XTEMOS ELEMENT
AJAX PRODUCTS TABS
Magnifier, Folding
Sterility Test Apparatus (S.S Manifold)
It consists of Stainless steel holders in the manifold of 3 of 6 to hold 47 mm dia membrane filters, the tops of the holders are connected to the outlets of flushing tube with silicone tubing and glass top cock.
A vacuum resistant flask or wolf bottle must be placed between the manifold and vacuum pump.
(Supplied without wolf bottle and vacuum/pressure pump).
These units are used for sterility testing when the membranes filter is to be removed from the holder for incubation in culture media.
Filtration area is 12.5 cm and has a holding capacity of 250ml.
Though the only vacuum is required for filtration, some pressure is required for flushing liquids.
SPECIFICATIONS
| Material: | Stainless Steel | |
| Branch Test: | 3 Dia. 47mm | |
| Filtration Area: | 12.5 cm | |
| Holding Capacity: | 250 ml |
FEATURES
Robust design. Easy to use. Rustproof.APPLICATION
For microbiology, biochemistry, hydrobiology (DNA/RNA). Beverage analysis & food testing. Protein binding, gravimetric analysis, coliform, yeast, mould total bacteria & sterility testing. Ideal for water & wastewater analysis. Residue precipitate analysis and contamination tests. General Liquid Filtration.Single Test (Filter Holder S.S) Three Test
Elastically Coupled Beam Apparatus
Apparatus consists of a three parallel bar suspension system with elastic beam at their upper and lower ends. The upper ends of the two outer suspension rods are tied to a vertical wooden board while central suspension rod may be tied to the centre of another elastic beam supported at two outer ends only. Mild steel Apparatus to be supplied should be complete with a supporting stand and a set of weights.
XTEMOS ELEMENT
AJAX PRODUCTS TABS SIMPLE
Bending Moment & Shear Force Apparatus
INTRODUCTION:
Shear Forces occurs when two parallel forces act out of alignment with each other. For example, in a large boiler made from sections of sheet metal plate riveted together, there is an equal and opposite force exerted on the rivets, owing to the expansion and contraction of the plates. Bending Moments are rotational forces within the beam that cause bending. At any point within a beam, the Bending Moment is the sum of: each external force multiplied by the distance that is perpendicular to the direction of the force.EXPERIMENT MANUAL:
1. To verify the Shear force a cross-section of the beam. 2. To verify the bending moment in cross–section of beam with a flexure condition.APPARTUS SPECIFICATION:
1. Dimensions : 158 cm X 45cm X (h)60cm 2. Total Beam Length : 160 cm with flexure 3. Width of Beam : 5 cm 4. Distance of Length in between : 5 cm 5. Height of beam : 36 mm 6. No. of Hanger for weights : 3 7. No. of Spring Balance : 2 (of 10kg) 8. Total Weight of Apparatus : 13.1 kgACCESSORY REQUIRES:
1. Shear force apparatus 2. Bending Moment Apparatus 3. Hangers 4. Weights 5. Two Spring balances – 10kgs
Shunt Active Filter Trainer
Specification
• FPGA Spartan 3A DSP board used for generating the PWM signals. • Three phase 3 level diode clamped inverter used as a Active filter. • SRF (or) Instantaneous PQ theory will be used to generating reference current. • PI control or fuzzy logic will be used to regulate the dc link capacitor voltage. • Reference DC link Voltage will be 250V. • Hall effect current transducers used to sense the source currents, load currents and compensation currents. • Hall effect voltage transducers used to sense the dc link voltage and source voltages. • Necessary source inductor and filter inductor provided. • Input source Line voltage -200V (Peak). • Input source Current -10A (Peak). • Power Rating -3KW. • Reactive power compensation can be provided. • 3KW linear and non-linear loads will be given. • User can modify source, filter inductance and external loads. • User can modify control algorithm. • Industrial type cabinet provided. • Before compensation source current THD will be greater than 26% • After compensation source current THD - 2.5 - 4% in 3 level inverter - 4 - 5% in 2 level inverter
Micro Controller Development Board
Microcontroller development board is designed to train engineers about the structural design, instructions and utilize the 8051 microcontroller board. A 40 pin ZIF socket for easy insertion of 89 series microcontroller with four 10 Pin FRC connectors is provided on the board. Outputs from I/O port from microcontroller are available on FRC connectors those can be easily connect with different modules. Microcontroller Development Board consists of EEPROM with 4K memory changeable with more RTC DS1307 with 32 KHz crystal with battery backup One 12 V stepper motor with drivers.One 16 x 2 LCD display. 8 Output LED indicators. 4 multiplexed 7-segment display. 8 single bit toggle switch. 4 x 4 matrix keyboard. Single Channel ADC with potentiometer and provision of external inputs RS 232 serial communication. One 12 V DC motor driver.
