XTEMOS ELEMENT
AJAX PRODUCTS TABS
Calorimeter, Electric
Level Control Measurement Module
This module consists of a process tank with a miniature pump, level sensor for 2 levels, a power supply, etc., To establish a ON/OFF control for the level of water. Circuitry is provided for stand alone operation or through a 8255 port of a Microprocessor kit.
Specification
• A transparent tank of height 150mm with adjustable electrodes to vary the high level and low level. • A pump with tank for water circulation • Water level can be monitored under software control/automatic mode • One power relay 230V/6Amp for pump ON/OFF control • Miniature connectors are provided to operate as stand alone controller or through software under a Microprocessor trainer. • Built in power supply.
PAM-PPM-PWM Modulation and Demodulation Trainer
PAM- PPM- PWM is the basic pulse modulation techniques. This trainer provides complete setup to the students for performing Experiments on these techniques. They can study Sampling, Pulse Modulation &Signal reconstruction process. Separate circuits are provided for each Techniques.
FEATURES:
• PAM- PPM- PWM Modulation and Demodulation Techniques,using Natural and Flat - top Sampling. • Natural Sample, Sample and Hold and Flat-top outputs. • Selectable 2 different sampling pulse frequencies on board. • On board Sine wave generators. • Voice communication using dynamic microphone and speaker • On board Filters and Amplifier • Functional blocks indicated on board schematic • Input- Output and Test points provided on board. • Built in DC Power Supply • Fully documented operating ManualTECHNICAL SPECIFICATION:
• Crystal Frequency : 6.14MHz • Sampling Frequency : 16 KHz, 32 KHz • Sine wave Generator : 1 KHz &500Hz, Amplitude (0-5)V, Tolerance +5% • Low Pass Filter : 4 Order BW Filter • Cut off frequency : 3.4 KHz • Voice Communication : Voice Link using dynamic mic& speaker • AC Amplifier : With Adjustable Gain control • Microphone type : Dynamic, 600 Ohm. • Audio Pre-amplifier : Op-amp based • Power amplifier : 1W Mono • Interconnections : BS2 Connector. • Power : 230V, 50HzXTEMOS ELEMENT
AJAX PRODUCTS TABS SIMPLE
Universal Multi Rack
Avail from us high quality Universal Multi Rack at affordable price range.
Souced from reliable vendors, this rack is an excellent lab apparatus compatible with different sizes of tubes.
Four sides of this rack can be used for tubes of 30mm, 20mm, 17mm & 12mm.High grade Polypropylene is used for its manufacturing.
Material : Polypropylene
| Particulars | Pack (Pcs) | |
|---|---|---|
| Universal Multi Rack | 6 | |
| Rotatable Multi Rack | 1 |
Optical Set For Ray Track Apparatus
Description
Comprises a white painted wooden board mounted on nonskid plastic feet, and a removable turntable about 170 mm in diameter. Two orthogonal lines along the turntable’s diameter divide it into four equal quadrants Just beyond the rim of the turntable, a circular scale graduated 90 – 0 – 90 – 0 – 90 °, with 1° subdivision, Also includes a ray box with a 12 V, 24 W bulb Supplied complete with a cylindrical convex lens with focal length approx. 75 mm and two double slits, giving one wide beam slit and one each of single, triple and five slits An optical set is available separately, comprising of one each of rectangular, semi-circular, right-angled triangular – 90 ° 45 ° 45° trapezoidal, biconvex and biconcave prisms.
Microcontroller Based Distance Impedance Relay Trainer
It consists of many components i. Transmission line module ii. Voltage and current signal conditioners iii.Distance Relay iv. Multifunction Meters
Transmission Line Module
• Total line length - 180Km • Modeled by RL - parameters • Current rating - max 5A • Voltage rating - max 250V ACVoltage and Current Signal Conditioners
• One no of 5A/5V current transformer is provided to read the relay current input • One no of 230V/9V potential transformer is provided to read the relay voltage inputDistance Relay
• One PIC microcontroller used as processor to activate the relay function • One LCD to indicate : - Impedance set value - Current & voltage value - Set time, Relay tripping time • Four numbers of keys are used • Parameters - Current input : 0-5Amps, Voltage input : 0-230V AC - Number of contact: One number of NO contact @ 220V, 10Amp rating - Auxillary supply : 230V AC, 50HzMultifunction Meter
• One MFM provided for measuring input side all parameters (V, I, PF, F, AVR, KW) • One MFM provided for measuring load side line parameters
Critical Heat Flux Apparatus
The apparatus demonstrates the regimes of pool boiling. The test section consists of a test wire surrounded by water of constant temperature. The surface temperature of the test wire is heated by passing current through it. Due to the temperature difference between the wire surface and surroundings, the difference regimes are observed till the burnout point.
