XTEMOS ELEMENT
AJAX PRODUCTS TABS
Wave Machine, Powell’s
Discrete Component Trainer
Trainer consisting of Power Supply of +5 V / ±12 V (each of 250 mA), Silicon, Germanium diodes, Zeners, PNP and NPN Transistors, FET, One speaker, 12 different values of carbon film resistances of ¼ W, ½ W and 1 W. 12 assorted values of capacitors from 100 pF to 1000 ?F, Integrated Circuit (IC) Base and IC 74LS00 1 No. each. LED, LDR, Photo diode, Solar Cell Logic Switches (4 No.) and LED Indicators (4 No.) etc., 2 mm Interconnection Leads -10 No. and Comprehensive User’s Manual
Triangle Kit
HISTOLOGY
These three sets build up to a complete study of mammalian histology.
Basic histology is covered by Histology set I.
The addition of Histology sets II and III gives a comprehensive collection of histology microslides, which should meet the needs of most advanced courses.
No teaching notes are supplied with these sets.
XTEMOS ELEMENT
AJAX PRODUCTS TABS SIMPLE
Worm Sector Type Steering System
Worm & Sector Type Steering System – Actual Working
The working of steering system is shown with the help of actual parts assembled on square iron pipe frame. All the necessary parts of steering system are shown in actual working form. This model helps the student to understand the working of the steering system very easily. It is specially made dissectible for demonstration purposes.
Forced Convection Apparatus
The unit consists of a circular pipe; loosing heat by forced convection to air, being forced through it. Constant heat flux is added to pipe by an electrical heater, provided with input control. The pipe surface temperature is measured at various points along length of pipe. Temperature of air at inlet and outlet of test section are measured. Thus the students can calculate local and overall heat transfer coefficients in forced convection, at various airflow rates and various heat flux values.
SPECIFICATIONS:
1.Test pipe – 32mm NB GI pipe, 500 mm. long, heated by band heater, outside. Centrifugal blower to force air through test pipe with How control valve. 2.Variac 2A, capacity to force air through test pipe with flow control valve. 3.An orifice meter with differential water manometer. 4.Voltmeter and Ammeter to measure heater input. 5.Multichannel digital temperature indicator to measures various temperatures. 6.A technical manual accompanies the unit.SERVICES REQUIRED:
1.Bench area of about 1m. x 0.75 m. at working height. 2.239v, 15A, AC, supply with earthing connection.
XTEMOS ELEMENT
AJAX PRODUCTS TABS ALTERNATIVE
Fashion
Siemens IoT 2040 Gateway Based IoT Development System
SIMATIC IoT 2040 is an Industrial IoT Gateway, reliable open platform for collecting, Processing and transmission data. It helps the students to get the industrial IoT experience and develop Industry 4.0 Projects rapidly.
Specification:
• IoT 2040 Gateway - PLC and sensors of many brands can be integrated through Ethernet & Serial ports. - Open Protocols: Modbus, Profinet, REST or MQTT, AMQP, OPC UA - Based on Intel Quark X1020 ,(x86)@400MHz - Compatible With Open Source Software Arduino IDE and Yocto Linux - High level language support : Java, Python, C/C++ - 1 GB RAM, 8MB Flash ,256KB SRAM - Micro SD card Slot up to 32GB - One miniPCIe Slot for hardware expansion for WLAN/Additional Ethernet Port - Arduino Uno – R3 Compatible - Intel Wi-Fi + Bluetooth Module for 300MB data rate - 2xRS232/422/485(Switchable) - 1xUSB Controller + 1 x Device - 2 x 10 /100 Mbps Ethernet RJ45 • 5 types of sensors such as Temperaturesensor, LDR sensor, Motion sensor, Humidity sensor, Magnetic sensor included to • interface with IoT2040 & add on modules of IoT2040 • The IoT 2040 Gateway can communicate with PLC, DCS using profinet or OPC UA. • Analog Inputs are terminated in a SP7 patch connector • 4Nos of Digital Input SPDT Switch • 4Nos of user LEDs
Plastic Storage Box
We export and trade high quality Plastic Storage Boxes.
