XTEMOS ELEMENT
AJAX PRODUCTS TABS
Metal Rivets, Brass
Description
Supplied as rivets. Pk of 500gms. Brass,lead,aluminium,iron, For specific heat capacity experiments. Supplied as rivets. Packets of 500 grams.300 mm long x 3 mm dia. Supplied in packets of ten rods. Copper,iron,lead,aluminium,brass 300 mm long x 3 mm dia. Supplied in packets of ten rods.
SILICA BASIN (Round Bottom) with spout
PRODUCT DESCRIPTION
Round Bottom Basin With Spout is high purity material that enables products to resist corrosion and withstand the sharp change in temperature. Both of them meet requirements acquired by chemical and physical analysis and have 200ml Capacity.
Available in Different Dimensions:
20ml, Dia. 55mm x Ht. 23mm
45ml, Dia. 75mm x Ht. 27mm
70ml, Dia. 87mm x Ht. 33mm
85ml, Dia. 94mm x Ht. 36mm
100ml, Dia. 100mm x Ht. 45mm
200ml, Dia. 113mm x Ht. 47mm
Demonstration Dynamo Model
Human Digestive System
XTEMOS ELEMENT
AJAX PRODUCTS TABS SIMPLE
Draining Rack
Draining Rack provides an excellent option for post wash draining of tubes & bottles in the laboratory.
The back plate of this Draining Rack has 20 holes into which pegs are tightened with the help of screw-nuts.
Bottom of the rack is provided with a tray which collects all the waste water drained down which can further be collected in a container via drain tube.
This rack not rot, stain or rust.
Material : Acrylopitrile Butadiene Styrene / Polycarbonate
| Particulars | Pack (Pcs) | |
|---|---|---|
| Draining Rack | 1 |
Forceps (Different Types)
Burner Bunsen, LPG
XTEMOS ELEMENT
AJAX PRODUCTS TABS ALTERNATIVE
Fashion
Citical Radius Of Insulating Material
Citical Radius of Insulating Material:
At particular radius of insulation over a cylinder, loss of heat is maximum. The unit consists of a G.I. pipe provided with plaster of Paris insulation on out side surface. Four pipes are provided with heater inside having input control. Input to heaters is measured by common voltmeter and ammeter, by controlling input to heaters, it is shown that critical radius of insulation is ratio of thermal conductivity and outside heat transfer co-efficient.
SPECIFICATIONS:
1.G. I. Pipes with electrical heater inside – 4 Nos. 2.Insulation over the pipes of different thickness. 3.Controls and Measurements – a) Dimmerstat to control heater input – 4 Nos. b) A voltmeter and ammeter to measure inputs to heater. c) Digital temperature indicator to measure temperatures across insulation. d) Necessary switches and controls. A technical manual accompanies the unit.SERVICES REQUIRED:
230 V, 5 Amp., A.C., Supply with earthing connection. Floor Area of 1 m. X 1 m X 1.5m. height.
Mosquito Breeder
XTEMOS ELEMENT
AJAX PRODUCTS TABS ARROWS PAGINATION
T-Joint
Ticker Tape Timer
For the measurement of velocity and acceleration, using timing marks made on a moving paper tape by a vibrating striker.
Designed to operate on a 12V A.C. supply and uses the mains frequency as its timing standard.
The unit is housed in a moulded case including mounting flanges.
The top of the case caries a tape guide which incorporates a carbon paper disc support and an adjustable anvil for the striker point.
All moving parts are fully enclosed and a pair of 4mm sockets are provided on the side of the case for connection of the electrical supply.
Supplied with a roll of self marking paper tape.
Paper tape : 100m of paper tape, 9.5mm wide.
Carbon Paper Discs : 40mm diameter, with 3mm hole, cut from long life plastic film type carbon paper.
