XTEMOS ELEMENT
AJAX PRODUCTS TABS
Brush, Test Tube
Light Dependent Resistor Unit (LDR)
Verification Clarke S Maxwell Reciprocal Theorem
Apparatus for Verification of Clarke’s Maxwell Reciprocal Theorem
Apparatus consist of a mild steel beam 100cm long and 1.25cm x 4mm in cross section with graduations at every 10cm along the length. It should be supported on two knife edge supports 70cm apart with a 30cm overhang on one side. Reciprocal theorem can be verified by direct measurements of the deflections of various points with the help of a dial gauge due to a load placed at the reciprocal points. A dial gauge with 25mm travel (with a magnetic base) should be supplied with the apparatus. Apparatus to be supplied should be complete with a supporting stand and a set of weights.
Experimental Capabilities: To verify Clerk’s Maxwell reciprocal theorem by means of a mild steel be
XTEMOS ELEMENT
AJAX PRODUCTS TABS SIMPLE
Human Skin
T-Joint
XTEMOS ELEMENT
AJAX PRODUCTS TABS ALTERNATIVE
Fashion
SILICA CRUCIBLE TALL FORM Without Lid, Translucent
XTEMOS ELEMENT
AJAX PRODUCTS TABS ARROWS PAGINATION
Discharge Over Notches Apparatus
DESCRIPTION:-
The Lab setup consists of a channel having sufficient length and width in which water is supplied from the bottom. Required Notch is fitted at one end of this channel .A hook gauge with Vernier scale is fitted to measure the height of fluid in flow channel. Arrangement for fixing interchangeable notches is made. Set of three brass notches, i.e. rectangular notch. 60 V notch & 45 V notch provided along with the set up. Present set – up is self –contained water re- circulating unit .provided with a sump tank and a centrifugal pump etc. Flow control valve and by-pass value are fitted in water line to conduct the experiment on different flow rate .Flow rate of water is measured with the help of measuring tank and stopwatch.EXPERIMENTS:-
Ø To Determination Co-efficient of discharge (Cd) through Ø V notch (45 deg. and 60 deg.) Ø Rectangular Notch. Ø Trapezoidal NotchUTILITIES REQUIRED: –
Ø Water Supply & Drain Ø Electricity 0.5kw,220V AC, Single PhaseTECHNICAL SPECIFICATION: –
Ø Channel Test Section : Size 600x250x180 mm Ø Notches : Material Brass(3 Nos) 1. Rectangular Notch 2. 45 deg. V Notch 3. 60 deg. V Notch 4. Trapezoidal Notch Ø Hook / Pointer : With Vernier Scale Ø Water Circulation : FHP Pump, Crompton/Sharp make. Ø Flow Measurement : Using Measuring Tank with Piezometer, Cap.25 Ltrs. Ø Sump Tank : Capacity 70 Liters. Ø Stop Watch : Electronic Ø Control Panel : On/Off Switches, Main Indicator etc. Ø The whole Set-up is well designed and arranged in a good quality painted Structure.
Fuel Supply System Petrol MPFI Type
Fuel Supply System Petrol MPFI Type (Actual Working Model) Multi Point Fuel Injection
This is an actual working model of fuel supply system of a MPFI petrol engine. The parts details is as under :
1. Fuel Tank
2. Fuel Filter
3. Motorised Fuel Pump
4. Pressure Gauge
5. Fuel Rail
6. Fuel Injectors
7. ECU
8. Igniter & Ignition Coil
9. Distributor
10. Spark Plugs
11. Power Supply
12. Fuel Gauge & Control Panel
This model helps the student to understand about the parts & working of MPFI system. It is specially designed for demonstration purposes. The model will be supplied with key card & very interesting literature regarding working.
XTEMOS ELEMENT
AJAX PRODUCTS TABS WITH ICONS
Burner Bunsen LPG
Kidney With Bladder
Mini Rotary Shaker
Body made out of thick mild steel finished with powder coating.
PMDC motor used for shaking.
Platform size 300x300 mm. S.S. platform consists of 9x250ml conical flask lotus type clamps.
RPM range 50-250 RPM, Electronic variable control, with 0-60 min mechanical timer.
Mini Rotary Shaker
Workable on 220 V AC 50Hz single phase.
Optional
Digital R.P.M. indicator Digital timer (0-99 min.)XTEMOS ELEMENT
AJAX PRODUCTS TABS LOAD MORE PAGINATION
SILICA CRUCIBLE WITHOUT LID
PRODUCT DESCRIPTION
- Crucible is glazed inside and outside.
- Highly resistant to alkalis and hot temperatures
- 50ml capacity
- Outside diameter 55mm, 42mm height
- No lid includedSilica crucible is glazed inside and outside. Highly resistant to alkalis and hot temperature SIZES ARE: 15ML 25ML 50ML 80ML 100ML 150ML
SILICA CRUCIBLE TALL FORM Without Lid, Translucent
XTEMOS ELEMENT
AJAX PRODUCTS TABS CAROUSEL
PLC-Logo 6 Pack with Demo Panel Trainer Kit
This Training kit based on Siemens model “Logo” PLC controller, is modulator, versatile, scalable & flexible with integrated Ethernet interface. Many features like High Speed configurable Analog Input etc make it as an Ideal PLC for basic training purpose
PLC Specification
• Make : SIEMENS • Model : CPU LOGORCE • Input Supply : 12/24V DC • Timers &Counters : 256 Nos Each • Digital Inputs : 8 Nos • Digital Outputs : 4 Nos • Program Memory : 400 Blocks • 4 Inputs can be configured as Analog Input (0-10V) DC • Optional SD cards for data logging • Ethernet Communication Interface • Networking with up to 8 unitsDemo Panel Specification
• 8 Nos of toggle switches & LEDs provided for Digital Inputs • 6 Nos of LEDs provided for Digital outputs indication purpose • All I/Os are terminated into SP7 connectors for external trainer interfacing • Patch chords provided for interfacing the external trainers • Modules and all the components mounted on an attractive powder coated metal cabinet • Mimic diagram with screen printing provided in the panel
Three Hinged Arch Apparatus
The mild steel model has a span of 100cm and rise 25cm, with hinges at supports and crown. One of the ends should rests on rollers. Along the horizontal span of the arch various points are marked at equidistant for the application of load. This being a statically determinate structure, the horizontal thrust developed under the action of any load system can be theoretically calculated and will also be measured directly by neutralizing the outward movement of the roller end. A dial gauge with 25mm travel (with magnetic base) may be supplied with the apparatus. Apparatus to be supplied should be complete with a supporting stand and a set of weights.
