XTEMOS ELEMENT
AJAX PRODUCTS TABS
TMS320VC5416 Based DSP Trainer
This Kit provides new performance enhancing Features such as USB Communications. This is Suitable for applications that require optimized Combination of Power Performance & area. Suitable for the range of Signal processing applications, including speech Compression / decompression Speech recogniation, echo generation and Cancellation.
ON-CHIP FEATURES:
• 160MIPS Performance, can operate upto 160MHz • Advanced multi bus architecture with one program bus, three data buses and four address buses • 40-bit arithmetic logic unit (ALU), including a 40-bit barrel shifter and two independent 40-bit accumulators • 17-bit × 17-bit parallel multiplier coupled toa 40-bit dedicated adder for non pipelined single-cycle multiply/accumulate (MAC) operation. • Compare, select, store unit (CSSU) for the add/compare selection of the Viterbi operator • Exponent encoder to compute the exponent of a 40-bit accumulator value in a single cycle • Two address generators, including eight auxiliary registers and two auxiliary register arithmetic units.ON-BOARD FEATURES:
• 4 Mbit (256Kb x 16) Flash Memory • 4 Meg (256K x 16-Bit) Static RAM for External Program/Data • 8 way DIP switch & LED • ON Board JTAG Emulator (XDS 100 version - 2) • PCM3002 AUDIO CODEC • Expansion connector for GPIO & Peripheral interface • On board USB for serial communication
Thermo Hygrograph
Description
Thermo Hygrograph with Special the range of -15 deg.C to +65 deg.C and RH 0-100% with Meachanical Winding Clockwork, Weekly and/or Daily Rotation Recording(Changeable) with German Fibre Tips or with Nibs. Thermo Hygrographs are used for Environmental control, Labs, Research, Agricultural institutes, Plants, Scientific, Textile Mills, Meteorology and other Industries. Specifications: Temperature -15°C to +65°C Relative Humidity 0-100% Housing made of cast aluminum and chrome steel white finish Glazing made of transparent synthetic material.
Voltaic Cell Set, Student
XTEMOS ELEMENT
AJAX PRODUCTS TABS SIMPLE
Soil Auger
CNC Lathe Trainer Slant Bed
CONTROLLER:
Type of control system : PLC based system Axis motor and drive : Servo motor & drive with feedback Input ti servo : Optically lsolated Motor Drive : TTL compatible Interpolation : Linear/Circular /parabolic Cycles Used : G, M, S, T, F, I, K, M, F, Cycles : Circular interpolation / Canned Threading : Straight / Taper Power Devices : Short Circuit and over Temperature Protected, Single Phase Protection Real Time Toolpath Simulation : providedMACHINE DETAILS:
Center Height : 100mm Swing over Carriage : 80mm Distance between Centre : 825mm Weight : 700kg Dimension in mm : 1250 x 900 x 1500 Rapid Travel : 700mm/min Resolution Z Axis : 5micron Resolution X Axis : 5micron (Dia.) Automatic Lubrication : provided Tool Changer : Automatic – 8 stationSPINDLE:
Spindle Speed : Continuous Variable Spindle power : 2HP Inside Taper : MT3 Speed Range : 100 to 3000 RPMAXIS TRAVEL:
X Axos : 100mm Z Axis : 300mm
Pteridophyta
| Azolla Sporocarp VS | Adiantum Rhizome TS |
| Adiantum Root TS | Adiantum Sorus VS |
| Equisetum Prothallus WM | Equisetum Root TS |
| Equisetum Rhizome TS | Equisetum Stem TS |
| Equisetum Cone TS | Equisetum Cone LS |
| Fern Rhizome TS | Fern (Pteris) Prothallus Young |
| Fern Prothallus with Antheridia | Fern Prothallus with Archegonia |
| Fern Prothallus with Sporophyte | Fern Leaf with Sori TS |
| Fern Sori WM | Fern Prothallus TS |
| Fern Rachis TS | Fern Root TS |
| Lycopodium Root TS Lycopodium Stem TS | Lycopodium Apex LS |
| Lycopodium Cone LS | Lycopodium Cernum Stem TS |
| Lycopodium Wightiatum Stem TS | Lycopodium Phlegmaria Stem TS |
| Marsilea Leaf TS | Marsilea Root TS |
| Marsilea Rhizome TS | Marsilea Petiole TS |
| Marsilea Sporocarp LS | Marsilea Sporocarp TS |
| Selagineela Root TS | Selaginella Rhizophore TS |
| Selaginella Leaf TS | Selaginella Stem TS |
| Selagineela Strobilus WM | Selaginella Strobillus LS |
| Selaginella Microsporangia WM | Selaginella Mega and Microsporangia WM, TS |
Friction In Pile Lines Apparatus
DESCRIPTION:-
The Set-up consists of 2 pipes of different diameters, which are connected in parallel. Pressure tapings are provided on each pipe to measure the pressure losses with the help of a Differential Manometer. Control valves are fitted on each pipe, which enables to use one pipe at a time for experiment. Present set-up is self-contained water re-circulating unit, provided with a sump tank and a centrifugal pump etc. Flow control valve and by-pass valve are fitted in water line to conduct the experiment on different flow rates. Flow rate of water is measured with the help of measuring tank and stop watch.EXPERIMENTS:-
Ø To determine the losses due to fiction in pipes Ø To determine the friction factor for Darcy Weis back equationUTILITIES REQUIRED: –
Ø Water Supply & Drain Ø Electricity Supply: Single Phase, 220 VAC, 0.5 kWTECHNICAL SPECIFICATION: –
Ø Pipes (2 Nos.) : Material GI of ½ “ & 1” Diameter Ø Pipe Test Section : Length 1 m Ø Water Circulation : FHP Pump, Crompton / Sharp make Ø Flow Measurement : Using Measuring Tank with Piezometer,Capacity 25 Ltrs. Ø Sump Tank : Stainless Steel, Capacity 50 Ltrs. Ø Stop Watch : Mechanical / Electronic Ø Control Panel : On / Off Switch, Mains Indicator etc. The whole Set-up is well designed and arranged in a good quality painted StructureXTEMOS ELEMENT
AJAX PRODUCTS TABS ALTERNATIVE
Fashion
Magenta Box
Magenta Box is very often used in tissue culture & agricultural research experiments.
