XTEMOS ELEMENT
AJAX PRODUCTS TABS
Set of Springs
Pyrometer
Description
Fitted on a wooden base cast metal uprights and rod mountings. A 20-0-20 scale is provided to notice the expansion in rods. The counter weighted needle is used for easy reading. A knurling screw is provided for zero adjustment. Supplied with three metal rods one of each Aluminium, Brass and Steel.
Manual Steering System
Steering System – Actual Working
Manual Steering System
The working of steering system is shown with the help of actual parts assembled on square iron pipe frame. All the necessary parts of steering system are shown in actual working form. This model helps the student to understand the working of the steering system very easily. It is specially made dissectible for demonstration purposes.
XTEMOS ELEMENT
AJAX PRODUCTS TABS SIMPLE
Lens, Biconvex, Acrylic
Trans-Ratio
Description
Trans-Ratio is a simple transformer system that allows students to investigate the relationship between primary voltage, secondary voltage and the turns ratio. The Primary coil has tappings at 200, 400 and 600 turns while the Secondary has 100, 200, 300, 400, 500 and 600 turns all brought out to 4mm sockets. An AC supply of upto 6 V as well as AC voltmeters are required for demonstration purpose.
Light Dependent Resistor Unit (LDR)
XTEMOS ELEMENT
AJAX PRODUCTS TABS ALTERNATIVE
Fashion
Wheatstone Bridge
Specification
• Four arms with one unknown arm to connect the unknown resistance • Two range selection arms provided to select the nearest range of unknown value. • Range of Measurement : 5Ω-100KΩ • Accuracy (Min to Max.) :±0.2 ± 5Ω • Tolerance : ±5% • Digital voltmeter (Range +5V to - 5V) is provided to indicate the Balance conditions • Built-in power supply
PATHOLOGY INCLINED MONOCULAR MICROSCOPE
PRODUCT DESCRIPTION:
OBSERVATION HEAD: MONOCULAR Inclined at 45° and Rota table 360º with perfectly centered Quadruple BAL Bearing revolving nose piece. OBJECTIVE- 4/5x, 10x, 40/ 45x, 100x (oil). EYE PIECES- 10x WF (one), Huygenian 5x or 15x (Any one)MECHANICAL STAGE: Double plate 130x140 mm Low drive mechanical stage for X & Y movement with Sub stage bright field condenser N.A. 1.25 & iris diaphragm with built in swing out filter holder and up-down movement through rack & pinion. FOCUSING SYSTEM: Separate Coarse & highly sensitive fine movement mechanical graduated to 0.02mm. With locking device. EXTRA LARGE BASE: To support the robust arm, has built in with LED cooled bright Illumination or 6V 20 W HALOGEN LAMP with soft start continuously variable intensity controlled regulator & quick change bulb provision. PACKING: Microscope supplied one Plano concave mirror for use in day light, duster, cover & instruction manual.
Dicot Stem Anatomy T. S. & L. S.
Description
This model shows the transverse and longitudinal section of a dicotyledonous stem in which case the cambium ring has been formed but no secondary growth has yet taken place. Useful model for study of epidermis, lentice , cork layer, cork cambium, cortical parenchyma ,starch sheath, medullary rays, phloem, sieve plate, sieve tube, phloem parenchyma and inter fasicular cambium ,xylem, pitted vessels, bordered pitted vessels, annular vessels, spiral vessels, pith etc. Mounted on base, with key card.
Refrigeration Trainer General Cycle Type
The unit consists of vapor compression refrigeration cycle provided with components normally used in refrigeration system so that student can get familiar with the components. Various measurement provided enable students to estimate the performance of the system.
SPECIFICATIONS:
1.Compressor- Hermetically sealed compressor, having capacity of 0.3 T. 2.Expansion Devices a) Thermostatic Expansion Valve b) Capillary tube. 3.Evaporator coil. 4.Controls: a) Services Valve b) Solenoid Valve c) Filter-Drier for refrigerant d) High/Low pressure cutout e) Thermostat. 5.Measurements: a) Thermometers (mercury in glass) – 4 Nos. b) Pressure gauges for condensing and evaporating pressure. c) Energymeter for compressor d) Voltmeter and Ammeter for compressor. e) Rotameter for liquid refrigerant flow measurement. A technical manual is accompanies the unit.SERVICES REQUIRED:
1.Floor surface area – 1m x 2m x 2m height. 2.220V, I5Amp, Single Phase Stabilized power supplyXTEMOS ELEMENT
AJAX PRODUCTS TABS ARROWS PAGINATION
Lens Holder Wooden
Study Of Pipe Fitting
DESCRIPTION:-
The Set-up consists of a ½ bend and elbow, a sudden expansion & sudden contraction fitting from 15 mm to 25 mm, ball valve and gate valve. Pressure tapings are provided at inlet and outlet of these fittings under test. A differential manometer fitted in the line gives pressure loss of individual fitting. Present Set-up is self-contained water re-circulating unit, provided with a sump tank and a centrifugal pump etc. Flow control valve and by-pass valve are fitted in water line to conduct the experiment on different flow rates. Flow rate of water is measured with the help of measuring tank and stop watch.EXPERIMENTS:-
Ø To determine loss of head in the fitting at various water flow rates. Ø To measure the loss co-efficient for the pipe fittings.UTILITIES REQUIRED: –
Ø Water Supply and Drain Ø Electricity Supply: Single Phase, 220 V AC, 0.5 kW.TECHNICAL SPECIFICATION: –
Ø Sudden Enlargement : From 15 mm to 25 mm Ø Sudden Contraction : From 25 mm to 15 mm Ø Bend : ½ Ø Elbow : ½ Ø Ball Valve : ½ Ø Gate Valve : ½ Ø Water Circulation : FHP Pump, Crompton / Sharp make Ø Flow Measurement : Using Measuring Tank with Piezometer, Capacity 25 Ltrs. Ø Sump Tank : Capacity 50 Ltrs. Ø Stop Watch : Electronic Ø Control Panel : On / Off Switch, Mains Indicator etc. The whole Set-up is well designed and arranged in a good quality painted Structure
XTEMOS ELEMENT
AJAX PRODUCTS TABS WITH ICONS
Behaviour Of Column Struts Apparatus
Apparatus consist of four spring steel columns which are put along a vertical wooden board. These four columns have different end conditions as below:
1. Both ends pinned
2. Both ends fixed
3. One end pinned and other fixed
4. One end fixed and other end free
Apparatus to be supplied should be complete with a supporting stand and a set of weights.
