XTEMOS ELEMENT
AJAX PRODUCTS TABS
Tube Sedimentator
Multi Tank System
Panel Features
• Rocker switch is provided to ON/OFF the process plant. • Digital Panel Meter. • Pump Indicator. • Short Circuit protection. • Mimic diagram in the panel. • All the electrical connectors are terminated in the panel.Features
• This equipment consists of four tank system, conical tank system and spherical tank system. • Four numbers of Acrylic tank are provided for doing multivariable control of four tank system. • Conical tank (SS) is provided to performing the nonlinerar control system. • Spherical tank (SS) is provided for controlling the complex system. • Six numbers of level transmitter (DPT) are provided to measures the level of the each tank. • Three numbers of smart control valve with positioner are provided in the inlet of Flow rate. • Hand valve is provided at the bottom of the process tank to study the load disturbance. • Three numbers of hand valve are provided to control the Rotameter flow rate. • Three numbers of centrifugal pump are provided for water circulation. • Two flow transmitters are mounted for conducting flow, cascade and Ratio control. • Appropriate Digital panel meters are provided to measure the transmitter and actuator signals. • Delay coils are provided to the input of the process tanks for transportation lag study. • Storage tank of 100 litre capacity (SS). • Rotameter for Visual indication of the flow rate. • Relay circuit is provided to ON/OFF the solenoid valve. • Built in regulated power supply. • All Water flow lines are connected by (SS) fittings. • Necessary patch chords are provided for interfacing the Electrical signal. • Established successful design that mimics a real industrial process. • Front panel includes mimic diagram of the process, so students can clearly see what they are controlling. • Safe, practical and realistic. • Hand valves are provided to study the coupling (Interaction) and decoupling
Worcester Circuit Board
Description
Enables students to investigate nature and properties of electricity by using simple circuits which are easily constructed on a base board. The connector system uses P.C.B. strips with cut-out sections whose ends can easily be inserted in spring terminals, ensuring low contact resistance and ease of connection. The kit consists of : 1. Baseboard, plastic, with spring terminals and three battery holders. (1) 2. Batteries. (3) 3. Lamps 1.25 V MES. (10) 4. Lamp holders mounted on PCB connectors. (6) 5. Plain connector PCBs. (10) 6. Wire wound potentiometer with crocodile clip connections. (1) 7. Silicon diode. (1) 8. Resistor 3.9 ohm 2.5 W (1) 9. Pair Leads, red, with crocodile clip at each end. (1) 10. Pair Leads, black, with crocodile clip at each end (1) 11. Pair Leads, yellow, with crocodile clips at each end. (1) 12. Switches mounted on PCB. connectors (2) 13. PVC rod 15 cm long (1) 14. Soft iron nails, 5 cm long (2) 15. Bare copper wire, swg 20 (2 m) 16. Bare eureka wire, swg 34 (2 m) 17. Plastic covered copper wire (2 m) 18. Electrode support (1) 19. Pencil lead electrodes (10) 20. Sheet copper foil, 150 mm square (1) 21. Pack Steel wool (1) 22. Instruction manual in English. (1)
Air Conditioning Trainer Window Type
Window air conditioner is becoming now a day’s necessity. The unit demonstrates the application of window air conditioner & evaluation of its performance. It consists of a small room to which a small air conditioner is connected the room is provided with a transparent front cover with a heater inside to simulate heat load in the room. Various measurements are provided so that performance of system that is COP of system, actual & theoretical cooling capacity of system & power consumption of unit with different load conditions.
