XTEMOS ELEMENT
AJAX PRODUCTS TABS
Anaerobic Culture Jar
Description
Transparent Anaerobic Culture Jar of 3.5.lit. capacity which is made of Polycarbonate. The lid of the jar is made of Aluminum pressure die Casting fitted with Pressure Valve, Vacuum Valve, Safety Valve & compound Pressure cum vacuum gauge, three finger aluminum clamp and sealing "O" ring. This is recommended only where inside air of jar is removed thru vacuum pump and CO2 is filled in the jar thru CO2 gas cylinder to generate anaerobic condition in the jar. Also supplied with plain aluminum pressure die casted lid which can be fitted when readymade gas packs are used to generate the anaerobic conditions inside the jar. When readymade gas packs are used, there is no need of lid fitted with dial gauge etc., for extra life of equipment.
Refrigeration Trainer Domestic Type
The unit enables students to study the various parameters affecting the performance of a domestic refrigerator. It consists of refrigeration cycle of domestic refrigerator, it consists a hermetically sealed compressor, air-cooled condenser, capillary tube and a natural convection type evaporator. The evaporator is fitted with a small heater to simulate different load conditions various measurements are provided so that power consumption, COP, theoretical and actual refrigerating effects refrigerant flow rate and effect of door opening on power consumption can be studied and also students can visualize automatic operation of unit using a thermostat.
SPECIFICATIONS:
1.Compressor – Hermetically sealed, Kirioskar make having capacity of approx. 1/25 ton of refrigeration. 2.Air – cooled condenser with natural convection airflow. 3.Capillary tube of matched length as expansion device. 4.Evaporator coil with an electric heater inside and adequate glass wool insulation on all side. 5.Measurement a)Energymeter Tore compressor input power measurement. b)Pressure gauge for condensing and evaporating pressure. c)Flow meter for liquid refrigerant flow d)Digital Temperature indicator for measurement of temperature 6.safety & Controls a)High & low pressure cutout. b)Thermostat. c)Necessary Switches. A technical manual accompanies the unit. Also, the unit is provided with an attractive and rust proof powder coating.SERVICES REQUIRED:
1.Floor space of 2m x 1m. 2.230V AC stabilized supply with earthing connection
U Shaped Magnet
XTEMOS ELEMENT
AJAX PRODUCTS TABS SIMPLE
Lymphatic System
Set of Springs
Seeds & Fruits
Description
All Charts are made on PVC rexine, hand drawn, waterproof, in fast multi colors with a black background. Each chart is provided with rollers to hang on wall. Size 75×100 cm. Maize seed germination Gram seed germination Bean seed germination Castor seed germination Pea seed germination Dispersal of seeds & fruits Classification of fruits
XTEMOS ELEMENT
AJAX PRODUCTS TABS ALTERNATIVE
Fashion
Biological Science Set
Set of 22 slides. Fulfils the requirements of most biology courses.
The slides have been chosen for their relevance to international Curriculum and for the clarity with which they show structures, which may be related directly to function.
The set comprises following slides.
| Adipose tissue | Allium LS root tip for mitosis |
| Allium, Leaf, WM epidermis with stomata | Artery and vein |
| Cucurbita, stem, TS and LS | Entire Kidney, LS Mixed Bacteria |
| Germinating pollen, LS stigma | Human blood smear |
| Ligustrum (Privet) TS leaf | Lung |
| Mixed Pollen | Nerve cells, isolated |
| Nettle stinging cells | Pacinian corpuscle receptor cells |
| Saccharo0myces, budding | Skin |
| Small intestine, TS injected | Squamous, epithelium, cheek cells |
| Stomach, VS | Straited muscle |
| Triticum, LS Seed | Zea Stem, TS and LS |
Light Dependent Resistor Unit (LDR)
Comparative Study
Description
All Charts are made on PVC rexine, hand drawn, waterproof, in fast multi colors with a black background. Each chart is provided with rollers to hang on wall. Size 75×100 cm. Vertebrate Hearts Vertebrate Brains Vertebrate Skulls Vertebrate Limbs Vertebrate Girdles Vertebrate Urino genital system Vertebrate Embryos Vertebrate Arterial arches circulation Vertebrate Genital apparatus & venous systemXTEMOS ELEMENT
AJAX PRODUCTS TABS ARROWS PAGINATION
Electronic Digital Theodolite
Description
This cost-effective Electronic Digital Theodolite provides excellent performance, reliable quality and practical operation for any construction application. The body style is similar to a Topcon Digital Theodolite and is combined with easy to use operation. The smart appearance and reasonable structure is as attractive as its price. • Tribrach. • AA Rechargeable Batteries (4 each). • Lens Cap. • Operator's Manual. • Hard carrying case.
Brown Plant Hopper Insect Rearing Cage
Description
Framework of seasoned teakwood, nicely polished. Front door and top provided with non rattling glass and back & two sides with nylon wire screen supported by fine wire mesh. Wooden base covered with laminated sheet from inside. Size: 45x45x55 cm. Brown Plant Hopper Insect Rearing Cage Size: 60x60x80 cm.XTEMOS ELEMENT
AJAX PRODUCTS TABS WITH ICONS
CAVITY BLOCK
Reptilia Histology
Educational Equipments Manufacturer, Exporters & Suppliers - School Educational Equipments Manufacturers & Exporters of Educational Equipments for Lab.
