XTEMOS ELEMENT
AJAX PRODUCTS TABS
Shear Centre Apparatus
Apparatus consists of sturdy base frame and Channel, Equal angle, Semicircle and Z-Section are supplied with apparatus. Standard length of each of the four sections in M. S. is supplied. Each is provided with end clamp for fixing to the rigid bracket. A special load hanger is provided so as to change the load position so that with the help of two dial-gauges, the vertical plane of Shear-centre for the particular section can be determined.
RANGE OF EXPERIMENTS:
1. Determination of the vertical plane of shear center for different cross sections commonly used for structures
Spartan 6 Trainer Kit
Features
• 16 Nos. of digital input using slide switches with LED indication • 16 Nos. of digital output using discrete LEDs • 16× 2 LCD is provided for display the text message. • One Reset Switch • One switch for giving manual clock • FPGA configuration through - On board Xilinx USB to JTAG Programmer with isolation to configure FPGA - On board Flash Prom XCF04S (Programmable through USB to JTAG programmer) • Total 186 I/O Pins: 100 Pins used for integrating peripheral like LED, Switches etc., balance pins are available to user • In 3nos of 20 pin header. • 1 No of 26 pin header to interface VLIM cards like Traffic Light Controller / On-board TLC (factory settable). • On board programmable PLL oscillator from1 MHz to 100MHz using jumpers • 4Nos of 7 segment LED display • One relay and Buzzer provided. • Stepper & DC motor drive provided on board (Motor Optional) • 4x4 matrix key provided • On board I2 C RTC Interface • On board Temperature Sensor Interface • SPI Based Analog to Digital Converter
Slotted Mas Set Iron
Demonstration Diffraction 3 in One
Description
For demonstrating the principle of the diffraction grating and the way in which its properties are dependent upon the number of lines per unit length. Comprises a card mount 90 x 40 mm approximately with three 16 x 9 mm apertures, each containing a diffraction grating replica. The gratings are of 100 lines / mm. 300 lines / mm and 600 lines / mm, respectively and are protected by cover glasses.XTEMOS ELEMENT
AJAX PRODUCTS TABS SIMPLE
Mechanical Heat Pump Trainer
Heat Pump is a device to pump heat from one source to another. The heat obtained by heat pump is more than that could be obtained by direct electrical heating. The apparatus consists of refrigeration system with water cooled shell and coil type evaporator and condenser.
SPECIFICATIONS:
1.Compressor – Hermetically sealed compressor using R-12 refrigerant, having capacity 0.3 tons of refrigeration. Condensing pressure – max. 15 Kg/cm2 (Actual pressures will depend upon working conditions). 2.Condenser – Shell and coil type with continuous water flow arrangement. 3.Evaporator – Shell and coil type with continuous water flow arrangement. 4.Expansion Valve – Internally equalized thermostatic expansion valve. 5.Measurements – a) Rotameter for condenser & evaporator water flow rate measurement. b) Rotameter for liquid refrigerant flow measurement. c) Pressure gauges for condensing and evaporating pressure – 2 Nos. d) Thermometer for refrigeration cycle & water temp, measurement – 7 e) Wattmeter for compressor input measurement. f) Ammeter for compressor current measurement. 6.Controls – a) HP/LP cutout for compressor. b) Overload protector for compressor. c) Gate valve to control water flow rates. d) Necessary switches and fuse. A technical manual is accompanies the unit.SERVICES REQUIRED:
1.Floor surface area – 2m, X 2m. X 1.5m. height. 2.220V. 15Amp. Single Phase Stabilized power supply.
Flourimeter (Digital)
A digital photofluorometer, you can perform precise analysis of flurophors and quinine.
Designed specifically for life science laboratories, this smart instrument fulfills your requirements of accurate results with the sensitivity you demand.
This fluorometer is a compact system, which occupies very low bench space, while offering convenient and excellent throughput for fluorescence assays.
It is a fluorometer model has been designed and manufactured for laboratories, where routine analysis of fluorophors is a prime requisite.