SPECIFICATIONS:
1.Compressor – Hermetically sealed, Kirloskar make, having the capacity of 1/10 ton of refrigeration using R-12 refrigerant to keep room temperature between 20 to 30 c. 2.Condenser – Finned tube type, with forced air flow over the tubes, 3.Capillary tube of matched length as expansion device. 4.Evaporator – Finned tube type with forced air flow, 5.Room – 0.6 X 0.7 X 0.7 m. height, provided with transparent front wall. A heater with input control is provided inside the room. Which simulates different load conditions. 6.Measurements and Controls a) H.P. / L.P. Pressure gauges b) Digital temperature indicator to measure the temperatures at various points. c) Energy meters to measure input to compressor & heater. d) High and low pressure cutout. e) Thermostat to put off the compressor at set room temperature. f) Necessary switch for electrical components.SERVICES REQUIRED:
1.Floor area of 2m X 1 m. 2.230V, 15AC stabilized supply with earthing connectionXTEMOS ELEMENT
AJAX PRODUCTS TABS SIMPLE
Smart LED Lighting module
Zigbee offers Green and Global Advanced Wireless Technology, Connecting the widest range of Devices to work together intelligently and help you to control your real world. CC2530 is the first System On chip, which has integrated 8051Microcontroller with ZigBee RF transceiver. A WSN based Smart LED lighting module has been developed with latest LED controller from MICREL, 10 LEDs, ZigBee RF module using CC2531 for Wireless Control with onboard Light Sensor. WSN based LED lighting module has a Base Board and a Zigbee RF module. Zigbee RF module can be plugged into the connector provided on the Base Board, meant for further upgradation.
Features
• 10 Nos. of LED of 2watt each • 400 milliwatts LED • Constant current driver for LED control • Connectors for plug-in Zigbee RF module • Remote ON/OFF control by Zigbee RF Control • On board light intensity sensor • LED Brightness control either by program or by Light Sensor input.
Pteridophyta
| Azolla Sporocarp VS | Adiantum Rhizome TS |
| Adiantum Root TS | Adiantum Sorus VS |
| Equisetum Prothallus WM | Equisetum Root TS |
| Equisetum Rhizome TS | Equisetum Stem TS |
| Equisetum Cone TS | Equisetum Cone LS |
| Fern Rhizome TS | Fern (Pteris) Prothallus Young |
| Fern Prothallus with Antheridia | Fern Prothallus with Archegonia |
| Fern Prothallus with Sporophyte | Fern Leaf with Sori TS |
| Fern Sori WM | Fern Prothallus TS |
| Fern Rachis TS | Fern Root TS |
| Lycopodium Root TS Lycopodium Stem TS | Lycopodium Apex LS |
| Lycopodium Cone LS | Lycopodium Cernum Stem TS |
| Lycopodium Wightiatum Stem TS | Lycopodium Phlegmaria Stem TS |
| Marsilea Leaf TS | Marsilea Root TS |
| Marsilea Rhizome TS | Marsilea Petiole TS |
| Marsilea Sporocarp LS | Marsilea Sporocarp TS |
| Selagineela Root TS | Selaginella Rhizophore TS |
| Selaginella Leaf TS | Selaginella Stem TS |
| Selagineela Strobilus WM | Selaginella Strobillus LS |
| Selaginella Microsporangia WM | Selaginella Mega and Microsporangia WM, TS |
Aids Virus
Description
HIV virus model is enlarged millions of times, shows the outer lipid membrane with protein structures and the internal nucleus which contains the viral hereditary matter [RNA]. The nucleus is removable and condoms can be put underneath to provide a message regarding measures to be taken for protecting against HIV infections. Supplied without condoms on stand with key card.
XTEMOS ELEMENT
AJAX PRODUCTS TABS ALTERNATIVE
Fashion
Frequency Modulation And Demodulation
This Instrument is design to demonstrate the method to transmit signals via. Electromagnetic transmission and to study the Frequency Modulation and Demodulation. Whole instrument is placed in plastic moulded box and 2 mm banana plug leads are provided for modulation and demodulation connections.
Technical Specification:-
1. Fixed Output DC Regulated Power Supply of ±12 V.
2. Built in Modulating signal Generator of 2 KHz and 4 KHz selectable with a toggle switch with Amplitude to 3V peak to peak approximately.
3. Circuit diagrams for Modulator and Demodulator are printed on the milky white top panel
Pin Fin Appatatus
The apparatus consists of a channel in which the pin fin is tested in both natural as well as forced convection. The channel is connected to the suction of blower. The blower is operated to touch the pin fin in forced convection only. In natural convection, the window above the pin fin is kept open to the atmosphere. Five thermocouple tapings are given along the length of the fin. Thus the temperature distribution along the length can be distinguished. Also natural and forced heat transfer co-efficient, effectiveness, etc. can be found out.
