XTEMOS ELEMENT
AJAX PRODUCTS TABS
Demonstration Gear Model System
Description
A series of models to demonstrate different gearing systems. With transparent slideplates, the gears may easily be seen and where necessary there is an index on the primary and secondary shafts to show the change in the direction of rotation and the relative speed of rotation. A simple three-speed and reverse-gear system using spur gears. Reverse gear is obtained by interposing a small lay-shaft mounted pinion between the two main shafts. Gear selection is by means of a short ball-ended lever.
Model of Terrestrial Telescope
XTEMOS ELEMENT
AJAX PRODUCTS TABS SIMPLE
MCS Family Microcontroller Trainer
Specification
• 89C51 Microcontroller operating at 12Mhz • 64KB on-chip internal Flash EEPROM program memory • 1KB on-chip data RAM • 64KB External Data RAM • 32KB EPROM for monitor program • 32KB RAM for Program/Data memory • 32KB RAM for data memory • 1KB On-Chip Data RAM • Battery backup for RAM • Onboard 16 x 2 Alphanumeric LCD Interface • Onboard IBM PC Keyboard Interface • RS232/RS485 compatible serial interface terminated at 9 pin 'D' male connector • One RS232 Cable • Onchip Programmable Counter Array (PCA) PCA Contains five 16 bit PWM/capture/compare output • 48 TTL I/O lines using 8255 terminated in two 26 Pin FRC Connectors • All CPU address, data, and control signals are terminated in a 50 pin FRC Connector (VXT Bus) for connecting the • VBMB series of Experiment boards. • All connections of the Microcontroller are terminated in a separate connector for expansion • Built-in Line assembler & Disassembler • Windows based In System Programming Software for Flash Memory programming
Agate Mortar & Pestle
Description
We offer Agate Mortars & Pestles under the brand name of Adarsh International. These Mortars & Pestles are made of naturally occurring Agate Stone, which essentially is an amorphous form of ADARSH. Due to its inherent physical characteristics our Agate Mortar & Pestle it is quite hard. The hardness on the Moh's scale is 6.5. Adarsh Brand Agate Mortars & Pestles are recommended for use in laboratories demanding contamination-free results.Diameter Sizes
1. Dia 2" 2. Dia 2.5" 3. Dia 3" 4. Dia 4" 5. Dia 5"
Human Nose, L. S.
Ice Plant Trainer
The Plant uses ice can system. The cans filled with fresh wafer are kept in a tank in which brine is circulated. The brine is cooled by the refrigerant, which in turn cools the water in can and ice formation takes place.
SPECIFICATIONS:
1.Compressor : Kirioskar make hermetically sealed compressor using R 12 Refrigerant. 2.Condenser : 4 row type air cooled. 3.Expansion Valve : 0.5 TR capacity. 4.Evaporator : 1/2″ O.D. copper tube – 75 feet long. 5.Filter – Drier : Silica gel filled – 3/8″ flare connections. 6.Main Tank : 600 mm X 375 mm 7.Total Ice Cane Capacity : 7 Kg 8.Ice Making Capacity : 7 Kg / 4 Hours. 9.Thermocol insulation : 6.5″ 10.Brine Stirrer : Motor driven fan, 1 phase, 1/10 HP, 1440.INSTRUMENTATION:
1.Temperature Indicator : Digital Type O300°c, with 1 °c least count, using Cr/Al thermocouples. Accuracy 1 % of full reading. 2.Compressor Energy Meter : Single Phase, 10 – 20 Amp. Capacity. 3.Pressure Gauge: a)0-21 Kg/cm2 b) -1 to 10.6 Kg/cm2 c) Both of 65 mm dial. 4.Digital Thermometer CONTROLS : 1.HP/LP Cutout : Auto reset type. 2.Thermostat : Auto reset type. A technical manual accompanies the unit.SERVICES REQUIRED:
1.Floor Area – 2m. X 1.5m. X 1.5m. Height. 2.220 V., 15 Amp.Single Phase Stabilized power supplyXTEMOS ELEMENT
AJAX PRODUCTS TABS ALTERNATIVE
Fashion
Manual Steering System
Steering System – Actual Working
Manual Steering System
The working of steering system is shown with the help of actual parts assembled on square iron pipe frame. All the necessary parts of steering system are shown in actual working form. This model helps the student to understand the working of the steering system very easily. It is specially made dissectible for demonstration purposes.
