XTEMOS ELEMENT
AJAX PRODUCTS TABS
Worm Sector Type Steering System
Worm & Sector Type Steering System – Actual Working
The working of steering system is shown with the help of actual parts assembled on square iron pipe frame. All the necessary parts of steering system are shown in actual working form. This model helps the student to understand the working of the steering system very easily. It is specially made dissectible for demonstration purposes.
Distillation Water Still (BARNSTEAD TYPE) Table Model S.S
CAVITY BLOCK
Transducer Trainer
Specification
• RTD acts as a temperature sensor • Strain gauge based load cell • Linear variable resistive transducer • LDR, Photo diode, photo transistor • Precision servo potentiometer • Inductive type proximity sensor • Heat source, Filament lamp, Buzzer • 3½ digit LED display • Analog type 10V Center-Zero meter • Inverting and Non-inverting amplifier • Amplifier with Gain and offset control • Instrumentation and summing amplifier • Low pass filter • Precision Rectifier • Timer and buzzer oscillator • Electric switchXTEMOS ELEMENT
AJAX PRODUCTS TABS SIMPLE
Hypsometer, Regnault’s
Description
Double walled copper cylinder, 340 x 60 mm, mounted on steam boiler, with thermometer tubule at top and side outlets for manometer and draining. Double walled copper cylinder 34 x 6 cm mounted on steam boiler. Fitted with thermometer, draining tube and glass manometer with rubber bungs. For the determination of the upper fixed points of thermometers andboiling points at barometric pressures other than atmospheric. Double walled copper cylinder 34 x 6 cm height x outer dia. mounted on steam boiler. Fitted with thermometer tubulure at the top, side outlet draining tube and glass manometer mounted in tubulure with rubber bungs.
Bio Periodic Tables
Description
Poly art Charts are multi colored, accurate in details, printed on plastic, laminated on both sides, washable, non-tear able and long lasting, with plastic rollers, size 75 x 100 cm. Periodic Table of Rare & Endangered species Periodic Table of Fishes Periodic Table of Vegetables Periodic Table of Fruits & Nuts Periodic Table of Birds
Grinder Tool Dynamometers
This a simple set up to study the various forces resolved during grinding operation, designed by sharp techno system for demonstration purpose for the students undergoing tool desing study. This unit works on octagonal ring method using strain gauge as a sensor. A two channel digital force indicator facilitates to measure both forces simulteniously.
FEATURES:
1.Rigid in construction & compact unit. 2.Assessment of cutting forces by giving due consideration to various parameters like depth of cut, material, speed and feed . 3.Eassy in handling & Digital force indicators to measure two forces simultaneously.SPECIFICATIONS:
1.Mechanical sencing unit with two octagonal rings and strain gauges. 2.Two channel digital force indicator with balancing potentiometers and polycarbonate front plate. 3.Range of force measurement in coordinate direction – 0 to 200 kg. 4.Over all size of mechanical unit – 300 x 300 mm.SERVICE REQUIRED:
1.Necessary surface grinding machine. 2.230 volts, single phase, 50 Hz stabilized power supply.
Insect Cage, Round Shape (Acrylic)
XTEMOS ELEMENT
AJAX PRODUCTS TABS ALTERNATIVE
Fashion
Newton Meters
Refrigerant Charging Unit
This charging unit is fitted with motorised vacuum pump and other safety devices like pressure gauge. With the help of this charging unit students can charge the refrigerant gases into compressor or store the gas of a refrigerator or air conditioner inside the cylinder fitted inside the charging unit that can be used later.
XTEMOS ELEMENT
AJAX PRODUCTS TABS ARROWS PAGINATION
LABORATORY JACK MILD STEEL
Product Description
Laboratory jack, an all purpose constructed from stainless steel, mild steel. Suitable for hot plates, burners, baths, glassware many more items. it is a knob operated scissor action lifting mechanism for quick, easy accurate height adjustment. Mild steel jacks are finished with powder coated. AVAILABLE SIZES:- Plate Size 8”x8”
- Plate Size 10”x10”
Tubing, Silicon
Electronic Ignition System Of An Automobile
XTEMOS ELEMENT
AJAX PRODUCTS TABS WITH ICONS
Distributed Control System
A powerful, modular & upgradable DCS has been designed and configured based on Siemens controller SIMATIC PCS7 ASRTX (Micro Box). Distributed I/O system ET200M can be provided for field automation. The distributed I/O can be connected via Profibus, Communication. DCS consists of controller, Power supply unit, distributed I/O, Digital Input and Output modules, Analog Input and Output module. a Demo Panel and Simatic PCS7 V9.0 Software.
DCS Controller
• Make : SIEMENS. • Controller : SIMATIC PCS 7 AS RTX BOX. • Profibus Communication done via CP5611 onboard. • Transmission Rate of Profibus cable is 12 Mbit/s. • 2 x GBIT & RJ45 LAN • Core 17-3517 Processor 1.7GHz, 4GB DDR3 RAM, SSD 80GB, 4xUSB V3.0 • Mouse and Keyboard • Windows7 • Win AC RTX 2010 software controllerDistributed I/O station ET200M
• Support HART, PROFIBUS, Foundation Field bus. • 16 No’s of digital Inputs with 24V DC. • 16 No’s of digital Outputs with 24V DC. • 8 channels of Analog Inputs with 4-20mA. • 8 channels of Analog Outputs with 4-20mA. • 24VDC /10A inbuilt power supply.
Demonstration Dynamo
Description
This model uses the same basic assembly as the motor, but is mounted on a baseplate 230 x 90 mm approx. which also carries a hand-drive pulley 120mm. diameter coupled to the smaller dynamo pulley by a rubber belt to give a step-up ration. Electrical output is via a pair of 4mm sockets. The model may also be used as a motor on a 6-8 V D.C. supply.