Specifications:
1.Three pin fins- a) M. S. b) Brass c) Al 2.Channel- 150mm x 100mm x 1000mm 3.Blower – run by f.h.p. motor. 4.Orifice meter along with water manometer to measure airflow. 5.Voltmeter and ammeter to measure power input. 6.Cr- Al thermocouple with 6 tapings along with temperature indicator. 7.Dimmerstat to control power input. 8.A band heater to heat the pin fin. A technical manual accompanies the unit.Services required:
1.220v, stabilized single phase supply along with earthing Connection. 2.Floor area 2m x 1m x 1m height.
Wire helix (Slinky)
XTEMOS ELEMENT
AJAX PRODUCTS TABS ARROWS PAGINATION
Pulley Rod Mounting
Rocks And Minerals Collection
Platinum Resistance Thermometer
XTEMOS ELEMENT
AJAX PRODUCTS TABS WITH ICONS
Analytical Funnel
Our exclusive Analytical Funnel is designed specifically for analytical chemistry; the body of the Analytical Funnel is 60".
Moulded in polypropylene, these Analytical Funnel is provided with internal & external ribs to prevent air blockage.
We offer our Analytical Funnel at market leading prices.
Material : Polypropylene
| Particulars | Pack (Pcs) | |
|---|---|---|
| Analytical Funnel 35 mm | 72 | |
| Analytical Funnel 50 mm | 72 | |
| Analytical Funnel 62 mm | 36 | |
| Analytical Funnel 75 mm | 36 | |
| Analytical Funnel 100 mm | 36 |
Plant Structure II – Gymnosperms, Ferns, Mosses & Liverworts
Set of 17 Slides, comprising
Dryopteris, TS pinnule with sori
Dryopteris, TS Rachis
Dryopteris, TS rhizome
Funaria, LS of capsule
Lycopodium, TS Stem
Marchantia, VS thallus
Moss, LS antheridial Head
Moss, Leaf WM Pinus, TS young root
Pinus, LS male cone with microscopers
Pinus, LS whole female cone
Pinus, Pollen
Pinus, stem macerated
Pinus, TS leaf
Pinus, TS old stem
Polytrichum, TS stem
Integer Counters
Worcester Circuit Board
Description
Enables students to investigate nature and properties of electricity by using simple circuits which are easily constructed on a base board. The connector system uses P.C.B. strips with cut-out sections whose ends can easily be inserted in spring terminals, ensuring low contact resistance and ease of connection. The kit consists of : 1. Baseboard, plastic, with spring terminals and three battery holders. (1) 2. Batteries. (3) 3. Lamps 1.25 V MES. (10) 4. Lamp holders mounted on PCB connectors. (6) 5. Plain connector PCBs. (10) 6. Wire wound potentiometer with crocodile clip connections. (1) 7. Silicon diode. (1) 8. Resistor 3.9 ohm 2.5 W (1) 9. Pair Leads, red, with crocodile clip at each end. (1) 10. Pair Leads, black, with crocodile clip at each end (1) 11. Pair Leads, yellow, with crocodile clips at each end. (1) 12. Switches mounted on PCB. connectors (2) 13. PVC rod 15 cm long (1) 14. Soft iron nails, 5 cm long (2) 15. Bare copper wire, swg 20 (2 m) 16. Bare eureka wire, swg 34 (2 m) 17. Plastic covered copper wire (2 m) 18. Electrode support (1) 19. Pencil lead electrodes (10) 20. Sheet copper foil, 150 mm square (1) 21. Pack Steel wool (1) 22. Instruction manual in English. (1)XTEMOS ELEMENT
AJAX PRODUCTS TABS LOAD MORE PAGINATION
SILICA CRUCIBLE WITHOUT LID
PRODUCT DESCRIPTION
- Crucible is glazed inside and outside.
