XTEMOS ELEMENT
AJAX PRODUCTS TABS
Worcester Circuit Board
Description
Enables students to investigate nature and properties of electricity by using simple circuits which are easily constructed on a base board. The connector system uses P.C.B. strips with cut-out sections whose ends can easily be inserted in spring terminals, ensuring low contact resistance and ease of connection. The kit consists of : 1. Baseboard, plastic, with spring terminals and three battery holders. (1) 2. Batteries. (3) 3. Lamps 1.25 V MES. (10) 4. Lamp holders mounted on PCB connectors. (6) 5. Plain connector PCBs. (10) 6. Wire wound potentiometer with crocodile clip connections. (1) 7. Silicon diode. (1) 8. Resistor 3.9 ohm 2.5 W (1) 9. Pair Leads, red, with crocodile clip at each end. (1) 10. Pair Leads, black, with crocodile clip at each end (1) 11. Pair Leads, yellow, with crocodile clips at each end. (1) 12. Switches mounted on PCB. connectors (2) 13. PVC rod 15 cm long (1) 14. Soft iron nails, 5 cm long (2) 15. Bare copper wire, swg 20 (2 m) 16. Bare eureka wire, swg 34 (2 m) 17. Plastic covered copper wire (2 m) 18. Electrode support (1) 19. Pencil lead electrodes (10) 20. Sheet copper foil, 150 mm square (1) 21. Pack Steel wool (1) 22. Instruction manual in English. (1)
Sieve Shaker (Gyratory Motion)
Ensuring durability during performance, this machine is made of mild steel and cast iron and comes with one Lid and a Pan.
This unit is used with up to 7 sieves of 150mm or 200mm (8 Inch) sieves and up to 6 sieves of 300 mm (12 Inch).
Heavy duty motor (1/4 HP) ensures the whole performance through a reduction gear immersed in oil.
Along with featuring gyratory motion, this units also performs upward and downward movement ensuring that each "square cm" of the sieve is fully utilized.
This Gyratory Sieve Machine also supplied with a pair of rods and a holder which ensures tight grip of sieve set from the top.
| Product: | Gyratory Sieve Shaker | |
| Capacity: | 7 sieves of 150mm, 6 sieves of 300mm | |
| Design: | Table Top | |
| Construction: | Cast Iron, Painted Mild steel | |
| Motor: | ¼ HP | |
| Timer: | 0 - 60 Minutes | |
| Timer Type: | Digital / Analog | |
| Power Supply: | 220 Volts |
Pipes, Resonance Demonstration
XTEMOS ELEMENT
AJAX PRODUCTS TABS SIMPLE
Sliding Mesh Gear Box
Sliding Mesh Gear Box – Actual Cut Section
The working of gear box is shown with the help of actual parts assembled on square iron pipe frame. All the necessary parts of gear box are shown in actual working form. This model helps the student to understand the working of the gear box very easily. It is specially made dissectible for demonstration purposes.
Tablet Coating Pan
Product Description
We offer coating pan that is designed to perfection and fabricated from best grades of raw material procured from reliable sources. These coating pan are suitable for coating tablets and is checked by our quality controllers for high performance and uniform coating all over the tablet. The different parts of our coating pan machines are listed as under:PAN
The coating pan is SS semi ellipsoidal size pan with a circular mouth for charging & discharging of tablets, Pan mounted at an inclination of 45 degrees to the horizontal.DRIVE ASSEMBLYPAN
The tablet coating pan consists of a suitable HP 3 Phase, 440 V, 1440 RPM TEFC motor with suitable worm reduction gear box and cone pulley arrangement to give three speed output.HOT AIR BLOWERPAN
The tablet coating pan unit is provided with a hot air blower consisting of suitable HP 3 Phase 440 V, 2880 RPM TEFC electric motor & centrifugal blower with damper delivering required CFM. The air is heated by means of suitable electric heater to give air at 30 to 90 degrees Heater with thermostat control and flexible hose pipe.
Autoclave, Radial Locking
Specification
Double wall chamber Autoclave. The inner chamber and outer wall made of stainless steel, ring made of stainless steel/ mild steel. The lid is made of stainless steel tightened by radial arms through a steering wheel made of chrome plated mild steel. The instrument is absolutely leak proof. Equipped with pressure gauze, safety valve, double safety valve, steam release valve, rubber gasket, inner container, S.S bucket and mild steel legs for Autoclave. The Autoclave can hold the in between 5psi to 20 psi. Autoclave, Vertical, Double Walled, Radial Locking.| Capacity (Lt.) | Size | |
|---|---|---|
| 23 litres | (10” x 18”) | |
| 40 litres | (12” x 22”) | |
| 52 litres | (14” x 22”) | |
| 60 litres | (14” x 25”) | |
| 75 litres | (16” x 24”) | |
| 95 litres | (18” x 24”) | |
| 180 litres | (22” x 30”) |
XTEMOS ELEMENT
AJAX PRODUCTS TABS ALTERNATIVE
Fashion
Steam Engine Model
Friction Board
Decade Inductance Box – 7 Dial
Description
Housed in a box with seven dials and fitted with 4 mm output plugs, the unit allows a range of inductances from 1ΩH to 10ΩH. 7 Decade Inductance Box (i) 1ΩH to 10ΩH in steps of 1ΩH (ii) 10ΩH to 100ΩH in steps of 10ΩH (iii) 100ΩH to 1mH in steps of 100ΩH (iv) 1mH to 10mH in steps of 1mH (v) 10mH to 100mH in steps of 10mH (vi) 100mH to 1mH in steps of 100mH (vii) 1mH to 10mH in steps of 1mHXTEMOS ELEMENT
AJAX PRODUCTS TABS ARROWS PAGINATION
Candle Holder
Dynamic Trolley, Wooden
Carboys
Carboys, made of polypropylene, are much lighter than glass.