These Storage Boxes, made of polypropylene, prove to be an excellent option for storage of different powdered reagents & other material in the laboratory.
Square shape of these boxes helps in saving shelf space.
Available in three different sizes these boxes have polypropylene caps, are autoclavable, provide good chemical resistance & heavy duty service.
| Particulars | Pack (Pcs) | |
|---|---|---|
| Storage Box 250 ml | 12 | |
| Storage Box 500 ml | 12 | |
| Storage Box 1000 ml | 12 |
AED Trainer
Description
The Laerdal AED Trainer 2 offers an affordable alternative for educating the layperson and healthcare provider in the effective use of an automated external defibrillator.Product benefits:
Educationally effective, offers all the essential features necessary for learning appropriate AED use and techniques. Affordable training through the simulation of the HeartStart FR2 AED in appearance and operation. Added instructor flexibility through unique control of the scenario selection by use of the remote control device. Flexible configuration of the device through a scenario builder program that allows the additional creation of custom training scenarios. Cost-effective operation through use of six C-cell batteries.Product features:
Ten pre-configured sudden cardiac arrest scenarios compatible with training programs developed by internationally recognized responder programs. Remote control (optional) for manual scenario selection pause/resume function, AED Trainer 2 volume control, motion artefact, low battery or replace battery, loose electrodes connection, shock able or non-shock able rhythms and error conditions that simulate the red X in the Heart Start FR2’s status display window. Designed for use with the AED Little Anne® and AED Resusci Anne® manikins with Laerdal LINK Technology by providing student feedback as to proper pad placement on the manikins. It can also be used with any other manikin where Laerdal Link Technology is not available. Proper pad placement required in order for the trainer to advance in the scenarios when used with the AED Little Anne or AED Resusci Anne manikins.
XTEMOS ELEMENT
AJAX PRODUCTS TABS ARROWS PAGINATION
SPIRIT LAMP
Spectrometer, Advanced
Description
Vernier reading to 30 seconds of arc. The 175 mm diameter scale is fixed. The table and telescope movements are completely independent of each other and read to 30 seconds of arc by means of double ended verniers and magnifiers. Both rotations have fine adjustment screws. Coarse adjustments can also be made by release of clamping screw. Collimator is mounted on a fixed pillar and is fitted with 175 mm fl. achromatic objective with 32 mm clear aperture and a laterally adjustable slit 6 mm long. Telescope is mounted on a movable pillar fitted with 175 mm fl. achromatic objective of 32 mm clear aperture and x 10 Ramsden eye-piece with a glass cross line graticule. Both the telescope and collimator have rack and pinion focusing and can be adjusted for leveling the axes of both units as well as for adjusting to the axis of rotation. Prism table is marked with lines to assist prism placement and has three table leveling screws. It also has an interchangeable clamping unit for the prism and diffraction grating. Complete with prism clamp, diffraction grating holder and a Tommy bar for adjusting optical axis, In case.
Advanced Universal FPGA Trainer
The universal FPGA trainer consist of a main board with many peripheral like USB Device, Ethernet, Serial ports, Parallel Port, VGA port, Graphics LCD, Switches, LED, ADC etc. This motherboard has 4Nos of high speed connectors for plugging the daughter boards, which contains the FPGA of any manufacturers. Separately 2Nos of 100 pin high speed connectors provided for hardware expansion as plug in boards.
• Industry standard interconnection
- 10 MBPS Ethernet
- USB 2.0 Interface
- Two RS232 ports
- 9 pin D connector
• Memory Sub system
- 8 MB x 16 Bit SDRAM
- 4MB x 16 bit flash EEPROM
- 256KB I2C EEPROM
• Additional Features
- One 240 x 128 graphics LCD
- 16 Nos of dip switches
- 16 discrete LEDs
- 4 digit multiplexed 7 segment LED display
- 4 x 4 matrix keyboard
- One VGA Port at 15 pin D connector
- One PS2 connector for keyboard and mouse
- Reset Switch
- I2C Real time Clock
• Analog Input & Output
- 2MSPS SPI ADC (12 Channel)
- Temperature sensor interface
- One 16 bit Stereo CODEC
• 2 Nos. of 100 pin high speed connectors provided to hardware expansion can be used as hardware bus.