Human Physiology Charts
Description
Poly art Charts are multi colored, accurate in details, printed on plastic, laminated on both sides, washable, non-tearable and long lasting with plastic rollers, size 75 x 100 cm. Skeletal System Muscular system Circulatory system Nervous system Digestive system Teeth & skin Human eye, ear & head Lymphatic system Respiratory system Endocrine system Nutrition Immune system Human Nose Human Heart Excretory system Human Eye Human Ear Human Kidney Human Lungs Human LiverXTEMOS ELEMENT
AJAX PRODUCTS TABS ALTERNATIVE
Fashion
LABORATORY JACK MILD STEEL
Product Description
Laboratory jack, an all purpose constructed from stainless steel, mild steel. Suitable for hot plates, burners, baths, glassware many more items. it is a knob operated scissor action lifting mechanism for quick, easy accurate height adjustment. Mild steel jacks are finished with powder coated. AVAILABLE SIZES:- Plate Size 8”x8”
- Plate Size 10”x10”
Digital Stroboscope
Description :-
Stroboscopic flashes are triggered by either the internal oscillator or by external pulses which may be connected to the two 4mm sockets mounted on the rear panel of the instrument. Example of the many applications of this unit are to be found in motion analysis multi exposures photography, examination of moving parts and measurement of rotational speed.
Specifications:-
Input Volts : 220V AC, 50 Hz
Flash Rate: 0- 9999 Flashes per minute.
Resolution : 1
Display: 7 Segment LED (4 nos.)
Tangent Galvanometer
XTEMOS ELEMENT
AJAX PRODUCTS TABS ARROWS PAGINATION
Human Tooth, Upper Triple Root In 2 Parts
IoT Gateways
5KVA IGBT Based Converter Inverter System
DC Motor Specification
• Power : 3HP • Armature voltage : 220V DC • Field voltage : 220V DC • Speed : 1500 RPM • Make : Benn • Double side shaft extensionSlip Ring Motor
• Type : 3phase slip ring induction motor. • Power : 2KW • Stator voltage : Three phase 415V AC, 4A • Rotor voltage : Three phase 210V AC, 6A • Speed : 1410 RPM • Make : BenndsPIC 30F4011 based PWM Controller
• Microchips’ dsPIC30F4011 16 bit digital signal controller operating at 20MIPS • On chip 48K Bytes flash program memory • On chip 1K Bytes data EEPROM • On chip 2K Bytes RAM • Four Compare/PWM output • Six PWM output for Motor control • One 3 channel Quadrature Encoder interface circuit/4 capture input • 9 Channels 10 bit ADC of 500Ksps conversion tune. • One RS232 Compatible serial port Opto isolated & terminated at 9 pin D male connector • 6 PWM outputs and two capture inputs and two compare outputs are terminated at 34pin FRC connector. • 4 Channels of DAC output & 5 channels of ADC inputs are terminated at 26 pin FRC connector • 16 x 2 alphanumeric LCD displayXTEMOS ELEMENT
AJAX PRODUCTS TABS WITH ICONS
Curved Member Apparatus
Apparatus consists of a steel bar which is used to make the different curved members Viz. circle, semicircle with straight arm, a quadrant of a circle and quadrant of a circle with straight arm. The bottom ends of the members are fixed to the base. Under the application of load at free end, its horizontal and vertical deflection can be measured with the help of dial gauges. A dial gauge with 25mm travel (with a magnetic base) is supplied with the apparatus. Apparatus to be supplied should be complete with a supporting stand and a set of weights.
Experimental Capabilities: Apparatus is supplied complete with a supporting stand and a set of weights.