Ocean Features Model
Rules Steel
XTEMOS ELEMENT
AJAX PRODUCTS TABS LOAD MORE PAGINATION
SILICA CRUCIBLE WITHOUT LID
PRODUCT DESCRIPTION
- Crucible is glazed inside and outside.
- Highly resistant to alkalis and hot temperatures
- 50ml capacity
- Outside diameter 55mm, 42mm height
- No lid includedSilica crucible is glazed inside and outside. Highly resistant to alkalis and hot temperature SIZES ARE: 15ML 25ML 50ML 80ML 100ML 150ML
SILICA CRUCIBLE TALL FORM Without Lid, Translucent
XTEMOS ELEMENT
AJAX PRODUCTS TABS CAROUSEL
Specimen Jar
We have come up with a quality range of Specimen Jars.
These transparent Specimen Jars are used for preserving different specimens in the lab and are provided with a cap that fits in tight.
These jars provided excellent protection to the species preserved in it.
Material : Polystyrene
| Particulars | Pack (Pcs) | |
|---|---|---|
| Specimen Jar (Gas Jar) | 12 |
DC Network Analyzer
Specification
• Here we provide the bi-polar Transmission Line. • Simulated long, medium & short distribution lines selectable by patching in various length of DC Transmission line • Two no of bi-polar DC generator sources with ON/OFF control and voltage regulator potentiometer. - Two wire or Three wire Transmission Line operated in +12V DC - Each DC generator are independently control by potentiometer. • 2 digital voltmeters and ammeters provided in the input side and 2 digital volt meters and ammeters are provided in the output side • of transmission line to read the input & output parameters of transmission line. • One no of microcontroller based measuring system provide to read the input and output parameters. • 4 nos of digital ammeters provided to read the load current • 4 nos of resistive load and 4 nos of lamp loads are provided to load the transmission line.
Outside Micrometers (Etching Marking)
Description
Micrometer is used to measure short lengths accurately Technical Details : ; Carbide Tipped Measuring Faces ; Blue Metallic Finish Frame ; With Locking Clamp and ratchet stop ; Printed Marking on the Vernier Scale ; Least Count : 0.01mm/0.001” Sizes Sizes 0-25 0-1” 25-50 1-2” 50-75 2-3” 75-100 3-4” 100-125 ; 125-150 ; 150-175 ; 175-200 ; Specifications: Guarantee ; 6 Months without abuse Packing ; Plastic Box Calibration ; In house.
Curved Member Apparatus
Apparatus consists of a steel bar which is used to make the different curved members Viz. circle, semicircle with straight arm, a quadrant of a circle and quadrant of a circle with straight arm. The bottom ends of the members are fixed to the base. Under the application of load at free end, its horizontal and vertical deflection can be measured with the help of dial gauges. A dial gauge with 25mm travel (with a magnetic base) is supplied with the apparatus. Apparatus to be supplied should be complete with a supporting stand and a set of weights.
Experimental Capabilities: Apparatus is supplied complete with a supporting stand and a set of weights.
Fluid Mechines Hydraulic Machines Models
FLUID MECHANICS & HYDRAULIC MACHINES MODELS
1. Hook Gauges
2. Venturimeters & Orificemeters
3. Manometers
(A) Pitot Tube
(B) U Tube Double Column Manometer
(C) Differential Manometer
(D) Inclined Manometer
4. Valves Models
(A) Hydraulic Non Return Valve
(B) Gate Valve
(C) Globe Valve
5. Turbines & Pumps Models
(A) Different Impellers Of Pumps And Turbines (Set Of 8) :
(i) Mixed Flow Runner Cast Aluminium
(ii) Axial Flow Runner Cast Aluminium
(iii) Radial or Centrifugal Runner Cast Aluminium
(iv) Kaplan Runner Cast Aluminium
(v) Francis Runner Cast Aluminium
(vi) Domestic Self Pumping Runner of Brass
(vii) Centrifugal Runner Actual Cast Iron
(viii) Pelton Wheel Runner Cast Aluminium
(B) Display Board For Pipes
(C) Hydraulic Elevator:
(D) Hydraulic Ram Non Working Model
(E) Pelton Turbine Model
(F) De-Lavel Turbine Model
(G) Kaplan Turbine Model
(H) Francis Turbine Model
(I) Impulses Turbine Working Model
(J) Air or Steam Pressure Turbine Model
(K) Pure Reaction Turbine Model
(L) Radial Turbine Model
(M) Gear Pump Model:
(N) Rotary Pump
(O) Centrifugal Pump : Actual Cut Section
(P) Reciprocating Pump : Actual Cut Section
(Q) Model Of Air Lift Pump Model
(R)Pendulum Pump Model
(S) Archemedian Screw Pump Model
(T) Tubewell Model :
(U) Deep well Turbine Pump Model
(V) Submersible Pump Model
(W) Hydro-Electric Power Installation Model
