XTEMOS ELEMENT
AJAX PRODUCTS TABS
Slip Creep Measurement Apparatus
The apparatus consists of a variable speed D.C. Motor, Driving pulley and Driven pulley of equal diameter. The pulleys are mounted on input shaft (Motor shaft) and output shaft. The driven pulley can slide on the base with bearing block to change initial tension in belt. Brake drum is mounted on output shaft helps to measure power output. The motor speed is varied by dimmerstat. A two channel RPM Indicator is provided to measure speeds of driven and driving pullies respectively.
Specifications:
1.D.C. Motor – 1 HP, 1500 RPM, variable speed. 2.Driving & Driven puilies of equal diameters. 3.Brake drum along with spring balance. 4.Fiat Belt of fixed length of following materials – (i)Fabric Belt (ii)Canvas Belt. (iii)Rubber Belt. 5.Belt tightening arrangement. 6.Speed Controller unit. 7.Two Channel digital RPM Indicator. 8.Stroboscope.Experimentation –
1. To measure co-efficient of friction between pulley material and different belt materials. 2. To measure power transmitted with varied belt tensions and plotting graph of (T1 – T2).Tension Characteristics. 3. To measure percentage slip at fixed belt tension by varying load on brake drum and plot graph of (T1-T2) Vs.percentage slip.i.e. Slip Characteristics. Finding a creep zone from graph. 4. To measure belt slip speed and observe the limiting value float at constant speed when the slip just starts.Service Required:
1.230 V.A.C. stabilized power supply 2.Space -. 1.5m x 1.5 m.
Blood Collection Vials (VACUTAINER) Plain/EDTA
Blood collection and storage is done is special tubes which allow the preservation of the blood sample over long periods.
These tubes can be made of glass or plastic and the caps of these vials are coloured to indicate the additives in them.
Some of the additives are anticoagulants such as EDTA, sodium citrate or heparin.
Other substances include preservatives. The containers containing coagulants are capped with gold, red or orange caps.
The ones containing anti-coagulants are green, which contain heparin, purple or lavender indicates ones which contain EDTA, grey capped tubes contain sodium fluoride or oxalate. Blood collection tubes (also called as vacutainers) are extensively used in hospitals, medical centres and diagnostic centres.
In biological labs, it is used in experiments like haemolysis etc.
Non Vacuum Vials (Pk of 100)
Vacuum Vials (Pk of 100)
Charle’s Law Kit
XTEMOS ELEMENT
AJAX PRODUCTS TABS SIMPLE
Burettes with Rota Flow Stopcock (BG)
Hydraulic Bench Apparatus
OBJECTIVE:
To conduct the experiment of hydraulic bench, with separate experiential set ups i.e. Hydrostatic Pressure, Flow over Weirs, Bernoulli’s Theorem, Flow meter Demonstration, Impact of jet and Orifice Discharge etc. which are accessories of the Hydraulic Bench.DESCRIPTION OF APPARATUS:
The set up is a self-contained, water recirculation unit provided with a top tray, sump tank and a measuring tank. Drain valve and over-flow are provided on the sump tank. A centrifugal pump is fitted for water circulation. Flow control valve and bypass valve is fitted in water line to conduct the experiment at different flow rates. Flow rate of water is measured with the help of measuring tank and stop watch. Measuring tank is provided to measure the discharge. Drain valve is provided in the measuring tank to empty water in sump tank after measuring discharge. Separate level indicator and scale is provided to read the level of water in the measuring tank.UTILITIES REQUIRED:
1.Water Supply (Fill approx 250 Ltrs Initially). 2.Drain Required. 3.220 V AC, 50 Hz, single phase electric supply source. 4.Floor area 1.75 m x 1.50 m.SPECFICATION:
1. Top Tray : 1060 mm x 650 mm. 2.Pump : 1 HP 3.Flow Measurement : Using measuring Tank (Material SS) 4.Tank : Capacity 40 Ltr. 5.Sump Tank : Capacity 120 Ltr. Material SS. The whole set-up is well designed and arranged in a good quality powder coating painted structure.
Bar & Gauge
XTEMOS ELEMENT
AJAX PRODUCTS TABS ALTERNATIVE
Fashion
Dead Weight Pressure Gauge Tester
DESCRIPTION:-
Dead weight Pressure Gauge Tester is manufactured to measure the Pressure gauge up to the capacity of 25kg/cm2.The system is nickled chrome to protect from rust. The weights are Zink Iron for long term use.EXPERIMENTS:-
• Study of the hydrostatic force on a plane surface under different submerged conditionsFEATURES:-
• Superb Painted structure • Simple to operate & maintainUTILITIES REQUIRED:-
• Machine Oil.SPECIFICATION:-
• Bourdon tube pressure gauge as manometer • Manometer with transparent scale • Manufactured from corrosion resistant materials • Components arranged on base plate. • Set of weights • Medium for transmitting pressure: hydraulic
Concentric Tube Heat Exchanger
(A)Plain Tube ( Water To Water ):
The apparatus consists of two concentric tubes. Inner tube consists of copper tube through which hot water flows. While the outer tube consists of GI pipe through which cold water flows. The arrangement enables the parallel and counter flow of the cold water. The inlet and outlet temperatures and the flow measurement enable to find out the heat exchanged LMTD, and effectiveness of the equipment.