Specifications:
1.Test wire -35 gauge or 40 gauges. Length = 10cm. 2.Nichrome heater- 1 kw capacity – 1 nos. 3.Glass trough of sufficient capacity. 4.Table light to observe the test wire. 5.Voltmeter and ammeter to measure the input to the test wire. 6.Dimmerstat to adjust the voltage. A technical manual accompanies the unit.SERVICES REQUIRED:
1.220v, ISA, stabilized single-phase supply. 2.Floor surface- 1m x 1m at working height.XTEMOS ELEMENT
AJAX PRODUCTS TABS ALTERNATIVE
Fashion
Rods For Thermal Conductivity Experiments, Copper, Pk of 8 Rods
RNA Model on Stand
Full Functional Elderly Nursing Manikin
Description
Designed according to the demand of the clinical principles and the guidelines of nursing training. This multifunctional simulator could simulate an actual circumstance for practice. Multiple functions, rural practice, easy assembly, well shaped appearance and correct anatomical landmarks provides a very good training for practice.Features:
Head Care Body care Patient moving Different lying pose Bilateral and Unilateral oxygen inhalation Atomization inhalation therapy Nasal Feeding Gastric lavage training Intravenous Injection Intramuscular Injection Hypodermic Injection Various fistula orifice washing practice Female Catheterization Female Bladder Washing Enema Treatment Simulator Assembly
Rotary Pipette Stand
Moulded in Polypropylene, the unique Rotary Pipette Stand holds a maximum of 94 pipettes and rotates on a central vertical axis for convenient selection of any particular pipette.
The lower rotating disc has four concentric troughs with tapered sides and open bottoms that cradle the pipette tips protectively and permit water drops to run off.
The upper disc has a grid pattern concentric with the bottom disc and keeps the pipettes vertical.
Liquids draining off the pipettes are retained on the top of the stationary base by the outer ring.
Our Rotary Pipette Stand can be easily disassembled and reassembled.
| Particulars | Pack (Pcs) | |
|---|---|---|
| Pipette Stand (Rotary) - For 94 pipettes | 1 | |
| Pipette Box | 4 |
XTEMOS ELEMENT
AJAX PRODUCTS TABS ARROWS PAGINATION
Moving Coil Meters
Description
Meters are designed for D.C. measurements to meet every need of schools, colleges and technical institutions. All meters are housed in moulded dust proof cases with zero-adjuster and have connections terminals. Type MO-65 Round.| Case | : | ABS Plastic | |
| Accuracy | : | Class 2.5 | |
| Scale length | : | 50 mm. | |
| Overall size | : | 100x90x90 mm. approx. |
Bending Moment & Shear Force Apparatus
INTRODUCTION:
Shear Forces occurs when two parallel forces act out of alignment with each other. For example, in a large boiler made from sections of sheet metal plate riveted together, there is an equal and opposite force exerted on the rivets, owing to the expansion and contraction of the plates. Bending Moments are rotational forces within the beam that cause bending. At any point within a beam, the Bending Moment is the sum of: each external force multiplied by the distance that is perpendicular to the direction of the force.EXPERIMENT MANUAL:
1. To verify the Shear force a cross-section of the beam. 2. To verify the bending moment in cross–section of beam with a flexure condition.APPARTUS SPECIFICATION:
1. Dimensions : 158 cm X 45cm X (h)60cm 2. Total Beam Length : 160 cm with flexure 3. Width of Beam : 5 cm 4. Distance of Length in between : 5 cm 5. Height of beam : 36 mm 6. No. of Hanger for weights : 3 7. No. of Spring Balance : 2 (of 10kg) 8. Total Weight of Apparatus : 13.1 kgACCESSORY REQUIRES:
1. Shear force apparatus 2. Bending Moment Apparatus 3. Hangers 4. Weights 5. Two Spring balances – 10kgs
Peritoneal Dialysis Simulator
Description
For Continuous Ambulatory Peritoneal Dialysis. Designed to introduce patients, students, and nurses to the essentials of CAPD procedures and care. The realistic torso offers a realistic method to demonstrate and practice peritoneal dialysis. Success with CAPD is dependent on the patient’s following dialysis procedures with extreme care. This Life/form simulator gives the patient an opportunity to gain the confidence necessary for prolonged success with CAPD. Complete with indwelling Tenckh off catheter in a hard carry case. Dialysis materials not included.XTEMOS ELEMENT
AJAX PRODUCTS TABS WITH ICONS
Straight Joint
Siemens IoT 2040 Gateway Based IoT Development System
SIMATIC IoT 2040 is an Industrial IoT Gateway, reliable open platform for collecting, Processing and transmission data. It helps the students to get the industrial IoT experience and develop Industry 4.0 Projects rapidly.