Main body of this Magenta Box is made of tough & transparent polycarbonate which provides excellent view of the contents inside while the cover is made of Polypropylene.
This autoclavable Magenta Box is square in shape giving itself a space saving features.
| Particulars | Pack (Pcs) | |
|---|---|---|
| Magenta Box | 12 |
BOD Incubator
Specification
BOD Incubator is designed for low temperature incubation and determination of Bio Chemical Oxygen Demand (B.O.D). The BOD Incubator comes with a double wall construction. The Inner chamber is made of richly anodized aluminum or highly polished stainless steel with two / three removable perforated shelves. The exterior chamber of the BOD Incubator is made of thick mild steel sheet duly finished in enamel paint. Outer double wall door is provided with magnetic gasket and lock & key arrangement. The inner door is made out of clear acrylic sheet allowing inspection of material in the chamber without disturbing the chamber temperature. Door operated inner illumination has been provided. The gap between walls of equipment are filled with glass wool for temperature insulation. The cabinet is mounted on castors. The temperature in the BOD Incubator is controlled by a sensitive thermostat from 5oC to 50oC ± 1oC. For lower temperature working, a standard cooling unit with sealed compressor with protective devices has been provided below the chamber for safe and efficient working. Heating arrangement has made within the chamber for higher temperature. Inner air circulating system is provided to achieve uniform temperature in the whole chamber.| Inner Chamber Size | Cap. | Material |
|---|---|---|
| 455 x 410 x 610 mm | 4cu. Ft. or 112 Ltr. | Aluminium |
| 455 x 410 x 610 mm | 4cu. Ft. or 112 Ltr. | S.S. |
| 505 x 451 x 830 mm | 6cu. Ft. or 171 Ltr. | Aluminium |
| 505 x 451 x 830 mm | 6cu. Ft. or 171 Ltr. | S.S. |
| 565 x 565 x 865 mm | 10cu. Ft. or 280 Ltr. | Aluminium |
| 565 x 565 x 865 mm | 10cu. Ft. or 280 Ltr. | S.S. |
Optional
Timer 0-24 hours day night cycle. Internal illumination with 3 fluorescent tubes. Digital temp. Indicator-cum-Controller.
Amplitude Modulation And Demodulation
Instrument is design to demonstrate the method to transmit signals via. Electromagnetic transmission. It is still used in radio system to transmit audio signal although it has lesser in popularity compared to FM (Frequency Modulation) due to its lower signal to noise ratio.
Technical Specification :-
1. I C based DC regulated Power Supply ±12 V / 500 mA.
2. Audio frequency 1 KHz / 0-2 Vpp for modulating signal 455 KHz / 2.5 Vpp approx. for Carrier Frequency.
XTEMOS ELEMENT
AJAX PRODUCTS TABS ARROWS PAGINATION
Burner Bunsen, LPG
Mock Layout Of Car Wiring Latest Type
Mock Layout Of Car Wiring Latest Type
All the components used in the apparatus are of modern car. The complete mock layout is beautifully divided into 5 sections as under
(A) Front Lighting Panel
(B) Dash Board Panel
(C) Ignition System
(D) Rear Lighting Panel
(E) Motorised Charging System
With the help of this mock layout system its becomes very easy for the students to understand the actual working of electrical system of a modern car.
