XTEMOS ELEMENT
AJAX PRODUCTS TABS
Burner Bunsen – Teclu, LPG
Description
Burner giving a very hot flame, suitable for glasswork and soldering. A needle valve for fine flame adjustment is incorporated die casted base together with a tapered riffled tube connector. A unique spring operated gas safety lock is incorporated of the air/gas mixture. For use on natural gas supplies. Base dia. 80 mm and inlet tube 10 mm dia.Burner Specifications :
Tube Dia. - 13 mm Height - 150 mm Weight - 330 g
Human Eye In Bony Orbit
Car Chassis Rear Wheel Drive Actual Cut Section
Car Chassis Rear Wheel Drive Actual Cut Section – Motorised
4 Stroke 4 Cylinder Petrol Engine With Clutch, Gear Box, Propeller Shaft, & Rear Axle Assembly With Differential Gear
The chassis of the four stroke four cylinder engine cut section model. The cut section model is constructed such that all the following systems can be demonstrated in working conditions.
ENGINE
Maximum parts and accessories of an engine like cylinders, cylinder head, inlet and Exhaust manifolds, FIP, injectors, self-starter, alternator, water pump, radiator, etc., are sectioned to show the internal constructional details. The complete sectioned model is coupled with FHP 220/230V A.C single phase motor through a Reduction drive unit.TRANSMISSION SYSTEM:
This system consists of a Clutch and four speed gearbox assembly, the casing of which is suitably cut to demonstrate its operation. The gearbox is coupled to Differential gear box with propeller shaft and the different coupling used for this transmission can be demonstrated. The Differential gear box is also cut so as to clearly to demonstrate its complete operating principle. The gear shifting including the forward and reverse gear operation can be clearly shown. The speed variation and the rotation of the Differential gear box can be seen while gear shifting. By running the motor connected to the engine assembly the entire system with gear box, rear axle etc. can be demonstrated in running. FUEL SYSTEM: The Fuel tank is cut to expose the mounting of the level sensor and the position of Fuel section. The system is complete with mechanical Fuel pump. EXHAUST SYSTEM:It consists of Exhaust Manifold and silencer in cut section to explain internal construction. LUBRICATION SYSTEM: It consists of the engine Lubrication system along with the Lubrication oil pump is suitably sectioned. SUSPENSION SYSTEM: This will explain both the Hydraulic Suspension systems at the front and the leaf spring Suspension at the Rear. One of the hydraulic arrangements of Suspension mechanism is highlighted (with shock absorbers) and explained cut sectionally.BRAKING SYSTEM:
The Hydraulic or Air circuit Brakes. The movement of the Brake Shoes on operating the brake pedals can be seen in the area where the Brake drum is cut. The front and rear brakes will be operational. STEERING MECHANISM: The can be seen and included in the Steering wheel. Steering gear box and coupling of the same to the wheels will be shown by rotating the steering wheel, the operation of the steering system can be demonstrated. The entire system will be mounted on the chassis, and suitable mounting option with caster wheels will be provided for easy movability.XTEMOS ELEMENT
AJAX PRODUCTS TABS SIMPLE
Pipette Stand, Wooden – Horizontal
Transfer Case Assembly Actual Cut Section
Transfer Case Assembly – Actual Cut Section
The working of transfer case is shown with the help of actual parts assembled on square iron pipe frame. All the necessary parts of transfer case are shown in actual working form. This model helps the student to understand the working of the transfer case very easily. It is specially made dissectible for demonstration purposes.
Wankel Engine Model
The model demonstrates the principle, operation. It is cutaway to show the internal constructional details. Unlike other engines the rotary piston engine avoids reciprocating parts. The power pistons an arch like triangular rotor which on rotating generates an epitrochoid. Mounted on metal base with printed diagrams.