- Highly resistant to alkalis and hot temperatures
- 50ml capacity
- Outside diameter 55mm, 42mm height
- No lid includedSilica crucible is glazed inside and outside. Highly resistant to alkalis and hot temperature SIZES ARE: 15ML 25ML 50ML 80ML 100ML 150ML
SILICA CRUCIBLE TALL FORM Without Lid, Translucent
XTEMOS ELEMENT
AJAX PRODUCTS TABS CAROUSEL
Siemens IoT 2040 Gateway Based IoT Development System
SIMATIC IoT 2040 is an Industrial IoT Gateway, reliable open platform for collecting, Processing and transmission data. It helps the students to get the industrial IoT experience and develop Industry 4.0 Projects rapidly.
Specification:
• IoT 2040 Gateway - PLC and sensors of many brands can be integrated through Ethernet & Serial ports. - Open Protocols: Modbus, Profinet, REST or MQTT, AMQP, OPC UA - Based on Intel Quark X1020 ,(x86)@400MHz - Compatible With Open Source Software Arduino IDE and Yocto Linux - High level language support : Java, Python, C/C++ - 1 GB RAM, 8MB Flash ,256KB SRAM - Micro SD card Slot up to 32GB - One miniPCIe Slot for hardware expansion for WLAN/Additional Ethernet Port - Arduino Uno – R3 Compatible - Intel Wi-Fi + Bluetooth Module for 300MB data rate - 2xRS232/422/485(Switchable) - 1xUSB Controller + 1 x Device - 2 x 10 /100 Mbps Ethernet RJ45 • 5 types of sensors such as Temperaturesensor, LDR sensor, Motion sensor, Humidity sensor, Magnetic sensor included to • interface with IoT2040 & add on modules of IoT2040 • The IoT 2040 Gateway can communicate with PLC, DCS using profinet or OPC UA. • Analog Inputs are terminated in a SP7 patch connector • 4Nos of Digital Input SPDT Switch • 4Nos of user LEDs
MCT Box
MCT Boxes are moulded in polycarbonate and are therefore strong as well as autoclavable.
One size can hold 64 MCTs of 1.5 ml. & the other can hold 100 MXT's of 0.5 ml.
These MCT Boxes are designed to work at temperatures ranging from -190'C to + 121" C.
The transparent cover provides a good view of the contents inside & is numbered for better inventory control.
| Particulars | Pack (Pcs) | |
|---|---|---|
| MCT Box (Rack for 100 MCTs of 0.5 ml) | 4 | |
| MCT Box (Rack for 64 MCTs of 1.5 ml) | 4 |
Human Physiology Charts
Description
Poly art Charts are multi colored, accurate in details, printed on plastic, laminated on both sides, washable, non-tearable and long lasting with plastic rollers, size 75 x 100 cm. Skeletal System Muscular system Circulatory system Nervous system Digestive system Teeth & skin Human eye, ear & head Lymphatic system Respiratory system Endocrine system Nutrition Immune system Human Nose Human Heart Excretory system Human Eye Human Ear Human Kidney Human Lungs Human Liver
Laser Distance meter Lite
Description
Base Model for all basic measurements. It is small, robust base model for modern measurements. Reliable, accurate, precise and easy-to-use. We are among the prestigious industry players, engaged in offering Laser Distance Meter to our valuable customers. The offered meters are designed in strict compliance with the industry standards and are highly appreciated by the customers. These meters are accurate and are regarded for their compact size and.
Dead Weight Pressure Gauge Tester
DESCRIPTION:-
Dead weight Pressure Gauge Tester is manufactured to measure the Pressure gauge up to the capacity of 25kg/cm2.The system is nickled chrome to protect from rust. The weights are Zink Iron for long term use.EXPERIMENTS:-
• Study of the hydrostatic force on a plane surface under different submerged conditionsFEATURES:-
• Superb Painted structure • Simple to operate & maintainUTILITIES REQUIRED:-
• Machine Oil.SPECIFICATION:-
• Bourdon tube pressure gauge as manometer • Manometer with transparent scale • Manufactured from corrosion resistant materials • Components arranged on base plate. • Set of weights • Medium for transmitting pressure: hydraulic
