XTEMOS ELEMENT
AJAX PRODUCTS TABS
Test Tube PEG Rack
We bring forth supreme Test Tube PEG Rack for our clients.
Our range of Test Tube PEG Rack has been highly appreciated for its quality.
These can conveniently hold inverted tubes for drying purpose and minimizes collections of airborne contaminants inside the tube.
This rack can also be used to hold and dry electrophoresis and chromatography plates.
Material : Polypropylene
| Particulars | Pack (Pcs) | |
|---|---|---|
| Test Tube Peg Rack-96 Places for 13mm Tubes | 6 | |
| Test Tube Peg Rack-50 Places for 16mm Tubes | 6 |
Two Stroke Diesel Engine Model
Microcontroller Based Differential Relay
This test set-up consists of a. Microcontroller based differential relay. b. 300VA transformer set-up
Specification
• One PIC Microcontroller used as processor to read all current, (PY, SY) & activation of relay function • One LCD to indicate, - Set value, All currents - Set time, DMT/IDMT type - Relay tripping time. - Biased/Unbiased type status • Four numbers of key used - To select IDMT/DMT type or biased un-biased type - Set current value adjustment - Set time adjustment - Reset function • Six 5A CT used to sense primary and secondary current. • One 12V TPTT auxiliary relay used for contactor operation. • Specification: - Current input : 0-5Amp - Voltage input : 0-230V - Number of contact : Three number No contact @ 220V, 10Amp rating. - Auxiliary supply : 230VAC, 50Hz • PC interfacing facility power ON/OFF switch with indicator. • Make : VI MICRO • Model : VPL - 83A
Angel Sum Property of Quadrilateral
XTEMOS ELEMENT
AJAX PRODUCTS TABS SIMPLE
Bending Moment & Shear Force Apparatus
INTRODUCTION:
Shear Forces occurs when two parallel forces act out of alignment with each other. For example, in a large boiler made from sections of sheet metal plate riveted together, there is an equal and opposite force exerted on the rivets, owing to the expansion and contraction of the plates. Bending Moments are rotational forces within the beam that cause bending. At any point within a beam, the Bending Moment is the sum of: each external force multiplied by the distance that is perpendicular to the direction of the force.EXPERIMENT MANUAL:
1. To verify the Shear force a cross-section of the beam. 2. To verify the bending moment in cross–section of beam with a flexure condition.APPARTUS SPECIFICATION:
1. Dimensions : 158 cm X 45cm X (h)60cm 2. Total Beam Length : 160 cm with flexure 3. Width of Beam : 5 cm 4. Distance of Length in between : 5 cm 5. Height of beam : 36 mm 6. No. of Hanger for weights : 3 7. No. of Spring Balance : 2 (of 10kg) 8. Total Weight of Apparatus : 13.1 kgACCESSORY REQUIRES:
1. Shear force apparatus 2. Bending Moment Apparatus 3. Hangers 4. Weights 5. Two Spring balances – 10kgs
SPECIMEN JAR WITH BAKELITE COVER, ‘S.G.’
Oxygen And Carbon Cycle In Nature
Advanced Universal FPGA Trainer
The universal FPGA trainer consist of a main board with many peripheral like USB Device, Ethernet, Serial ports, Parallel Port, VGA port, Graphics LCD, Switches, LED, ADC etc. This motherboard has 4Nos of high speed connectors for plugging the daughter boards, which contains the FPGA of any manufacturers. Separately 2Nos of 100 pin high speed connectors provided for hardware expansion as plug in boards.
• Industry standard interconnection
- 10 MBPS Ethernet
- USB 2.0 Interface
- Two RS232 ports
- 9 pin D connector
• Memory Sub system
- 8 MB x 16 Bit SDRAM
- 4MB x 16 bit flash EEPROM
- 256KB I2C EEPROM
• Additional Features
- One 240 x 128 graphics LCD
- 16 Nos of dip switches
- 16 discrete LEDs
- 4 digit multiplexed 7 segment LED display
- 4 x 4 matrix keyboard
- One VGA Port at 15 pin D connector
- One PS2 connector for keyboard and mouse
- Reset Switch
- I2C Real time Clock
• Analog Input & Output
- 2MSPS SPI ADC (12 Channel)
- Temperature sensor interface
- One 16 bit Stereo CODEC
• 2 Nos. of 100 pin high speed connectors provided to hardware expansion can be used as hardware bus.
• Multilayer board for superior signal integrity.
• 54 I/O pins terminated at 3Nos of 20 pin connector for external interfacing.