SPIRIT LAMP
Human Physiology Charts
Description
Poly art Charts are multi colored, accurate in details, printed on plastic, laminated on both sides, washable, non-tearable and long lasting with plastic rollers, size 75 x 100 cm. Skeletal System Muscular system Circulatory system Nervous system Digestive system Teeth & skin Human eye, ear & head Lymphatic system Respiratory system Endocrine system Nutrition Immune system Human Nose Human Heart Excretory system Human Eye Human Ear Human Kidney Human Lungs Human Liver
Hydraulic Disc Brake Actual Working
XTEMOS ELEMENT
AJAX PRODUCTS TABS LOAD MORE PAGINATION
SILICA CRUCIBLE WITHOUT LID
PRODUCT DESCRIPTION
- Crucible is glazed inside and outside.
- Highly resistant to alkalis and hot temperatures
- 50ml capacity
- Outside diameter 55mm, 42mm height
- No lid includedSilica crucible is glazed inside and outside. Highly resistant to alkalis and hot temperature SIZES ARE: 15ML 25ML 50ML 80ML 100ML 150ML
SILICA CRUCIBLE TALL FORM Without Lid, Translucent
XTEMOS ELEMENT
AJAX PRODUCTS TABS CAROUSEL
Laboratory Spatula
Acquire from us high quality Laboratory Spatula at affordable price range.
Moulded in Polypropylene, Spatula consists of a spoon on one side while the other end is a flat construction with a knife edge.
This is helpful in breaking up crystals of different salts while the spoon is used to draw salts from the containers.
| Particulars | Pack (Pcs) | |
|---|---|---|
| Spatula 150 mm | 12 | |
| Spatula 200 mm | 12 |
Mechanical Heat Pump Trainer
Heat Pump is a device to pump heat from one source to another. The heat obtained by heat pump is more than that could be obtained by direct electrical heating. The apparatus consists of refrigeration system with water cooled shell and coil type evaporator and condenser.
SPECIFICATIONS:
1.Compressor – Hermetically sealed compressor using R-12 refrigerant, having capacity 0.3 tons of refrigeration. Condensing pressure – max. 15 Kg/cm2 (Actual pressures will depend upon working conditions). 2.Condenser – Shell and coil type with continuous water flow arrangement. 3.Evaporator – Shell and coil type with continuous water flow arrangement. 4.Expansion Valve – Internally equalized thermostatic expansion valve. 5.Measurements – a) Rotameter for condenser & evaporator water flow rate measurement. b) Rotameter for liquid refrigerant flow measurement. c) Pressure gauges for condensing and evaporating pressure – 2 Nos. d) Thermometer for refrigeration cycle & water temp, measurement – 7 e) Wattmeter for compressor input measurement. f) Ammeter for compressor current measurement. 6.Controls – a) HP/LP cutout for compressor. b) Overload protector for compressor. c) Gate valve to control water flow rates. d) Necessary switches and fuse. A technical manual is accompanies the unit.SERVICES REQUIRED:
1.Floor surface area – 2m, X 2m. X 1.5m. height. 2.220V. 15Amp. Single Phase Stabilized power supply.
Turbine/Pump Unit
Description
For use as a water turbine to drive a generator producing electricity or for use as a pump driven by a motor and raising a head of water to produce potential energy. The rotor has eight 'bucket' blades and is housed in a block turbine chamber with a clear Perspex front. Two inlet tubules (for turbine and pump operation respectively) and one outlet tubule are provided and the shaft carries a 15 mm. diameter pulley. With driving belt.
Aves
Description
All Charts are made on PVC rexine, hand drawn, waterproof, in fast multi colors with a black background. Each chart is provided with rollers to hang on wall, Size 75×100 cm. Pigeon External Character Pigeon Internal Anatomy Pigeon Skeleton Pigeon various systems Fowl Skeleton Chick Development Chick embryo 16 Hours Chick embryo 24 Hours Chick embryo 27 Hours Chick embryo 30 Hours Chick embryo 43 Hours Chick embryo 48 Hours Chick embryo 56 Hours Chick embryo 72 Hours Chick embryo 96 Hours Beaks of Birds Claws of Birds Types of Birds
