XTEMOS ELEMENT
AJAX PRODUCTS TABS
Specimen Jar
We have come up with a quality range of Specimen Jars.
These transparent Specimen Jars are used for preserving different specimens in the lab and are provided with a cap that fits in tight.
These jars provided excellent protection to the species preserved in it.
Material : Polystyrene
| Particulars | Pack (Pcs) | |
|---|---|---|
| Specimen Jar (Gas Jar) | 12 |
Charle’s Law Apparatus
Description
To determine co-efficient of expansion of a gas at constant pressure. A glass U-tube with a bulb and stopcock at one end, the other limb being open. An outlet tube from the bottom of the U tube passes through a rubber bung and has a stopcock at the end. The stem below the bulb is graduated 3 x 0.1 ml. An inlet tube with a mohr clip also passes through the bung. A glass water jacket encloses the U tube. All glass parts made of borosilicate glass requires only 20 ml mercury, which is not included.
XTEMOS ELEMENT
AJAX PRODUCTS TABS SIMPLE
Spring Unit of Mechanical Model
Description
For showing potential energy in a wound-up spring and its conversion to electrical energy by driving a dynamo and lighting a lamp. May also be used to wind up a weight on a cord showing the change from potential energy to kinetic and back to potential in the raised weight. The steel shaft carries a clock spring with a free wheel device and winding ratchet, also an aluminium 'V' pulley 56 mm. diameter. One end of the shaft overhangs the base for use as line shaft when winding up a weight. Dimensions 220 x 100 x 100 mm. high Supplied complete with driving belt.
Polarimeter
Description
Suitable for determining specific rotation of optically active substances. It has Laurent’s quartz half shade device which make the system sufficiently accurate and at the same time simple, suitable for use with sodium light. The circular head is attached to the analyzer. Vernier movable over the scale enables reading 0-360° or 0-180°. A 200 mm tube is provided with the instrument. Mounted on a sturdy tripod stand.
Suspension Bridge Apparatus
DESCRIPTION:
Cables are frequently used to support loads over large spans such as cable stayed for suspension bridges, cable car systems and stadium roof. They are used extensively for permanent guys on structures such as microwave towers and derricks. They are also used for temporary guys during erection. The only force in a cable is direct tension. They are too flexible to carry any moment. A cable is used to carry concentrated loads, uniformly distributed load along its length and uniformly distributed load along the horizontal span. It takes the shape of a polygon under concentrated loads, a catenary under uniform load along its length (such as its own weight), and a parabola under uniform load along the horizontal span.EXPERIMENT:
• Study the Extension of each spring Balance Left & Right Both. • Study of the effect of a point loadTECHNICAL SPECIFICATION:
• Apparatus Consists of two mild steel cables 0.5cm diameter in cross section and 150cm long, pinned to two supports 90cm apart situated symmetrically. • One of the ends can be converted to a roller by applying a known load at the end with the help of suspended pulley system. • Vertical loads can be applied at various points along the span of the beam. • A dial gauge with 25mm travel (with a magnetic base) is to be supplied with the apparatus complete with a supporting stand and a set of weights.
Heat Pipe Apparatus
Heat Pipe Apparatus:
Heat pipe is an interesting device, which is used to transfer heat from one location to another.
The apparatus consists of three pipes, viz. A heat pipe, copper pipe and stainless steel pipe. Ail the pipes have same physical dimensions. Copper and stainless steel pipes serve the purpose of comparison of heat pipe performance. All pipes are mounted vertically with a band heater at lower end and water filled heat sink at upper end. Nearly isothermal operation of heat pipe is clearly visualized from longitudinal temperature distribution of the pipe.
SPECIFICATIONS:
1.Heat pipe – Stainless Steel pipe, 25 mm O.D., 450 mm. Long. Sealed at both ends, evacuated and filled partially with distilled water – one No. 2.Copper and stainless steel pipe of same size as that of heat pipe – one each. 3.Equal capacity heater at bottom end of each pipe. 4.Water filled heat sinks at upper end of each pipe.Measurements and controls
a) Dimmerstat to control heat input to all the heaters – 4 amp. Capacity One No. b) A voltmeter and an ammeter to measure input to heaters One each. c) Multichannel digital temperature indictor to measure temperatures along the length of pipes.Four thermocouples are provided on each pipe. v Thermometers to note down water temperatures in heat sinks – 3 Nos.Services Required:
230 VA.C. Single Phase supply. Floor Area = 1 m X 0.5m X 0.5 m height.XTEMOS ELEMENT
AJAX PRODUCTS TABS ALTERNATIVE
Fashion
Ripple Tank
Description :-
Transparent acrylic plastic ripple tank, supported in a sturdy plastic frame which has recesses to hold four legs with leveling feet.