XTEMOS ELEMENT
AJAX PRODUCTS TABS ALTERNATIVE
Fashion
Generation Of Involute Gear Tooth Profile
This board illustrates the process of cutting of involutes Gear Teeth, by use of rack type cutter It consists of 3 white acrylic discs A, B, C. having pitch circle diameter 450 mm, 300 mm & 200 mm respectively. A gear tooth profile with module 25mm can be traced out on a peace of paper placed between disc and cutter. An affect of Interference and Undercutting on correct profile of gear tooth can be studied from the profiles traced.
Human Eye, 3 Times Enlarged
Wooden Pipette Stand, Holds 24 pipettes Vertically
XTEMOS ELEMENT
AJAX PRODUCTS TABS ARROWS PAGINATION
Worm Sector Type Steering System
Worm & Sector Type Steering System – Actual Working
The working of steering system is shown with the help of actual parts assembled on square iron pipe frame. All the necessary parts of steering system are shown in actual working form. This model helps the student to understand the working of the steering system very easily. It is specially made dissectible for demonstration purposes.
Cylinderical Magnet
Smart LED Lighting module
Zigbee offers Green and Global Advanced Wireless Technology, Connecting the widest range of Devices to work together intelligently and help you to control your real world. CC2530 is the first System On chip, which has integrated 8051Microcontroller with ZigBee RF transceiver. A WSN based Smart LED lighting module has been developed with latest LED controller from MICREL, 10 LEDs, ZigBee RF module using CC2531 for Wireless Control with onboard Light Sensor. WSN based LED lighting module has a Base Board and a Zigbee RF module. Zigbee RF module can be plugged into the connector provided on the Base Board, meant for further upgradation.
Features
• 10 Nos. of LED of 2watt each • 400 milliwatts LED • Constant current driver for LED control • Connectors for plug-in Zigbee RF module • Remote ON/OFF control by Zigbee RF Control • On board light intensity sensor • LED Brightness control either by program or by Light Sensor input.XTEMOS ELEMENT
AJAX PRODUCTS TABS WITH ICONS
Instrument Tray
Acquire from us comprehensive range of Instrument Tray which is well reckoned for its quality.
This Instrument Tray has cover which fits into groove of trays to minimize spillage of material.
Smaller size can be used to sterilize small instruments whereas the larger size allows pipettes to be fully immersed in disinfectant prior to sterilizing.
Material : Polypropylene
| Particulars | Pack (Pcs) | |
|---|---|---|
| Instrument Tray 220 x 150 x 70 mm | 2 | |
| Instrument Tray 450 x 150 x 70 mm | 2 |
Transmission Line Trainer
This trainer is designed for study of co-oxial cable characteristics like Impedance measurement, VSWR measurement etc., It is based, i) The latest technology of DDS Based RF source. ii) Directional coupler for VSWR Measurement. iii) TDR to measure the cable fault.
Specification
• DDS RF Source - Frequency: 10 to 400MHz. - Step Size: 1KHz. - Direct Digital Synthesis (DDS) Method Based. - Since DDS Device is primarily digital, it offers. • Display: Graphics LCD display of 240x128 pixels with backlight to plot VSWR, TDR characteristics etc., • One directional coupler provided for VSWR, Return loss measurement. • In-Built RF Detector for 10-400MHz Frequency range. • In-Built TDR (Time Domain Reflectometer) to measure and study nature of discontinuation in the co-axial cable. • Output Impedance: 50 ohms. • Co-axial cable: Various lengths of 50 ohm, 75 ohm cables supplied. • All relevant waveforms are displayed graphically in the Graphics LCD
Gd Skin Color Advanced Trauma Simulator
Description
Features:
Washing, disinfection, hemostasia, enswathement etc. Open fracture, truncation trauma.Features of Advance trauma manikin:
Facial burn: I, II, IIIdegree. Laceration in forehead. The wound in jaw. Opened clavicular fracture and contusion wound on the chest. The wound in abdomen with small intension evisceration. Opened humerous fracture of right upper arm. Opened fracture of right hand (including parenchyma laceration, fracture and bone tissue exposure) Gun wound in the right palm. Opened fracture of right thighbone. Compound femur fracture of left thigh. Metal pricking wound in right thigh. Opened tibia fracture of right leg. Opened fracture of right foot with truncating trauma on small phalanx. Burns in left forearm: I, II, III degree. Truncating trauma on left thigh. Closed tibia fracture of right leg and contusion wounds in left ankle and foot.