Displacement Vessel, Glass
XTEMOS ELEMENT
AJAX PRODUCTS TABS WITH ICONS
Tablet Making Machine (Hand Operated)
Details
Single punch automatic compression and injection device with each revolution of the wheel drive automatic feed and remove of tablets. Built on heavy cast body with centric pressure system SS hoper provided and connected by a rubber tube easy setting for thickness and hardness of tablets with nuts and locknuts.Features
Easily rotating wheel for making tablets. Compressing lever for adjustable harness of tablets. Adjustable lower punch for adjusting the thickness. Stainless steel day and punch size 6, 9, 12 mm. Electrical model can be provided in same with ½h.p motor.
three-phase-flying-capacitor-5-level-inverter-power-module
Specification
• Power circuit consists of 24Nos, 1200V, 20A IGBT with proper heat sink and snubber circuit. • 18 Nos of flying capacitor provided • 6 Nos, Power Diode @ 500v is provided for power circuit • 24 Noshigh speedopto-isolator provided for IGBT PWM inverter. • 24 Nos IGBT gate driver IC provided for IGBT gate driving • 22 nos isolated +15v dc @ 0.5A capacity provided for control circuit • One no of 3phase diode bridge rectifier@1200V, 20A with capacitor provided for input AC-DC conversion • 3 no of Hall Effect current sensor provided for O/P current measurement & protection circuit • 1 no Hall Effect current sensor provided for DC current measurement • Two no FRC connector provided for IGBT PWM input & ADC interface • MCB protection for input power ON/OFF & protection • One no of restart switch and LED provided for protection circuit indication & reset the unit • One Number of analog DC voltmeter provided for DC voltage measurement. • One number of power ON/OFF switch provided. • 3 Phase outputs & 3 Phase inputs are terminated in the front panel. • Test points provided for PWM input and current sensors output
Brush, Semi Micro
Recalculating Ball Type Steering System
Recalculating Ball Type Steering System – Actual Working
The working of steering system is shown with the help of actual parts assembled on square iron pipe frame. All the necessary parts of steering system are shown in actual working form. This model helps the student to understand the working of the steering system very easily. It is specially made dissectible for demonstration purposes.
XTEMOS ELEMENT
AJAX PRODUCTS TABS LOAD MORE PAGINATION
SILICA CRUCIBLE WITHOUT LID
PRODUCT DESCRIPTION
- Crucible is glazed inside and outside.
- Highly resistant to alkalis and hot temperatures
- 50ml capacity
- Outside diameter 55mm, 42mm height
- No lid includedSilica crucible is glazed inside and outside. Highly resistant to alkalis and hot temperature SIZES ARE: 15ML 25ML 50ML 80ML 100ML 150ML
SILICA CRUCIBLE TALL FORM Without Lid, Translucent
XTEMOS ELEMENT
AJAX PRODUCTS TABS CAROUSEL
Leopold Maneuvers Simulator
Description
One piece fetal baby with palpable fontanelles, spine, shoulders, elbows, and knees Fetal baby may be placed in normal, breech, or transverse position Fetal baby cradled between two “cushions” Cushions may be inflated independently of the other; inflation of the lower cushion raises the fetus to desired position; inflation of the upper cushion creates a firm abdomen as in the ninth month of pregnancy The Palpation Module is designed to be used with the Advanced Childbirth Simulator.
Monocot Stem Anatomy T.S &L.S
Description
This model exhibits the various tissues and the scattered, closed and collateral vascular bundles in transverse and longitudinal sections in maize. The large pitted vessels, spiral and annular vessels show the cell wall thickenings in L.S. Useful model for teaching anatomy of monocot stem. Mounted on base with keycard.
Water Bath Recangular Type
Specifications
It is a double walled unit inner chamber made up of S.S. Sheet and outside of M.S. duly powder coated. The gap between the walls is fitted with special grade glass wool in order to avoid thermal losses. Concentric rings can be removed to accommodate containers of various sizes. Temperature from ambient to 100°C is controlled by Hydraulic capillary type thermostat with accuracy of ± 1° C . Workable on 220V AC 50Hz Single Phase.| Chamber Size In mms | Holes | Cap. (Aprox.) |
|---|---|---|
| 300x250x100 | 6 holes of 75 mm | 8 L |
| 355x405x100 | 12 Holes of 75mm | 15 L |
Micrometer Screw Gauge
Micrometer Screw Gauge
• Strong rugged metal construction.
• Economical, suitable for all uses, teaching, demonstration, labs, machine shops.
• Measuring screw handle, Satin finish with friction knurling for easy rotation.
• With locking mechanism to hold measurements.
• 25 x 1 mm, reads to 0.01 mm.
• Supplied with hex wrench for zero adjustment and plastic case for storage.
Transmission Line Trainer
This trainer is designed for study of co-oxial cable characteristics like Impedance measurement, VSWR measurement etc., It is based, i) The latest technology of DDS Based RF source. ii) Directional coupler for VSWR Measurement. iii) TDR to measure the cable fault.