The tank edges are shaped to minimize undesired reflections.
Tank has a drain hole closed by a rubber stopper.
With two light alloy uprights to carry a horizontal rippler support rod which is adjustable for height.
The ripple assembly, elastically suspended from the support rod, consists of a 4 – 6 V DC motor mounted on a wooden beam.
The motor has an eccentric weight which causes the beam to oscillate.
Two point sources are provided by two plastic spheres, each mounted on a right angle rod.
A metal rod is fixed centrally into a socket in one short side of the frame to afford support to the illuminant.
Overall size of the tank 580 x 500 x 80 mm, window area 370 x 280 mm, height of tank above bench level (with legs attached) approx. 375 mm.
Complete with following accessories :-
1. Two straight obstacles of aluminium alloy length 130 mm.
2. One straight obstacle length 40 mm.
3. One curved reflector radius 200 mm.
4. One trapezoidal plastic plate for refraction.
5. One wood hand wave roller.
6. One water dropper.
7. One pkt. rubber bands.
8. One foam plastic sponge.
9.One illuminant with a 12 V, 24 W lamp mounted in a lamp house and provided with a long supporting rod.
Domestic Refrigerator Actual Cut Section
This model will be made out of original parts. The model will be suitably sectioned to demonstrate the internal construction details showing the minute information, and working of the same, the model will be suitably painted and mounted on a metal or wooden base & supplied with key card & very interesting literature regarding working of the same.
XTEMOS ELEMENT
AJAX PRODUCTS TABS ARROWS PAGINATION
Plastic Storage Box
We export and trade high quality Plastic Storage Boxes.
These Storage Boxes, made of polypropylene, prove to be an excellent option for storage of different powdered reagents & other material in the laboratory.
Square shape of these boxes helps in saving shelf space.
Available in three different sizes these boxes have polypropylene caps, are autoclavable, provide good chemical resistance & heavy duty service.
| Particulars | Pack (Pcs) | |
|---|---|---|
| Storage Box 250 ml | 12 | |
| Storage Box 500 ml | 12 | |
| Storage Box 1000 ml | 12 |
Human Torso, With Head, Half Size
Histology Set II
Set of 24 slides consisting of
| Adrenal gland | Areolar tissue |
| Cereburm | Colon |
| Compact bone, LS | Heart, entire LS |
| Human plantar skin | Hyaline cartilage |
| Kidney, LS | Liver, injected |
| Lung, LS triple stain | Lymph node |
| Olfactory epithelium | Oviduct |
| Penis | Peripheral nerve |
| Pituitary, V.LS | Sperm Smear |
| Striated muscle, TS | Thyroid gland |
| Tooth | Trachea |
| Ureterv | White Fibre-Cartilage |
XTEMOS ELEMENT
AJAX PRODUCTS TABS WITH ICONS
Frequency Modulation And Demodulation
This Instrument is design to demonstrate the method to transmit signals via. Electromagnetic transmission and to study the Frequency Modulation and Demodulation. Whole instrument is placed in plastic moulded box and 2 mm banana plug leads are provided for modulation and demodulation connections.
Technical Specification:-
1. Fixed Output DC Regulated Power Supply of ±12 V.
2. Built in Modulating signal Generator of 2 KHz and 4 KHz selectable with a toggle switch with Amplitude to 3V peak to peak approximately.
3. Circuit diagrams for Modulator and Demodulator are printed on the milky white top panel
Rear Axial Assembly With Differential Gear
Rear Axial Assembly With Differential Gear Fully Floating Type – Actual Cut Section
The working of differential gear is shown with the help of actual parts assembled on square iron pipe frame. All the necessary parts of differential gear are shown in actual working form. This model helps the student to understand the working of the differential gear very easily. It is specially made dissectible for demonstration purposes.
Photo Gates & Leads
These pair of photo gates is housed in tough moulded cases giving them excellent durability.
The lamps operate on 6 Volts with a special built in circuitry which prevents lamps from damage in case higher voltage is applied accidently.
The photo gates can be connected by 4 mm. sockets to a timer and power supplies.
XTEMOS ELEMENT
AJAX PRODUCTS TABS LOAD MORE PAGINATION
SILICA CRUCIBLE WITHOUT LID
PRODUCT DESCRIPTION
- Crucible is glazed inside and outside.
- Highly resistant to alkalis and hot temperatures
- 50ml capacity
- Outside diameter 55mm, 42mm height
- No lid includedSilica crucible is glazed inside and outside. Highly resistant to alkalis and hot temperature SIZES ARE: 15ML 25ML 50ML 80ML 100ML 150ML
SILICA CRUCIBLE TALL FORM Without Lid, Translucent
XTEMOS ELEMENT
AJAX PRODUCTS TABS CAROUSEL
Ray Optics Kit
Description
Consists of 2 lamps and two stands, 1 pair housing shields, 2 combined single and triple slit plates, 2 multiple slit combs, 2 holders for combs and slit plates, 4 wooden light barriers, and following cylindrical lenses, of size 50 x 50 mm. 4 No Lenses of +7D, 2 of +10D, 2 of +17D and 2 of -17D.