Spectroscope
Description
Hand held simplest form of spectroscope. It can be used to get a general idea of the correlation between wavelength and observed color. A diffraction grating is used which spreads the incident light into its component wavelengths. An illuminated reference scale against which the spectrum may be viewed is also provided. Spectroscope (Wooden)XTEMOS ELEMENT
AJAX PRODUCTS TABS LOAD MORE PAGINATION
SILICA CRUCIBLE WITHOUT LID
PRODUCT DESCRIPTION
- Crucible is glazed inside and outside.
- Highly resistant to alkalis and hot temperatures
- 50ml capacity
- Outside diameter 55mm, 42mm height
- No lid includedSilica crucible is glazed inside and outside. Highly resistant to alkalis and hot temperature SIZES ARE: 15ML 25ML 50ML 80ML 100ML 150ML
SILICA CRUCIBLE TALL FORM Without Lid, Translucent
XTEMOS ELEMENT
AJAX PRODUCTS TABS CAROUSEL
Rocks Collection
Description
A comprehensive collection of igneous , metamorphic and sedimentary rocks, in wooden box with partitioned tray containing 50 specimens, each nominally numbered and enclosed in a transparent plastics bag. Specimens may be removed from bags for detailed examination. Each specimen is labelled also on the inside of the box lid, indicating the geological name.
Ticker Tape Timer 12V
Ticker Tape Timer 12V
These devices use an electromagnet which activates a striker, producing dots via a carbon disk on the ticker tape.
With 4mm terminal sockets.
The dots are produced at a rate of 50 - 60Hz depending on the mains frequency.
There are 6V and 12v units available.
The Ticker Tape Timers are used in the measurement of velocity, acceleration and general timing.
Numerical System
This panel is used to demonstrate the number systems such as binary, decimal and hexadecimal numbers. Toggle switches used to activate the displays showing the particular number entered. Input may be entered either as decimal or binary numbers with a toggle switch for mode selection. Decimal numbers are shown on a three digit seven segment LED display. 12 V / 2 A DC adaptor is required to operate it.
Comparative Terrain Model
Description
Set of 2 landform models, each includes an overlay representing ancient mountain forms that can be removed and compared with the base model to show changes millions of years later. Cross section shows basic mountain types, volcanic fault block, glaciated domes and folded mountains with lesson plan, size 45 x 60 cm.
89C51 Microcontroller Trainer
Specification
• Core :NXP89C51RD2 / 8051 • Internal Memory :64KB Flash, 1KB RAM • External Memory :64KB EPROM, 64KB RAM • 16 Digital Outputs - SMD LED Interface. • 16 Digital Inputs - Switch Interface. • 20X4 Character LCD Interface. • I2C Peripherals : - 8 Bit ADC [8-Bit 4 Channel ADC, Two Potentiometer Provide in on board]. - 8 Bit DAC. • Six 7-Segments Display Interface. • On Board Stepper Motor Driver is provided. • PWM lines are terminated at Terminal Block. • IBM PC Keyboard Interface for entering program. • CPU Lines are terminated at 50 pin Expansion Header.(VBMB and VPIC) • I/O ports terminated to connect to external devices. • Program / Execution switch is provided for serial ISP (Using ISP Utility Software). • ADC, DAC lines are terminated at terminal blocks.
Ripple Tank
Description :-
Transparent acrylic plastic ripple tank, supported in a sturdy plastic frame which has recesses to hold four legs with leveling feet.
The tank edges are shaped to minimize undesired reflections.
Tank has a drain hole closed by a rubber stopper.
With two light alloy uprights to carry a horizontal rippler support rod which is adjustable for height.
The ripple assembly, elastically suspended from the support rod, consists of a 4 – 6 V DC motor mounted on a wooden beam.
The motor has an eccentric weight which causes the beam to oscillate.
Two point sources are provided by two plastic spheres, each mounted on a right angle rod.
A metal rod is fixed centrally into a socket in one short side of the frame to afford support to the illuminant.
Overall size of the tank 580 x 500 x 80 mm, window area 370 x 280 mm, height of tank above bench level (with legs attached) approx. 375 mm.
Complete with following accessories :-
1. Two straight obstacles of aluminium alloy length 130 mm.
2. One straight obstacle length 40 mm.
3. One curved reflector radius 200 mm.
4. One trapezoidal plastic plate for refraction.
5. One wood hand wave roller.
6. One water dropper.
7. One pkt. rubber bands.
8. One foam plastic sponge.
9.One illuminant with a 12 V, 24 W lamp mounted in a lamp house and provided with a long supporting rod.