These autoclavable, dependable & durable Carboys are provided with wide handles making it convenient while carrying or pouring purposes.
We also offer carboy with stopcock for the esteemed clients.
Material : Polypropylene
| Particulars | Pack (Pcs) | |
|---|---|---|
| Carboy 10 ltrs. | 1 | |
| Carboy 20 ltrs. | 1 | |
| Carboy With Stop Cock 10 ltrs. | 1 | |
| Carboy With Stop Cock 20 ltrs. | 1 |
XTEMOS ELEMENT
AJAX PRODUCTS TABS WITH ICONS
Digital Stroboscope
Description :-
Stroboscopic flashes are triggered by either the internal oscillator or by external pulses which may be connected to the two 4mm sockets mounted on the rear panel of the instrument. Example of the many applications of this unit are to be found in motion analysis multi exposures photography, examination of moving parts and measurement of rotational speed.
Specifications:-
Input Volts : 220V AC, 50 Hz
Flash Rate: 0- 9999 Flashes per minute.
Resolution : 1
Display: 7 Segment LED (4 nos.)
Gas Turbine/Turbojet Engine
XTEMOS ELEMENT
AJAX PRODUCTS TABS LOAD MORE PAGINATION
SILICA CRUCIBLE WITHOUT LID
PRODUCT DESCRIPTION
- Crucible is glazed inside and outside.
- Highly resistant to alkalis and hot temperatures
- 50ml capacity
- Outside diameter 55mm, 42mm height
- No lid includedSilica crucible is glazed inside and outside. Highly resistant to alkalis and hot temperature SIZES ARE: 15ML 25ML 50ML 80ML 100ML 150ML
SILICA CRUCIBLE TALL FORM Without Lid, Translucent
XTEMOS ELEMENT
AJAX PRODUCTS TABS CAROUSEL
Milling Tool Dynamometers
This is a simple and essay to understand set up introduce by sharp techno systems to study the behavior of cutting forces during milling operation in three directions. With this unit students can evaluate cutting depth, speed and feed. The unit works on standard method of octagonal ring with strain gauges. It is in to part one mechanical rings sandwiched between two M.S. plate with strain gauges fixed on it. This set of octagonal rings transmits the relevant data to the force indicator during milling operation.
FEATURES
1.Rigid construction & Compact Unit. 2.Assessment of cutting forces by giving due consideration to various parameters like depth of cut, material, cut, material, speed and feed. 3.Eassy in handling & Digital force indicators to measure three forces simuleniously.SPECIFICATIONS-
1.Mechanical sencing unit with set of octagonal rings and strain gauges. 2.Three channel digital force indicator with balancing potentiometers and polycarbonate front plate. 3.Range of force measurement in coordinate direction – 0 to 500 kg. 4.Over all size of mechanical unit- 300 x 300 mm.SERVICE REQUIRED
1.Necessary Milling Machine with automatic feed arrangement and tooling 2.230 volts, single phase, 50 Hz stabilized power supply.
Microscope Slide Set Biology
Set of 25, this set covers the major requirements for a basic course in biology.
Selected slides from the zoology, histology and botany sections make up this useful set.
Supplied in Box.
Paramecium, E
Paramecium, conjugation, E
Hydra, TS
Hydra, with testis, TS
Hydra, with ovary, TS
Taenia (tapeworm), scolex, LS
Taenia, proglottid, E
Compact bone, TS
Striated muscle, LS
Cardiac muscle, LS
Spinal cord, TS
Nerve cells, smear
Skin, VS
Kidney, VS
Lycopodium strobilus, LS Spirogyra, conjugation, E Yeast, E
Lilium (lily), anther, TS Dryopteris, pinnule with sori, TS
Stigma with pollen tube Lilium (lily), anther, TS Dryopteris, pinnule with sori, TS
Stigma with pollen tube Cucurbita (marrow), stem, TS Lillium, ovary, TS
Tilia (lima), young and old stem, TS
Lumbricus (earthworm), TS , Typhlosole
Helianthus, stem, secondary thickening, TS
Tool Dynamometers
A machine-tool dynamometer is a multi-component dynamometer that is used to measure forces during the use of the machine tool. Empirical calculations of these forces can be cross-checked and verified experimentally using these machine tool dynamometers.
(1) Milling Tool Dynamometers
(2) Grinder Tool Dynamometers
(3) Lathe Tool Dynamometers
(4) Drilling Tool Dynamometers