• Multilayer board for superior signal integrity.
• 54 I/O pins terminated at 3Nos of 20 pin connector for external interfacing.
XTEMOS ELEMENT
AJAX PRODUCTS TABS WITH ICONS
PLC-Logo 6 Pack with Demo Panel Trainer Kit
This Training kit based on Siemens model “Logo” PLC controller, is modulator, versatile, scalable & flexible with integrated Ethernet interface. Many features like High Speed configurable Analog Input etc make it as an Ideal PLC for basic training purpose
PLC Specification
• Make : SIEMENS • Model : CPU LOGORCE • Input Supply : 12/24V DC • Timers &Counters : 256 Nos Each • Digital Inputs : 8 Nos • Digital Outputs : 4 Nos • Program Memory : 400 Blocks • 4 Inputs can be configured as Analog Input (0-10V) DC • Optional SD cards for data logging • Ethernet Communication Interface • Networking with up to 8 unitsDemo Panel Specification
• 8 Nos of toggle switches & LEDs provided for Digital Inputs • 6 Nos of LEDs provided for Digital outputs indication purpose • All I/Os are terminated into SP7 connectors for external trainer interfacing • Patch chords provided for interfacing the external trainers • Modules and all the components mounted on an attractive powder coated metal cabinet • Mimic diagram with screen printing provided in the panel
Conical Bottom Centrifuge Tube
Centrifuge tubes with conical bottom are available in two sizes i.e 15 ml. & 50 ml.
Moulded in Polypropylene, these tubes are clear, strong & safe.
These autoclavable tubes are provided with printed graduations on the outer surface.
The built in seal ring in the cap makes these tubes absolutely leakproof.
These tubes can withstand forces upto 7500xG & 12000xG for 15 ml. & 50 ml. tubes respectively.
| Particulars | Pack (Pcs) | |
|---|---|---|
| Centrifuge Tube Conical Bottom - 15 ml | 100 | |
| Centrifuge Tube Conical Bottom - 50 ml | 100 | |
| Centrifuge Tube Box for 15 ml tube | 4 | |
| Centrifuge Tube Box for 50 ml tube | 4 |
Matt White Screen
XTEMOS ELEMENT
AJAX PRODUCTS TABS LOAD MORE PAGINATION
SILICA CRUCIBLE WITHOUT LID
PRODUCT DESCRIPTION
- Crucible is glazed inside and outside.
- Highly resistant to alkalis and hot temperatures
- 50ml capacity
- Outside diameter 55mm, 42mm height
- No lid includedSilica crucible is glazed inside and outside. Highly resistant to alkalis and hot temperature SIZES ARE: 15ML 25ML 50ML 80ML 100ML 150ML
SILICA CRUCIBLE TALL FORM Without Lid, Translucent
XTEMOS ELEMENT
AJAX PRODUCTS TABS CAROUSEL
Round Bottom Centrifuge Tube
Avail from us, a flawless variety of Round Bottom Centrifuge Tube , which is popular for its better quality and precise engineering.
Being one of the chief Exporter and Trader in this industry, the company provides Round Bottom Centrifuge Tube at the most competitive prices.