Specifications:
1.Inner copper tube I.D, 12.7mm. and outer G. I. Pipe I. D. 15mm. approx. and 1.5m. length. 2.Thermometers – 4 nos. 3.Measuring flask – 1 Lit. capacity. 4.Geyser-3 kW. Single phase.Services required
1.220v, 15A, stabilized single-phase AC supply. 2.Floor area – 3m x I m x 1 m height. (B) Finned Tube ( Water To Air ): The apparatus consists of two concentric tubes. Inner tube consists of copper tube through which hot water flows. It is finned at its outer diameter to increase the heat transfer surface. While the outer tube consists of GI pipe through which cold air flows. The arrangement enables the parallel and counter flow of the air. The inlet and outlet temperatures and the flow measurement enable to find out the heat exchanged LMTD, and effectiveness of the equipment.Specifications:
1.Inner copper tube I.D. 12.7mm. and outer G. I. Pipe I. D. 25mm. approx. and 1m. length. 2.Thermometers – 4 nos. 3.Orifice meter along with manometer. 4.Measuring flask – 1 Lit. Capacity. 5.Geyser-3 kW. Single phase.Services Required
1.220v, 15A, stabilized single-phase AC supply. 2.Floor area – 3m x 1m x 1m height.XTEMOS ELEMENT
AJAX PRODUCTS TABS ARROWS PAGINATION
Kidney With Bladder
Moving Coil Multi Range Meter
Description
For DC & AC current and voltage. The operation of these meters depend on the reaction of the current circulating in the moving coil and a field of a fixed permanent magnet. Considering the operational nature and design of these instruments. the scale is linear. Since, the direction of the movement rotation depends on the direction of the current flow (polarity) in the circuit. The moving coil multirange meter can be used on direct current circuit and also alternating current with a suitable rectifier inserted in the circuit.| Accuracy | DC + F.S.D. & AC + 2.5 F.S.D. |
| Scale Length | 60 mm approx. with knife edge pointer and anti parallel mirror scale. |
| Dial Size | 80x80 mm, rectangular. |
| Moving Coil Multirange Voltmeter has following ranges | DC & AC 0-5 - 25 - 50 - 100 - 250 - 500V |
| Moving Coil Multirange Ammeter has following ranges | DC & AC 10 mA - 100mA - 500 mA - 1A - 2.5A - 5A |
XTEMOS ELEMENT
AJAX PRODUCTS TABS WITH ICONS
Leaf Area Meter
Description
Leaf Area Meter We have been affianced in offering an exclusive collection of Leaf Area Meter which is used to obtain measurements of leaf area without detaching the leaf from the plant. The offered meter is manufactured with the use of high grade components and latest tools in order to meet the set industry standards. These are extensively used for conducting various tests and studies on the leaves of a tree.
CRUCIBLE TONG (STAINLESS STEEL)
Ticker Tape Timer 12V
Ticker Tape Timer 12V
These devices use an electromagnet which activates a striker, producing dots via a carbon disk on the ticker tape.
With 4mm terminal sockets.
The dots are produced at a rate of 50 - 60Hz depending on the mains frequency.
There are 6V and 12v units available.
The Ticker Tape Timers are used in the measurement of velocity, acceleration and general timing.
XTEMOS ELEMENT
AJAX PRODUCTS TABS LOAD MORE PAGINATION
SILICA CRUCIBLE WITHOUT LID
PRODUCT DESCRIPTION
- Crucible is glazed inside and outside.
- Highly resistant to alkalis and hot temperatures
- 50ml capacity
- Outside diameter 55mm, 42mm height
- No lid includedSilica crucible is glazed inside and outside. Highly resistant to alkalis and hot temperature SIZES ARE: 15ML 25ML 50ML 80ML 100ML 150ML
SILICA CRUCIBLE TALL FORM Without Lid, Translucent
XTEMOS ELEMENT
AJAX PRODUCTS TABS CAROUSEL
Fuel Supply System Petrol MPFI Type
Fuel Supply System Petrol MPFI Type (Actual Working Model) Multi Point Fuel Injection
This is an actual working model of fuel supply system of a MPFI petrol engine. The parts details is as under :
1. Fuel Tank
2. Fuel Filter
3. Motorised Fuel Pump
4. Pressure Gauge
5. Fuel Rail
6. Fuel Injectors
7. ECU
8. Igniter & Ignition Coil
9. Distributor
10. Spark Plugs
11. Power Supply
12. Fuel Gauge & Control Panel
This model helps the student to understand about the parts & working of MPFI system. It is specially designed for demonstration purposes. The model will be supplied with key card & very interesting literature regarding working.
Induction Coil, Ruhmkorff
Description
Coils are wound with highly insulated copper wire impregnated with paraffin wax; input 6-8 V dc through two 4 mm socket terminals, with an adjustable trembler system. The spark suppression capacitor is housed in the base. A pair of pointer electrodes with insulated handles for adjustment of the spark gap is provided. Spark length 10 mm Spark length 25 mm Spark length 50 mm Spark length 75 mm Spark length 100 mm
Shell Tube Heat Exchanger Water To Water
Heat exchanger is the devices used to transfer the heat from one fluid to other. The shell and tube heat exchanger is two tube single pass heat exchanger. The hot fluid is hot water obtained from water heater. The coil fluid is cold water. The schematic flow arrangement is shown in figure. Hot water enters the lower side of end box, flows through the tubes in lower half of shell and comes to the other end of the shell. It reverses its direction, flows through tubes in upper half of the shell and leaves out. Cold water enters lower part of the shell passes over the tubes between the baffles and leaves out the shell through outlet at upper surface of shell.