XTEMOS ELEMENT
AJAX PRODUCTS TABS ALTERNATIVE
Fashion
Microtome
Sonometer, Simple
XTEMOS ELEMENT
AJAX PRODUCTS TABS ARROWS PAGINATION
Falling Body Apparatus
L-Section launcher with holes for locating two 19mm.
diameter steel balls which act as projectiles.
Launcher is released by push button and projects one ball forward while allowing the other to fall freely Launching mechanism mounted on wooden block, 180x60x30mm.
which may be clamped by bench and has a convenient storage pocket for the balls.
Complete with two steel balls.
Resistance Units
Xilinx Spartan 3E FPGA Trainer Kit
Specification
• XC3S250E - 4PQ208C / XC3S500E-4PQ208C • 16 Nos. of digital input using slide switches with LED indication • 16Nos. Of digital outputs using discrete LEDs • 16 x 2 LCD is provided for display the text message. • One Reset Switch • One switch is provided for giving manual clock • FPGA configuration through - JTAG Port - On board Flash Prom XCF02S • Total 158 I/O pins : 124 pins used for integrating peripherals like LED, Switches etc., balance pins available to user in 20 pin • header (3.3V compatible) • 1No of 26pin header to interface VLIM cards like Traffic Light Controller (5V compatible) • On board programmable PLL oscillator from 1 MHz to 100 MHz using jumpers • 4 Nos of 7 segment LED display • One relay and Buzzer provided. • Stepper & DC motor Driver provided. • 4 * 4 matrix key provided • Housed in a sleek plastic cabinet with built in SMPS 5V/2A. • Compatible with Xilinx ISE Design Suite WebPACK Software. • On board USB to JTAG is available for configure FPGA (Supports only with Vi JTAG 5.0 Software)
XTEMOS ELEMENT
AJAX PRODUCTS TABS WITH ICONS
Composite Walls Apparatus
Composite Walls Apparatus:
The apparatus consists of a pair of M.S. plates, Bakelite, brass/aluminum. These plates in series on either side of the heater form a composite wall. The whole unit is clamped in a frame, which can be viewed through the Perspex sheet. The thermocouple tapings enables us to find out the conductivity and resistance of the composite walls.
SPECIFICATIONS:
1.Heater- Mica healer of dia. 250 mm. 2.Plates- a) M.S. plates of thickness 25mm & dia. 250mm.-2 nos. b) Bakelite plates of thickness 10mm & dia. 250mm.-2 nos. c)Brass/Aluminum plates of thickness 15mm & dia. 250mm.-2nos 3.Dimmerstat – 2 A capacity. 4.Measurements — a) voltmeter and an Ammeter to measure input power. b) Multichannel digital temperature indicator to measure temperatures at- various points. A technical manual accompanies the unit.SERVICES REQUIRED:
230 V, A.C. stabilized supply along with earthing connection. Bench area Im x lm x 0.5m height
Model of Terrestrial Telescope
XTEMOS ELEMENT
AJAX PRODUCTS TABS LOAD MORE PAGINATION
SILICA CRUCIBLE WITHOUT LID
PRODUCT DESCRIPTION
- Crucible is glazed inside and outside.
- Highly resistant to alkalis and hot temperatures
- 50ml capacity
- Outside diameter 55mm, 42mm height
- No lid includedSilica crucible is glazed inside and outside. Highly resistant to alkalis and hot temperature SIZES ARE: 15ML 25ML 50ML 80ML 100ML 150ML
SILICA CRUCIBLE TALL FORM Without Lid, Translucent
XTEMOS ELEMENT
AJAX PRODUCTS TABS CAROUSEL
Redundant Joint Apparatus
Apparatus consists of three suspension members (spring balances) of different stiffness, which are jointed at a point to form the redundant joint. The upper end of the suspension members being tied in a position to a vertical wooden board. Arrangement is provided to apply a vertical load at the joint and to measure its horizontal and vertical displacement on a paper and also elongations and forces in the suspension members by the help of dial gauges. Dial gauges with magnetic base are provided with the apparatus.