This system uses 50 W tungsten halogen lamp,
This digital fluorometer greatly enhances productivity of your laboratory, designed with latest technology, use of imported mechanical and electrical parts, imported lamp and other components; it allows you to perform fluorometric determination of quinine more quickly.
| Covers entire visible range: | Excellent detection sensitivity | |
| Compact and efficient: | Bright red seven segment LED display | |
| Occupies low bench space: | Precise analysis of Flurophors & Quinine |
Specifications
| Fluoro Sensitivity: | Full-scale deflection obtained with 1 ppm quinine sulfate in 0.1 N sulphuric acid (primary wavelength 360 nm) | |
| Display: | 3 digits bright red seven segments LED display | |
| Excitation Source: | 12V, 50W Tungsten Halogen Lamp | |
| Sensitivity Range: | Adjustable in 4 ranges | |
| Detector: | Highly sensitive wide range photodiode/cell | |
| Sample Test Tube Size: | 15 mm (D) x 80 mm (H) | |
| Minimum Sample: | 4 ml | |
| Power: | 230 V ± 10%, 50 Hz. AC | |
| Dimension: | 260 x 335 x 160 mm (Approx.) |
Steam Engine Model With Boiler
XTEMOS ELEMENT
AJAX PRODUCTS TABS ALTERNATIVE
Fashion
Gear Pump Test Setup
DESCRIPTION:
The Set-up is designed to study the performance of Gear Pump. The Set-up consists of a Gear Pump having a pair of meshed gears coupled with electrical motor, supply tank, measuring tank & pipe fittings for closed loop oil circulation. Pressure and Vacuum Gauges are connected on delivery and suction side of pump for the purpose of measurement. The flow rate of water is measured using measuring tank and stop watch provided.EXPERIMENT:
Ø To determine overall efficiency and pump efficiency of the Gear Pump Ø To plot Head vs. Discharge, Pump efficiency vs. DischargeFEATURES:
Ø Closed loop water circulation Ø Compact & stand alone set-up Ø MS Excel sample calculation program on demand Ø Stainless Steel tanks and wetted parts Ø Superb painted structure Ø Simple to Operate & MaintainUTILITIES REQUIRED:
Electric Supply: – Provide 230 +/- 10 VAC, 50 Hz, Single Phase Electric Supply with proper earthing. (Neutral – Earth voltage less than 5 VAC) 5 A, three pin socket with switch for pump. Oil Supply: Oil @ 30 Ltrs. (Optional extra cost)TECHNICALS SPECIFICATIONS:
Ø Pump : Gear Pump with pair of meshed gears Capacity 1 HP,Speed 1500 RPM (max.), Head 5 Kg/cm2 (max.) Ø Drive : AC Motor with step cone pulley arrangement for 3 prefixed speed DC Motor with DC Drive along with (non-contact type Digital RPM Indicator Ø Supply Tank : Capacity 30 Ltrs. Ø Measuring Tank : Capacity 20 Ltrs. fitted with Piezometer Tube & Scale Ø Piping : GI / PVC Ø Stop Watch : Electronic Ø Control Panel : With required electrical instrumentation (The whole Set-up is well designed and arranged in a good quality painted structure.
Insect Storage Box
Description
For pinning of insects both inside top & bottom, White hardwood / Teakwood frame with melamine lamination on top & MDF sheet bottom is nicely polished. Top & bottom lined with 8mm thick soft pinning. washable EVA sheet. Inside glazed white. Raised wall with holes for insecticide inside bottom to make box air tight and pest proof. Fitted with brass hinges. index card holder & clips. Insect Storage BoxSize 53x45x9 cm Insect Storage BoxSize 45x30x7.5 cm Insect Storage BoxSize 38x25x7.5 cm Insect Storage BoxSize 30x23x7.5 cm
Micrometer Screw Gauge
Micrometer Screw Gauge
• Strong rugged metal construction.
• Economical, suitable for all uses, teaching, demonstration, labs, machine shops.
• Measuring screw handle, Satin finish with friction knurling for easy rotation.
• With locking mechanism to hold measurements.
• 25 x 1 mm, reads to 0.01 mm.
• Supplied with hex wrench for zero adjustment and plastic case for storage.
Anaerobic Culture Jar
Description
Transparent Anaerobic Culture Jar of 3.5.lit. capacity which is made of Polycarbonate. The lid of the jar is made of Aluminum pressure die Casting fitted with Pressure Valve, Vacuum Valve, Safety Valve & compound Pressure cum vacuum gauge, three finger aluminum clamp and sealing "O" ring. This is recommended only where inside air of jar is removed thru vacuum pump and CO2 is filled in the jar thru CO2 gas cylinder to generate anaerobic condition in the jar. Also supplied with plain aluminum pressure die casted lid which can be fitted when readymade gas packs are used to generate the anaerobic conditions inside the jar. When readymade gas packs are used, there is no need of lid fitted with dial gauge etc., for extra life of equipment.XTEMOS ELEMENT
AJAX PRODUCTS TABS ARROWS PAGINATION
Ghat Tracer
Slide Box
We are the major Exporter and Trader of superior quality Slide Boxes .