Microprocessor Photo Colorimeter
Microprocessor Photo Colorimeter is a compact and easy to operate instrument for Photo Colorimeter analysis of any concentration.
The output is available on a 16 x 2 line alphanumeric backlit LCD display in terms of %Transmission (%T), Absorbance (Abs.), Concentration (Conc.) and K Factor.
This instrument has 100 sample storage memory and printer output facility for printing data with any dot matrix printer.
The use of microcontroller has made it extremely versatile and accurate instrument.
10 mm path length matched test tubes are used for sample and blank.
The use of high class standard wide range glass filters covering 400 to 700 nm give extremely good results.
The filter setting is controlled by a rotating disc having 8 filters.
An automatic shutter is provided to stop the light reaching the photocell, when test tube is not inserted in the tube holder.
This increases the life of photocell tremendously.
Facility has been provided to store the last K Factor and the standard concentration value.
User can also enter any known ‘Factor’ for a test, thereby eliminating the need to re-run the standards again and again.
Specifications
| Wavelength Range | 400 - 700 nm | |
| Resolution | %T: 1, Abs: 0.01, Conc.: 0.01, K Factor: 0.01 | |
| Photometric Range | %T: 0 - 100, Abs: 0 - 1.99, Conc.: 0 - 1999, K Factor: 0 - 1999 | |
| Detector | Wide range Silicon Photodiode/Photocell | |
| Display | 16 x 2 line alphanumeric backlit LCD display | |
| Keyboard | Soft Touch Membrane Keys | |
| Data Storage | Up-to 100 Samples (0 - 99) | |
| Light Sources | 6.8 V, 0.3 Amp Tungsten Lamp | |
| Sample System | 10 mm path length matched glass test tube | |
| Filters | 400, 450, 490, 520, 540, 570, 620, 680 nm | |
| Printer Interface | Centronics Parallel Printer interface for Dot Matrix Printer | |
| Serial Interface | RS-232C interface (optional available on request) | |
| Power | 230 V ± 10% AC, 50 Hz | |
| Dimensions | (L x B x H) 240 x 254 x 90 mm (Approx.) | |
| Weight | 2.5 Kg (Approx.) |
Accessories
Matched Test Tube: A set of 5, Spare Lamp, Mains Lead, Operation Manual and Dust Cover.
Refrigeration Trainer Domestic Type
The unit enables students to study the various parameters affecting the performance of a domestic refrigerator. It consists of refrigeration cycle of domestic refrigerator, it consists a hermetically sealed compressor, air-cooled condenser, capillary tube and a natural convection type evaporator. The evaporator is fitted with a small heater to simulate different load conditions various measurements are provided so that power consumption, COP, theoretical and actual refrigerating effects refrigerant flow rate and effect of door opening on power consumption can be studied and also students can visualize automatic operation of unit using a thermostat.
SPECIFICATIONS:
1.Compressor – Hermetically sealed, Kirioskar make having capacity of approx. 1/25 ton of refrigeration. 2.Air – cooled condenser with natural convection airflow. 3.Capillary tube of matched length as expansion device. 4.Evaporator coil with an electric heater inside and adequate glass wool insulation on all side. 5.Measurement a)Energymeter Tore compressor input power measurement. b)Pressure gauge for condensing and evaporating pressure. c)Flow meter for liquid refrigerant flow d)Digital Temperature indicator for measurement of temperature 6.safety & Controls a)High & low pressure cutout. b)Thermostat. c)Necessary Switches. A technical manual accompanies the unit. Also, the unit is provided with an attractive and rust proof powder coating.SERVICES REQUIRED:
1.Floor space of 2m x 1m. 2.230V AC stabilized supply with earthing connection
Hydraulic Linear Actuation System Trainer with Labview Interfacing
Features
• This trainer helps to learn the characteristics of double acting cylinder namely direction, speed & force. • A Microcontroller ADC relay driver provided to actuate the cylinder. • Gear pump supplies the hydraulic fluid to double acting cylinder through direction control valve. • Pressure control valve controls the flow rate of fluid to cylinder. • Single phase induction motor drives the pump. • Control unit communicate with PC and controls the double acting cylinder using LabVIEWSoftwares. • Two proximity sensors are provided to indicate the position of the cylinder. • Load cell measures the force developed by the cylinder. • 5/2 Double Solenoid Valve directs the cylinder. • One tank is used to store the hydraulic fluid.