| Particulars | Pack (Pcs) | |
|---|---|---|
| Centrifuge Tube Round Bottom 16 ml (P.P) | 50 | |
| Centrifuge Tube Round Bottom 50 ml (P.P) | 50 | |
| Centrifuge Tube Round Bottom 16 ml (P.C) | 50 | |
| Centrifuge Tube Round Bottom 50 ml (P.C) | 50 | |
| Cap for 16 ml Centrifuge Tube Round Bottom | 100 | |
| Cap for 50 ml Centrifuge Tube Round Bottom | 100 | |
| Oak Ridge Centrifuge Tubes 30 ml | 12 | |
| Oak Ridge Centrifuge Tubes 50 ml | 12 | |
| Oak Ridge Centrifuge Tubes 100 ml | 12 |
Desert Cooler Trainer
Desert Cooler Trainer works on the principle of evaporative cooling. It is used mostly in the dry hot regions; it consists of a fan which sucks the air from atmosphere through the pads which are used in desert coolers very frequently. The difference in DBT & WBT at inlet and outlet can be measured hence the RH from the charts. Also the amount of water evaporated can be calculated by knowing the water level difference in the reservoir.
SPECIFICATIONS:
1.Fan connected to 1/2 HP motor. 2.Air Cooler Pump to circulate water. 3.DBT & WBT Measuring Thermometer at inlet and outlet. 4.Orifice meter with manometer to measure the air flow. A technical manual accompanies the unit.SERVICES REQUIRED:
1.Floor Area – 1, X 1 m. X 1 -5m. Height. 2.220 V., 15 Amp. , Single Phase Stabilized power supply
Solar Wind 3Φ, 2KW Smart Grid
This consists of 2 Microgrids of 2000W &1000W of power generation connected to a main Power Grid with all the components needed to convert a traditional Grid to a Smart so that many experiments can be conducted on this “Smart Grid”. A 3Φ 3KW isolation transformer with power input from utility grid will act as main grid to which 2 Microgrid will be connected through synchronizing panel. Optionally a commercial 3Φ, 2.5KVA Grid Commercial Solar Power Inverter can be added to this experimental setup. By adding 3Φ, 2.5KVA commercial solar inverter, when the experimental setup is not used by student, it may be used to generate power.
This Advanced Smart Grid Experimental Setup Consists of
• 2 Micro Grids, each 1000W of power generation using Solar, Wind or Hybrid • An Isolation Transformer Coupled to the utility Grid, acts as Main Grid to this Setup • Various other Power Sources • Commercial 3Φ 5KVA Grid Connected Inverter (Optional) • Optional Components for the Smart Grid Setup • DSP /FPGA Controller for PE, SG, PS Applications • Other Add ons • Components for Building 10/25KW Smart Grid Power Generation • IoT Based Data Acquisition.Solar Wind Grid Connected 3Φ, 2KW Smart Micro Grid
• Main Frame • 1KW Solar PV Module with Stand • Wind Turbine • DC-DC Boost Converter • 120V Battery Bank - 12V x 100AH x 10 Nos • 2KW Bi-Directional DC-DC Buck-Boost Converter for Charging battery • 2KW 3Φ Inverters • DSP/FPGA Controller • Microcontroller based Protection Relays • Smart Energy Meter • Synchronizing Panel • Three Phase RL Load 2KW • PLC with SCADA Software • 14 Channel PC based Power Quality Analyzer (Optional)
CNC Lathe Trainer1
CONTROLLER:
Type of control system: PLC based system Main Spindle Drive : AC Motor with VFD Z and X Drives : Stepper drive with RAMP function Input to Stepper Motor : Optically Isolated Motor Drive :TTL Compatible Run Speed Control : Computer controlled through software Interpolation : Linear / Circular / Parabolic Cycles Used :G,M,S,T,F,I,K,M,F Cycles : Circular Interpolation / Canned Threading : Straight / Taper Power Devices : Short Circuits and over Temperature Protected Real Time Tool Path Simulation : ProvidedMACHINE DETAILS:
Center height : 100mm Swing over Carriage : 80mm Distance between Centre : 250mm Longitudinal Travel : 250mm Weight : 350 kg Dimension in mm : 1100 x 750 x 1700 Rapid Travel : 500mm/min Resolution X & Z Axis : 10micron Dt. Motor Power : 40V – 4A Lubrication : ManualSPINDLE:
Spindle Speed : Continuous Variable Spindle Power : 1.5 HP Inside Taper : MT3 Speed Range : 100 to 3000 RPM