L Shaped Spreader
We are a prominent Exporter & Trader of L Shaped Spreader.
The L Shaped Spreader is sterile & smooth and enables even spreading of liquid samples across the surface of a jar plate without grouping & cutting the medium.
Avail the L Shaped Spreader from us at nominal market prices.
Material : Polypropylene
| Particulars | Pack (Pcs) | |
|---|---|---|
| L Shaped Spreader | 100 | |
| Micro Pestle (for 0.5 and 1.5 ml MCT) | 12 | |
| Micro Pestle (for 1.5 ml MCT) | 12 |
Universal Multi Rack
Avail from us high quality Universal Multi Rack at affordable price range.
Souced from reliable vendors, this rack is an excellent lab apparatus compatible with different sizes of tubes.
Four sides of this rack can be used for tubes of 30mm, 20mm, 17mm & 12mm.High grade Polypropylene is used for its manufacturing.
Material : Polypropylene
| Particulars | Pack (Pcs) | |
|---|---|---|
| Universal Multi Rack | 6 | |
| Rotatable Multi Rack | 1 |
XTEMOS ELEMENT
AJAX PRODUCTS TABS ARROWS PAGINATION
Abney Level
Description
The Hand Level is a small, economical level for use with preliminary surveys to determine traveller way or cable way steel work elevations and other feasibility type site reconnaissance work. The Abney Level is very similar to a clinometer in that it is used to measure the value of a slope by means of arc measure and grade percentage.Specification of Abney Level
• Used to determine slope angle, tree heights etc • Graduated 0-+/-90 degrees, 0-+/-100% on a stationary arc • Vernier reads to 10 • Scale pointer incorporates friction thumb lock • Includes carry case
Blood Collection Vials (VACUTAINER) Plain/EDTA
Blood collection and storage is done is special tubes which allow the preservation of the blood sample over long periods.
These tubes can be made of glass or plastic and the caps of these vials are coloured to indicate the additives in them.
Some of the additives are anticoagulants such as EDTA, sodium citrate or heparin.
Other substances include preservatives. The containers containing coagulants are capped with gold, red or orange caps.
The ones containing anti-coagulants are green, which contain heparin, purple or lavender indicates ones which contain EDTA, grey capped tubes contain sodium fluoride or oxalate. Blood collection tubes (also called as vacutainers) are extensively used in hospitals, medical centres and diagnostic centres.
In biological labs, it is used in experiments like haemolysis etc.
Non Vacuum Vials (Pk of 100)
Vacuum Vials (Pk of 100)
Variable Inductor
Description
The enamelled wire winding and a cylindrical soft iron core are built into this unit. The iron core displacement inside the winding can manually adjusted by the knob to give precise measurements up to 1.3 H. Connections are made through 4 mm sockets.Specifications:
Resistivity: 0.0165 W/m; Inductance: 0.15 to 1.3 H; Voltage: 30 V AC or 60 V DC.XTEMOS ELEMENT
AJAX PRODUCTS TABS WITH ICONS
Plant Mitosis
Trans-Ratio
Description
Trans-Ratio is a simple transformer system that allows students to investigate the relationship between primary voltage, secondary voltage and the turns ratio. The Primary coil has tappings at 200, 400 and 600 turns while the Secondary has 100, 200, 300, 400, 500 and 600 turns all brought out to 4mm sockets. An AC supply of upto 6 V as well as AC voltmeters are required for demonstration purpose.
Direction of Current
Magnetic Field Apparatus
XTEMOS ELEMENT
AJAX PRODUCTS TABS LOAD MORE PAGINATION
SILICA CRUCIBLE WITHOUT LID
PRODUCT DESCRIPTION
- Crucible is glazed inside and outside.
