air Vessel : Suitable Capacity MOC SS Ø Delivery Line : For RAM, Dia 50 mm Length 6 m. Ø Pump : Capacity 1 HP, Crompton / Sharp / Hero make Ø Supply Tank : Capacity 150 Ltrs. Ø Overhead Tank : Capacity 100 Ltrs. Ø Measuring Tank : Suitable Capacity one each for useful and waste MOC SS fitted (2 Nos.) with Piezometer Tube & Scale Ø Piping : GI / PVC Ø Stop Watch : Electronic Ø Pressure Gauge : Bourdon Type Ø Control Panel : Comprises of Standard make On/Off Switch, Mains Indicator etc. Ø Tanks will be made of Stainless Steel. Ø The whole Set-up is well designed and arranged in a good quality painted structure.
Emissivity Measurement Apparatus
The apparatus consists of a test plate and a comparator. A black plate is used as a comparator for test plate. When all the physical, dimensions and the temperatures are equal, heat losses from both plates will also be the same, except radiation losses. Hence the input difference will be due to difference in emissive. Both the plates are kept in a panel enclose with perplex front and are given inputs through separate dimmerstats so that temperatures of both can be kept equal. Thus emissivity can determine over a wide range of temperatures.
SPECIFICATIONS:
1.Test plate and Black plates — 160mm. Dia. Aluminum plates, mounted in Panel with mica heater inside. 2.Instrumental panel consisting of- a)Voltmeter and ammeter for input measurement to both heaters through a selector switch. b)Separate dimmers for both the plates. c)Multichannel digital temperature indicator. A technical manual accompanies the unit.SERVICES REQUIRED:
1.Space area of 1.5m x 1 m. at working height. 2.230v, 15A, AC supply with earthing connectionXTEMOS ELEMENT
AJAX PRODUCTS TABS WITH ICONS
Smart Energy Meter
A Smart Energy Meter based on Analog Devices IC has been developed to build an Advanced Metering Infrastructure (AMI). The AMI system facilitates networking capability via GSM, ZigBee and ModBus. A Smart Energy Meter Development system has been developed by us, which consists of 1φ/3φ measurement section, a 32-bit ARM controller, wireless modules and powerful software. The student can completely understand the concept and usage of this trainer. This can be also used as one of the IOT server node.
Features
• 3 Phase energy readings displayed in the Graphics LCD • Simple design, Efficient and Highly Accurate • Easy connectivity for various loads • Keys to change the settings • Supports GSM, ZigBee and ModBus for networking • LPC2148 based processing board • 32/16 bit ARM7TDMI-S CPU with 60MHz maximum CPU clock • On board peripherals for extension • Graphics LCD interfaced to display the energy readings • Keys for various settings • Current Sensors and Voltage Sensors provided to measure 3 phase voltages and currents • Polyphase energy metering IC provides highly accurate energy measurement • Energy metering IC interfaced via I2C with Controller module • CC2530 Controller with maximum 32MHz CPU clock • High-speed and low-power 8051 CPU • 2.5GHz IEEE 802.15.4 compliant RF transceiver upto 250kbps data rate • UART Connectivity to interface with CPU
Rules Steel
TDS Meter
CNC Lathe Trainer With Servo Drives
CONTROLLER:
(1) Type of control system: PLC based system (2) Main Spindle Drive : AC Motor with VFD (3) Z and X Drives : Stepper drive with RAMP function (4) Input to Stepper Motor : Optically Isolated (5) Motor Drive :TTL Compatible (6) Run Speed Control : Computer controlled through software (7) Interpolation : Liner / Circular / Parabolic (8) Cycles Used :G,M,S,T,F,I,K,M,F (9) Cycles : Circular Interpolation / Canned (10) Threading : Straight / Taper (11) Power Devices : Short Circuits and over Temperature Protected (12) Real Time Tool Path Simulation : ProvidedMACHINE DETAILS:
(1) Center height : 100mm (2) Swing over Carriage : 80mm (3) Distance between Centre : 250mm (4) Longitudinal Travel : 250mm (5) Weight : 350 kg (6) Dimension in mm : 1100 x 750 x 1700 (7) Rapid Travel : 500mm/min (8) Resolution X & Z Axis : 10micron (9) Dt. Motor Power : 40V – 4A (10) Lubrication : ManualSPINDLE:
(1) Spindle Speed : Continuous Variable (2) Spindle Power : 2 HP (3) Inside Taper : MT3 (4) Speed Range : 50 to 3000RPMXTEMOS ELEMENT
AJAX PRODUCTS TABS LOAD MORE PAGINATION
SILICA CRUCIBLE WITHOUT LID
PRODUCT DESCRIPTION
- Crucible is glazed inside and outside.
- Highly resistant to alkalis and hot temperatures
- 50ml capacity
- Outside diameter 55mm, 42mm height
- No lid includedSilica crucible is glazed inside and outside. Highly resistant to alkalis and hot temperature SIZES ARE: 15ML 25ML 50ML 80ML 100ML 150ML
SILICA CRUCIBLE TALL FORM Without Lid, Translucent
XTEMOS ELEMENT
AJAX PRODUCTS TABS CAROUSEL
Mini Rotary Shaker
Body made out of thick mild steel finished with powder coating.
PMDC motor used for shaking.
Platform size 300x300 mm. S.S. platform consists of 9x250ml conical flask lotus type clamps.
RPM range 50-250 RPM, Electronic variable control, with 0-60 min mechanical timer.
Mini Rotary Shaker
Workable on 220 V AC 50Hz single phase.
Optional
Digital R.P.M. indicator Digital timer (0-99 min.)
Protozoa
Description
All Charts are made on PVC rexine , hand drawn, waterproof, in fast multi colors with a black background. Each chart is provided with rollers to hang on wall. Size 75×100 cm. Amoeba structure & locomotion Plasmodium (Malarial Parasite), stages of development Paramecium structure Paramecium Reproduction Euglena structure & Life History Entomoeba Histolytica – structure & L.H.
Carboys
Carboys, made of polypropylene, are much lighter than glass.
These autoclavable, dependable & durable Carboys are provided with wide handles making it convenient while carrying or pouring purposes.
We also offer carboy with stopcock for the esteemed clients.
Material : Polypropylene
| Particulars | Pack (Pcs) | |
|---|---|---|
| Carboy 10 ltrs. | 1 | |
| Carboy 20 ltrs. | 1 | |
| Carboy With Stop Cock 10 ltrs. | 1 | |
| Carboy With Stop Cock 20 ltrs. | 1 |