These Slide Boxes are durable, compact & provide utmost protection to 1" x 3" slides.
Heavy walls will not warp, splinter or crack.
Our Slide Boxes are unaffected by humidity and are thoroughly insect proof.
| Particulars | Pack (Pcs) | |
|---|---|---|
| Slide Box - 25 Slides | 12 | |
| Slide Box - 50 Slides | 12 | |
| Slide Box - 100 Slides | 6 |
Melting Point Apparatus
Description
Mechanical Type (Routin) Phase : Single Phase Power : 50Hz Melting Temperature : upto 230ËšC Voltage : 220V Features: The mounting block is illuminated from below by a lamp fixed in its housing. The aluminum block accepts three capillary tubes and mercury thermometer. The temp is regulated by energy regulator fitted to the unit. Supplied without capillary tubes and thermometer
Resistance Units
XTEMOS ELEMENT
AJAX PRODUCTS TABS WITH ICONS
Three Step Inductor
Description
This three step inductor consists of a coil of enamelled copper wire wound over an insulated spool. The coil consists of 4 layers of 200 turns each. The tappings at 200, 400 and 800 turns are brought out at 4 mm sockets. The output inductances at these tappings are as follows. No. of turns Resistance 200, Inductor 0.3 mH, Resistance 0.6Ω No. of turns Resistance 400, Inductor 1.2 mH, Resistance 1.2Ω No. of turns Resistance 800, Inductor 5.0 mH, Resistance 2.6Ω. One can easily change the inductor value of the instrument on just inserting a soft iron core inside the bobbin
Color Target Comparator
Description
Color Target Comparator The colour meter for both colour and luminance measures surface colours of products. The CR series colour meter is included in our professional range. This colour meter can read the difference in colour in L d*a*b*, L*C*H* and Delta E*ab according to your requirements. The most popular model of colour meter in our range of products is the PCE-RGB. Aside from being easy to use and economical, the colour meter is used for determining the location of a colour on the XYZ axis of non-radioactive products. The geometry of the measurement of these colours, with luminosity including a field of measurement of 8mm, allows for universal use for all types of materials. Furthermore, these devices are used by artisans, paint manufacturers, architects, painters and designers for testing colours (for colour card, NCS, RAL, HKS) or for establishing colours after mixing various colours. If you have any queries, please contact us at.
XTEMOS ELEMENT
AJAX PRODUCTS TABS LOAD MORE PAGINATION
SILICA CRUCIBLE WITHOUT LID
PRODUCT DESCRIPTION
- Crucible is glazed inside and outside.
- Highly resistant to alkalis and hot temperatures
- 50ml capacity
- Outside diameter 55mm, 42mm height
- No lid includedSilica crucible is glazed inside and outside. Highly resistant to alkalis and hot temperature SIZES ARE: 15ML 25ML 50ML 80ML 100ML 150ML
SILICA CRUCIBLE TALL FORM Without Lid, Translucent
XTEMOS ELEMENT
AJAX PRODUCTS TABS CAROUSEL
Electrical Power Steering System Actual Working
Electrical Power Steering System – Actual Working
The working of steering system is shown with the help of actual parts assembled on square iron pipe frame. All the necessary parts of steering system are shown in actual working form. This model helps the student to understand the working of the steering system very easily. It is specially made dissectible for demonstration purposes.
Botany Charts
Description
Poly art Charts are multi colored, accurate in details, printed on plastic, laminated on both sides, washable, non-tearable and long lasting, with plastic rollers, size 75 x 100 cm. T.S. in Dicot & Monocot stem Pinus-1 Male & Female Strobli L.S. Shoot Apex & it’s different regions T.S. Shoot Apex & it’s different regions Plant Tissue Cork L.S. in Flower with T.S. in Anther Plant tissue Xylem T.S. in simple Pit Pinus II through female Strobilus L.S. through ovules Plant tissue Collenchyma Marchantia Life Cycle Plant Tissue Parenchyma L.S. in Root Tip & T.S. in its different regions Marchantia T.S. of Root (Secondary Growth) Adiantum Life Cycle Stages of formation of Female Gametophyte with the process of Pollination, Fertilisation & Formation of seed Plant Tissue Phloem Plant Tissue Sclerenchyma T.S. in Stem to show growth with a drawing of Lenticel Adiantum T.S. Dicot & Monocot Root Typical plant cell, English only Plant Mitosis English only Plant Meiosis, English only Classification of Plants, English only