- Highly resistant to alkalis and hot temperatures
- 50ml capacity
- Outside diameter 55mm, 42mm height
- No lid includedSilica crucible is glazed inside and outside. Highly resistant to alkalis and hot temperature SIZES ARE: 15ML 25ML 50ML 80ML 100ML 150ML
SILICA CRUCIBLE TALL FORM Without Lid, Translucent
XTEMOS ELEMENT
AJAX PRODUCTS TABS CAROUSEL
Seven Segment LED Display Circuit
A common anode seven segment module is fitted on a board with 8 bit dip switch to control the each segment of seven segment LED display. The inputs A-D of a display driver are connected to the binary coded decimal (BCD) outputs from a decade counter. A network of logic gates inside the display driver makes its outputs a-g become high or low as appropriate to light the required segments a-g of a seven segment display. A resistor is required in series with each segment to protect the LEDs
Car Chassis Rear Wheel Drive Actual Cut Section Motorised
Car Chassis Rear Wheel Drive Actual Cut Section – Motorised
4 Stroke 4 Cylinder Petrol Engine With Clutch, Gear Box, Propeller Shaft, & Rear Axle Assembly With Differential Gear
The chassis of the four stroke four cylinder engine cut section model. The cut section model is constructed such that all the following systems can be demonstrated in working conditions.
ENGINE:
Maximum parts and accessories of an engine like cylinders, cylinder head, inlet and Exhaust manifolds, FIP, injectors, self-starter, alternator, water pump, radiator, etc., are sectioned to show the internal constructional details. The complete sectioned model is coupled with FHP 220/230V A.C single phase motor through a Reduction drive unit.TRANSMISSION SYSTEM:
This system consists of a Clutch and four speed gearbox assembly, the casing of which is suitably cut to demonstrate its operation. The gearbox is coupled to Differential gear box with propeller shaft and the different coupling used for this transmission can be demonstrated. The Differential gear box is also cut so as to clearly to demonstrate its complete operating principle. The gear shifting including the forward and reverse gear operation can be clearly shown. The speed variation and the rotation of the Differential gear box can be seen while gear shifting. By running the motor connected to the engine assembly the entire system with gear box, rear axle etc. can be demonstrated in running. FUEL SYSTEM: The Fuel tank is cut to expose the mounting of the level sensor and the position of Fuel section. The system is complete with mechanical Fuel pump. EXHAUST SYSTEM: It consists of Exhaust Manifold and silencer in cut section to explain internal construction. LUBRICATION SYSTEM: It consists of the engine Lubrication system along with the Lubrication oil pump is suitably sectioned. SUSPENSION SYSTEM: This will explain both the Hydraulic Suspension systems at the front and the leaf spring Suspension at the Rear. One of the hydraulic arrangements of Suspension mechanism is highlighted (with shock absorbers) and explained cut sectionally.BRAKING SYSTEM:
The Hydraulic or Air circuit Brakes. The movement of the Brake Shoes on operating the brake pedals can be seen in the area where the Brake drum is cut. The front and rear brakes will be operational. STEERING MECHANISM: The can be seen and included in the Steering wheel. Steering gear box and coupling of the same to the wheels will be shown by rotating the steering wheel, the operation of the steering system can be demonstrated. The entire system will be mounted on the chassis, and suitable mounting option with caster wheels will be provided for easy movability.
Signal Generator, Digital
This signal generator is a useful test instrument capable of generating multiple waveform and offers excellent waves shape, signal linearity, waveform symmetry and frequency range with selection of sine, triangular and square wave and amplitude variable 10 V peak to peak. 1 Hz to 100 kHz in five decade ranges selected by rotary switch named as frequency multiplier. Sine, triangular and square waveforms selected by push switch with LED indication. Output signal is 0 – 3.5 Vrms (10 V peak to peak) open circuit continuously control with uncalibrated amplitude control knob. Mains rocker switch with indicator Light. Signal Generator is versatile for general laboratory use; output signal is adjustable with the combination of frequency multiplier and set frequency dial with a low level of distortion. Set frequency is displayed on a 4 seven segment display. Output Voltage is continuously variable with selector range 1 V and 10 V.There is two pair of output safety sockets. One for CRO output (experiment for amplification, filter etc.) and another pair of sockets to speaker to drive a speaker and to demonstrate the audio signal frequency range 20 Hz to 20 KHz.
Deflection Of Truss Apparatus
Apparatus consist of 4 panels of a PRATT steel truss, each panel being 40cm in horizontal direction and 30cm in vertical direction. Load can be applied on each panel point. All tension members should be provided with detachable springs so as to obtain appreciable deformation of the member. Direction of the diagonal members may be changed. Apparatus can be used to illustrate visually the nature of forces set up in various members of the Truss. Apparatus to be supplied should be complete with a supporting stand and a set of weights.
Experimental Capabilities: Apparatus is supplied complete with a supporting stand and a set of weights.