Pendulum Bobs dia 25mm- Set of 3 (Brass, Copper & Iron)
XTEMOS ELEMENT
AJAX PRODUCTS TABS LOAD MORE PAGINATION
SILICA CRUCIBLE WITHOUT LID
PRODUCT DESCRIPTION
- Crucible is glazed inside and outside.
- Highly resistant to alkalis and hot temperatures
- 50ml capacity
- Outside diameter 55mm, 42mm height
- No lid includedSilica crucible is glazed inside and outside. Highly resistant to alkalis and hot temperature SIZES ARE: 15ML 25ML 50ML 80ML 100ML 150ML
SILICA CRUCIBLE TALL FORM Without Lid, Translucent
XTEMOS ELEMENT
AJAX PRODUCTS TABS CAROUSEL
francis turbine test setup
DESCRIPTION:
Francis Turbine is a reaction Turbine, which was developed by English born American Engineer Sir J.B. Francis. The water enters the turbine through the outer periphery of the runner in the radial direction and leaves the runner in axial direction and hence it is called a mixed flow turbine. As the water flows to the runner, a part of pressure energy goes on changing into kinetic energy. Thus the water through the runner is under pressure. The runner is completely enclosed in an air tight casing and the casing & runner is always full of water. The present Set-up consists of a runner. The water is fed to the turbine by Means of centrifugal Pump, radially to the runner. The runner is directly mounted on one end of a central SS shaft and other end is connected to a brake arrangement. The circular window of the turbine casing is provided with a transparent. The circular window of the turbine casing is provided with a transparent acrylic sheet for observation of flow on to the runner. The runner assembly is supported by thick cast iron pedestal. Load is applied to the turbine with the help of brake arrangement so that the efficiency of the turbine can be calculated. A draught tube is fitted on the outlet of the turbine. The Set-up is complete with guide mechanism. Pressure and vacuum Gauge are fitted at the Inlet and Outlet of the turbine to measure the total supply head on the turbine.UTILITIES REQUIRED:
● Water Supply and Drain.● Electricity 15 kW, 440V Ac, Three Phase
TECHNICAL SPECIFICATIONS:
| MODEL | HM 101 (1.33 HP) | HM 101 (2 HP) | HM 101 (5 HP) |
| Output Power | 1.33 HP / 1 Kw | 2 HP / 1 Kw | 5 HP / 3.75 Kw |
| Discharge | 1000 LPM (Approx.) | 1000 LPM (Approx.) | 2000 LPM (Approx.) |
| Supply Head | 10 m | 10 m | 15 m |
| Rope Brake Dynamometer | Dia 200 mm | Dia 200 mm | Dia 300 mm |
| Sump Tank | Capacity 300 Ltrs. | Capacity 300 Ltrs. | Capacity 600 Ltrs. |
| Water Circulation Centrifugal Pump | Capacity 5 HP, Three Phase | Capacity 5 HP, Three Phase | Capacity 15 HP, Three Phase |
| Speed | 1500 RPM (approx.) | ||
| Runner | Having Curved Vanes | ||
| Discharge Measurement | Pitot Tube with Manometer | ||
| Control Panel | Star/Delta Starter, Mains Indicator, MCB for overload protection | ||
| The whole set-up is well designed and arranged in a good quality painted structure. | |||
Oscilloscope
This is a portable type of Oscilloscope for two traces. The band width is 0-20 MHz. The instrument is of easy operation with comfortable controls. Its reasonable structure and technology makes it convenient to repair and calibrate.
(1) Dual Trace Dual Channel Oscilloscope with Component Test Facility
(2) Bandwidth : 20 MHz
(3) Full bandwidth sweeping circuit is used in the sweeping system
(4) The flexible and convenient triggering mode has the functions for selecting signals from one channel or triggered by Ext signals
(5) ALT trigger to observe signals from two irrelative channels
(6) The instrument has the functions of TV-H / TV-V synchronization and trigger-lock to observe all kinds of signals stably
(7) From the terminal for trigger input, CH1 and CH2 signals can be output along with the triggering channel to connect the external frequency counter
(8) Y deflection operation : Y1, Y2, ALT, CHOP, ADD, mode X-Y
(9) Vertical Deflection : 5 mV / Div to 20 V / Div in factor 1-2-5 sequence in 12 steps
(10) Rising time : < 18 nS (11) Maximum Input Voltage : 400V (DC + ACp-p) (12) Triggering Source : Y1, Y2, ALT, POWER, EXT (13) Trigger Coupling : AC / DC (EXT), NORM / TV-H, TV-V (14) Horizontal Sweep Mode : AUTO, TRIG, LOCK, SINGLE (15) Sweep time factor : 0.1 uS / div to 0.2 s / div in 1-2-5 sequence in 20 steps (16) Magnification : x10 (17) X-Y Mode input : X-Axis Y1 and Y-Axis Y2 (18) Z Axis minimum input level : TTL Level (19) Component Test Facility (20) Calibration Signal : Square wave of 0.5 V at 1 kHz (21) CTR Display size : 8 cm x 10 cm (22) Auxiliary Power Supply : 220V 50Hz AC
Digital Coating Thickness Meter
Description
Digital Coating Thickness Meter We offer high quality of Digital Coating Thickness Gauge. Statistics (Number of readings, average, Std. deviation, max. ,; min.) are updated with every reading and displayed simultaneously. It helps to decide how many readings are to be taken. Continue taking readings till you start getting reasonably consistent statistics.