Study Of Pipe Fitting
DESCRIPTION:-
The Set-up consists of a ½ bend and elbow, a sudden expansion & sudden contraction fitting from 15 mm to 25 mm, ball valve and gate valve. Pressure tapings are provided at inlet and outlet of these fittings under test. A differential manometer fitted in the line gives pressure loss of individual fitting. Present Set-up is self-contained water re-circulating unit, provided with a sump tank and a centrifugal pump etc. Flow control valve and by-pass valve are fitted in water line to conduct the experiment on different flow rates. Flow rate of water is measured with the help of measuring tank and stop watch.EXPERIMENTS:-
Ø To determine loss of head in the fitting at various water flow rates. Ø To measure the loss co-efficient for the pipe fittings.UTILITIES REQUIRED: –
Ø Water Supply and Drain Ø Electricity Supply: Single Phase, 220 V AC, 0.5 kW.TECHNICAL SPECIFICATION: –
Ø Sudden Enlargement : From 15 mm to 25 mm Ø Sudden Contraction : From 25 mm to 15 mm Ø Bend : ½ Ø Elbow : ½ Ø Ball Valve : ½ Ø Gate Valve : ½ Ø Water Circulation : FHP Pump, Crompton / Sharp make Ø Flow Measurement : Using Measuring Tank with Piezometer, Capacity 25 Ltrs. Ø Sump Tank : Capacity 50 Ltrs. Ø Stop Watch : Electronic Ø Control Panel : On / Off Switch, Mains Indicator etc. The whole Set-up is well designed and arranged in a good quality painted Structure
Corcyra Egg Laying Cage
Description
Frame made of MDF sheet planks. Fine wire mesh provided on top and bottom fitted with 3mm dia hole wire mesh on one top, a rounded opening 3cm dia is provided which can be closed with wooden plug. On one side a rounded opening 11cm with an arrangement for drop clouser with the help of MDF sheet cover is provided for manually putting in/taking out the material. Size 35x25x18cmXTEMOS ELEMENT
AJAX PRODUCTS TABS WITH ICONS
Plantation Pots
Plantation Pots, moulded in polypropylene, are available in four different sizes.
The Plantation Pots have a downward extended rim, which provide convenient lifting even if the pot is filled.
The bottom of the pot is provided with holes for drain purpose.
Material : Polypropylene
| Particulars | Pack (Pcs) | |
|---|---|---|
| Plantation Pots 100 mm | 20 | |
| Plantation Pots 150 mm | 20 | |
| Plantation Pots 200 mm | 20 | |
| Plantation Pots 250 mm | 20 |
Digital Colorimeter
Description
The basic set-up of the colorimeter is: LED light source: Produces polychromatic light over the entire visible region, 45 Broad spectrum filter: The colorwheel has nine different filters. The filter employed is selected by wavelength. Each filter will produce monochromatic light at a specified peak wavelength with a bandpass of 20 mm. The filters enable the user to perform tests from 400 to 680 nm. Cuvette Holder: It holds the inserted cuvette during testing. It is imperative the cuvette be consistently oriented in the holder. Round cells usually have orientation markings to correctly position the cuvette. Detector: A silicon photo diode is used as the detector. The photo detector current will change as a function of light energy. Display:The current signal from the detector is converted to a numerical value, absorbance and is shown on led display
XTEMOS ELEMENT
AJAX PRODUCTS TABS LOAD MORE PAGINATION
SILICA CRUCIBLE WITHOUT LID
PRODUCT DESCRIPTION
- Crucible is glazed inside and outside.
- Highly resistant to alkalis and hot temperatures
- 50ml capacity
- Outside diameter 55mm, 42mm height
- No lid includedSilica crucible is glazed inside and outside. Highly resistant to alkalis and hot temperature SIZES ARE: 15ML 25ML 50ML 80ML 100ML 150ML
SILICA CRUCIBLE TALL FORM Without Lid, Translucent
XTEMOS ELEMENT
AJAX PRODUCTS TABS CAROUSEL
Laboratory Ice Bucket
We are the Exporters and Traders of Laboratory Ice Bucket.
Our range of Laboratory Ice Bucket is highly appreciated in the market.
This Laboratory Ice Bucket is made of a durable rigid material bearing excellent insulating properties.
Contents can be stored in it using dry ice, liquid nitrogen or acetone etc.
| Particulars | Pack (Pcs) | |
|---|---|---|
| Lee Bucket | 1 |
Rear Suspension System
In this model the working of rear suspension system is shown with the help of actual parts assembled on a metal stand. All the necessary parts of a rear suspension system are shown in actual working form. This model helps the student to understand the working of the rear suspension system very easily. It is specially made dissectible for demonstration purposes.
(A) Leaf Spring Type Suspension System With Rear Rigid Axle
(B) Rear Independent Type Suspension System
Micro Cover Glass
Made from clear optical glass, the cover glasses are uniform in size and free from scratches and striations. Packed in plastic box for easy handling.
Pack of 10 gms
Size
Square Size
18x18mm.
19x19mm.
22x22mm.
Rectangular Size
22x30mm.
22x40mm.
22x50mm.
22x60mm.
24x50mm.
24x60mm.
Circular Size
18mm.
19mm.
22mm.
24mm.
Car Air Conditioning Actual Cut Section
This model will be made out of original parts. The model will be suitably sectioned to demonstrate the internal construction details showing the minute information, and working of the same, the model will be suitably painted and mounted on a metal or wooden base & supplied with key card & very interesting literature regarding working of the same.