Science Lab Products, Teaching Aids, Classroom Instruments, Educational Laboratory
Skin VS
Tongue TS
Oesophagus TS
Duodenum TS
Intestine TS
Rectum TS
Liver TS
Pancreas TS
Trachea TS Lung TS
Kidney TS
Ovary TS
Testis TS
Spinal Cord TS
Brain LS
Brain TS different Regions
Organ of Jacobson's TS
Digital Bomb Calorimeter
DIGITAL BOMB CALORIMETER
Bomb Calorimeter outfit provides a simple and inexpensive method for determination of heat of combustion of organic matter and the calorific value and sulphur content of solid and liquid fuel. The outfit supplied is complete for analysis as per the method recommended by British Standard Institution BS 1016. All parts of the outfit have been finished of petroleum and British Standard Institute.SUPPLIED WITH
Calorimeter Vessel with bomb support, Water jacket, Combined Lid for calorimeter vessel and water jacket, Stirrer, Connecting Leads, Connecting tube to connect bomb & pressure gauge, Connecting tube with fine adjustment valve, to connect pressure gauge, pressure gauge on stand, Spanner for oxygen tube connection, Ignition Wire, (2 meters) Nichrome, Cotton Real, stand for bomb lid, Hook for lifting bomb, stainless steel Crucible, Gelatine capsules, Gas release valve, Bomb firing unit, Vibrator, Timer, Benzonic acids. ‘O’ Ring Big, ‘O’ Ring Small, ‘O’ Ring for Stirrer Valve for Bomb, Valve Kay. Complete with Instruction manual.XTEMOS ELEMENT
AJAX PRODUCTS TABS LOAD MORE PAGINATION
SILICA CRUCIBLE WITHOUT LID
PRODUCT DESCRIPTION
- Crucible is glazed inside and outside.
- Highly resistant to alkalis and hot temperatures
- 50ml capacity
- Outside diameter 55mm, 42mm height
- No lid includedSilica crucible is glazed inside and outside. Highly resistant to alkalis and hot temperature SIZES ARE: 15ML 25ML 50ML 80ML 100ML 150ML
SILICA CRUCIBLE TALL FORM Without Lid, Translucent
XTEMOS ELEMENT
AJAX PRODUCTS TABS CAROUSEL
Transducer Trainer
Specification
• RTD acts as a temperature sensor • Strain gauge based load cell • Linear variable resistive transducer • LDR, Photo diode, photo transistor • Precision servo potentiometer • Inductive type proximity sensor • Heat source, Filament lamp, Buzzer • 3½ digit LED display • Analog type 10V Center-Zero meter • Inverting and Non-inverting amplifier • Amplifier with Gain and offset control • Instrumentation and summing amplifier • Low pass filter • Precision Rectifier • Timer and buzzer oscillator • Electric switch
Transmission Line Trainer
This trainer is designed for study of co-oxial cable characteristics like Impedance measurement, VSWR measurement etc., It is based, i) The latest technology of DDS Based RF source. ii) Directional coupler for VSWR Measurement. iii) TDR to measure the cable fault.
Specification
• DDS RF Source - Frequency: 10 to 400MHz. - Step Size: 1KHz. - Direct Digital Synthesis (DDS) Method Based. - Since DDS Device is primarily digital, it offers. • Display: Graphics LCD display of 240x128 pixels with backlight to plot VSWR, TDR characteristics etc., • One directional coupler provided for VSWR, Return loss measurement. • In-Built RF Detector for 10-400MHz Frequency range. • In-Built TDR (Time Domain Reflectometer) to measure and study nature of discontinuation in the co-axial cable. • Output Impedance: 50 ohms. • Co-axial cable: Various lengths of 50 ohm, 75 ohm cables supplied. • All relevant waveforms are displayed graphically in the Graphics LCD
Pelton Wheel Turbine Test Setup
DESCRIPTION:
Pelton Wheel Turbine is only impulse water turbine now in common use named in honor of Sir L.A. Pelton (1829-1908) of California, USA. It is a tangential flow impulse turbine. The water strikes the buckets along the tangent of the runner. The energy available at the Inlet of the Turbine is only kinetic energy. The Pressure at the Inlet and Outlet of the atmospheric. This turbine is used for high heads. The Present Set-up consists of a runner. The buckets are mounted on the runner. The water is fed to the turbine, through SS nozzle with a SS spear, by means of Centrifugal Pump, tangentially to the runner. Row of water into turbine is regulated by adjusting the spear position by the help of a given hand wheel the runner is directly mounted on one end of a central SS shaft and other end is connected to a brake arrangement. The circular window of the turbine casing is providing with a transparent acrylic sheet for observation of flow on to the buckets. This runner assembly is supported by rigid MS structure. Load is applied to the turbine with the help of this brake dynamometer so that the efficiency of the turbine can be calculated. Pressure Gauge is fitted at the Inlet of the turbine to measure the total supply head to the turbine.EXPERIMENT:
1.To study the operation of a Pelton Wheel Turbine 2.To determine the Output Power of Pelton Wheel Turbine 3.To determine the Turbine EfficiencyUTILITIES REQUIRED:
● Water Supply and Drain.● Electricity 15 kW, 440V AC, Three Phase
TECHNICAL SPECIFICATIONS:
| MODEL | HM 111 (1.33 HP) | HM 111 (2 HP) | HM 111 (5 HP) |
| Output Power | 1.33 HP / 1 Kw | 2 HP / 1.5 Kw | 5 HP / 3.75 Kw |
| Discharge | 300 LPM (Approx.) | 400 LPM (Approx.) | 630 LPM (Approx.) |
| Supply Head | 25 m | 40 m | 45 m |
| Rope Brake Dynamometer | Dia 200 mm | Dia 200 mm | Dia 300 mm |
| Sump Tank | Capacity 150 Liters. | Capacity 200 Liters. | Capacity 300 Liters. |
| Water Circulation Centrifugal Pump | Capacity 5 HP, Three Phase | Capacity 7.5 HP, Three Phase | Capacity 15 HP, Three Phase |
| Speed | 1000 RPM (approx.) | ||
| Impeller | Material Brass, Bucket type | ||
| Nozzle | Material Stainless Steel/Mild Steel | ||
| Spear | Material Stainless Steel/Mild Steel | ||
| Discharge Measurement | Pitot Tube with Manometer | ||
| Control Panel | Star/Delta Starter, Mains Indicator, MCB for overload protection | ||
| The whole set-up is well designed and arranged in a good quality painted structure. | |||
IPM Based Power Module
Power Module is designed for Motor control Applications upto 3 HP by using IGBT & DIODE Technology Based IPM. Input:1 Phase / 3 phase 50 Hz AC. Output : 400V/10A (MAX), AC/DC on each Leg of 3 phase Bridge
FEATURES:
• 1200V, 25A, 3 Phase IGBT Inverter Bridge • 1200V, 10A IGBT for Over Voltage breaking • Built - in Over Voltage, Under Voltage, Over Current & Over Temperature ProtectionADDITIONAL FEATURES:
• 1200V, 25A Converter Bridge for AC-DC power conversion • 4 Nos of Hall Effect current sensors are provided to sense the DC Link current & 3 output current of the Inverter Bridge • 1 No of Hall Effect Voltage sensor is provided to sense DC Link voltage • All the PWM signals are isolated using Opto Isolator • Protection circuit for over current with LED indication • Optically Isolated Fault signal from the IPM is given to the Embedded/DSP controllers for protection. • Independent Power supplies for all Isolated circuits. • 0-900V Voltmeter is provided to Indicate the DC Link Voltage • All current, PWMS & Feedbacks are terminated at Front panel • FRC Connectors are provided to Interface with the Embedded/DSP controllers • All the Input/output Lines are terminated at Banana sockets.
Carboys
Carboys, made of polypropylene, are much lighter than glass.
These autoclavable, dependable & durable Carboys are provided with wide handles making it convenient while carrying or pouring purposes.
We also offer carboy with stopcock for the esteemed clients.
Material : Polypropylene
| Particulars | Pack (Pcs) | |
|---|---|---|
| Carboy 10 ltrs. | 1 | |
| Carboy 20 ltrs. | 1 | |
| Carboy With Stop Cock 10 ltrs. | 1 | |
| Carboy With Stop Cock 20 ltrs. | 1 |
Microcontroller Based Differential Relay
This test set-up consists of a. Microcontroller based differential relay. b. 300VA transformer set-up
Specification
• One PIC Microcontroller used as processor to read all current, (PY, SY) & activation of relay function • One LCD to indicate, - Set value, All currents - Set time, DMT/IDMT type - Relay tripping time. - Biased/Unbiased type status • Four numbers of key used - To select IDMT/DMT type or biased un-biased type - Set current value adjustment - Set time adjustment - Reset function • Six 5A CT used to sense primary and secondary current. • One 12V TPTT auxiliary relay used for contactor operation. • Specification: - Current input : 0-5Amp - Voltage input : 0-230V - Number of contact : Three number No contact @ 220V, 10Amp rating. - Auxiliary supply : 230VAC, 50Hz • PC interfacing facility power ON/OFF switch with indicator. • Make : VI MICRO • Model : VPL - 83A
CONDENSER CLAMP
PRODUCT DESCRIPTION
- Three finger condenser extension clamp with Bose head.
- Aluminum stem the overall length of the clamp is 10.0.
- The extension rod contributing 6 the rubber coated jaws will open to 3.5 and will provide a six point contact for a firm
- The boss head right angle clamp will accept rods up to.63 /16 mm.
- 3 Finger Aluminium Condenser Clamp (Rubber Lined)
- 4 Finger Aluminium Condenser Clamp (Cork Lined)
- 3 Finger Brass C.P. Condenser Clamp (Cork Lined)
- 4 Finger Brass C.P. Condenser Clamp (Cork Lined)