Specification:
• IoT 2040 Gateway - PLC and sensors of many brands can be integrated through Ethernet & Serial ports. - Open Protocols: Modbus, Profinet, REST or MQTT, AMQP, OPC UA - Based on Intel Quark X1020 ,(x86)@400MHz - Compatible With Open Source Software Arduino IDE and Yocto Linux - High level language support : Java, Python, C/C++ - 1 GB RAM, 8MB Flash ,256KB SRAM - Micro SD card Slot up to 32GB - One miniPCIe Slot for hardware expansion for WLAN/Additional Ethernet Port - Arduino Uno – R3 Compatible - Intel Wi-Fi + Bluetooth Module for 300MB data rate - 2xRS232/422/485(Switchable) - 1xUSB Controller + 1 x Device - 2 x 10 /100 Mbps Ethernet RJ45 • 5 types of sensors such as Temperaturesensor, LDR sensor, Motion sensor, Humidity sensor, Magnetic sensor included to • interface with IoT2040 & add on modules of IoT2040 • The IoT 2040 Gateway can communicate with PLC, DCS using profinet or OPC UA. • Analog Inputs are terminated in a SP7 patch connector • 4Nos of Digital Input SPDT Switch • 4Nos of user LEDs
TMS320C6713 Based DSP Trainer
KEY FEATURES:
• Highest performance floating point Digital signal processor (DSP) • 150 MHz Clock rates • 6.7ns Instruction cycle time • 16 bit external memory interface (EMIF) • 16 bit Host-port interface (HPI) • Two multichannel Audio serial ports (MCASPs) • Two multichannel Buffered serial ports (MCBSPs) • Inter integrated circuit (I2C) ModuleONCHIP MEMORY:
• 4KB L1P Program cache memory • 4KB L1D data cache memory • 256KB L2 unifies cache mapped RAMON BOARD FEATURES:
• 512Kx 8bit FLASH for monitor Program • 4M x 16 bit SDRAM for External Memory. • 8 way DIP switches & LEDs to user interface • LCD interface, I2C RTC • Stepper motor Interface • On board USB and UART for serial communication • PCM3002 Audio codecXTEMOS ELEMENT
AJAX PRODUCTS TABS LOAD MORE PAGINATION
SILICA CRUCIBLE WITHOUT LID
PRODUCT DESCRIPTION
- Crucible is glazed inside and outside.
- Highly resistant to alkalis and hot temperatures
- 50ml capacity
- Outside diameter 55mm, 42mm height
- No lid includedSilica crucible is glazed inside and outside. Highly resistant to alkalis and hot temperature SIZES ARE: 15ML 25ML 50ML 80ML 100ML 150ML
SILICA CRUCIBLE TALL FORM Without Lid, Translucent
XTEMOS ELEMENT
AJAX PRODUCTS TABS CAROUSEL
SILICA BASIN (Round Bottom) with spout
PRODUCT DESCRIPTION
Round Bottom Basin With Spout is high purity material that enables products to resist corrosion and withstand the sharp change in temperature. Both of them meet requirements acquired by chemical and physical analysis and have 200ml Capacity.
Available in Different Dimensions:Â
20ml, Dia. 55mm x Ht. 23mm
45ml, Dia. 75mm x Ht. 27mm
70ml, Dia. 87mm x Ht. 33mm
85ml, Dia. 94mm x Ht. 36mm
100ml, Dia. 100mm x Ht. 45mm
200ml, Dia. 113mm x Ht. 47mm
Rotary Shaker (Platform Type)
Body made out of thick mild steel finished with powder coating.
Heavy duty PMDC motors for suitable capacities are provided for long time, continuous operation.
Fixed speed and variable speed models are offered.
Platform is provided RPM range-upto 250 RPM, electronic control, 0-60 min timer.
Workable on 220 V AC 50Hz single phase.
Optional
Digital R.P.M. indicator. Digital timer (0-99 min.).| Platform size in cm | Holding capacity | |
|---|---|---|
| 45x45 mm | 25 flasks of 100 ml | |
| 45x45 mm | 36 flasks of 50 ml | |
| 45x45 mm | 16 flasks of 250 ml | |
| 55x55 mm | 25 flasks of 50 ml | |
| 65x65 mm | 36 flasks of 250 ml | |
| 105x105 mm | 81 flasks of 50 ml | |
| 105x105 mm | 64 flasks of 250 ml |
