XTEMOS ELEMENT
AJAX PRODUCTS TABS
Polariser and Analyser (Polaroid)
Force Table
To verify the law of composition and resolution of forces consisting of a aluminium table 40cm in dia.
its raised rim has a engine divided scale, graduated in 360° mounted on heavy vertical support rod & tripod base provided with leveling screws.
Body under study in a ring in center of the table fastened by cords passing over four pulleys attached with the table.
Complete with four pulleys, four weights hangers twelve weights (2x10gm, 2x20gm, 4x50gm, 4x100 gm.)
Human Torso With Head
Description
Full size, 10 parts, without sterno – abdominal wall but with ribs, sternum and clavicle with their attachments. Thoracic and abdominal organs, individually detachable lungs, stomach, liver, intestine, heart, which is further sectioned in two parts. Half of skull cap is removed, and brain can be taken out, exposing the interior of the skull. Sectioned head and neck depicts internal organs of the region, sexless, on base, with key card.
Rabbit Holder
XTEMOS ELEMENT
AJAX PRODUCTS TABS SIMPLE
Two Stroke Petrol Engine Model
Aquatic Net
Pin Fin Appatatus
The apparatus consists of a channel in which the pin fin is tested in both natural as well as forced convection. The channel is connected to the suction of blower. The blower is operated to touch the pin fin in forced convection only. In natural convection, the window above the pin fin is kept open to the atmosphere. Five thermocouple tapings are given along the length of the fin. Thus the temperature distribution along the length can be distinguished. Also natural and forced heat transfer co-efficient, effectiveness, etc. can be found out.
Specifications:
1.Three pin fins- a) M. S. b) Brass c) Al 2.Channel- 150mm x 100mm x 1000mm 3.Blower – run by f.h.p. motor. 4.Orifice meter along with water manometer to measure airflow. 5.Voltmeter and ammeter to measure power input. 6.Cr- Al thermocouple with 6 tapings along with temperature indicator. 7.Dimmerstat to control power input. 8.A band heater to heat the pin fin. A technical manual accompanies the unit.Services required:
1.220v, stabilized single phase supply along with earthing Connection. 2.Floor area 2m x 1m x 1m height.XTEMOS ELEMENT
AJAX PRODUCTS TABS ALTERNATIVE
Fashion
Spectroscope
Description
Hand held simplest form of spectroscope. It can be used to get a general idea of the correlation between wavelength and observed color. A diffraction grating is used which spreads the incident light into its component wavelengths. An illuminated reference scale against which the spectrum may be viewed is also provided. Spectroscope (Wooden)
Cortex M4 Development Board
Cortex M4 is an ideal replacement solution for the traditional Microcontroller & DSP Processors. Vi-S32 based on ST Microelectronics cortex M4 processor offers many features for Embedded Real Time world. The full range of hardware features on the board is provided to help you to evaluate and develop many applications. STM32 Embedded target enables systems and software Engineers to quickly deploy their application models in Matlab& Simulink to Cortex M4 ARM.
Specification
• STM32F407VGT6 microcontroller high performance 32bit ARM Cortex M4. • Operating upto 168MHz • 196Kbytes of SRAM • 2.4 MSPS Analog to Digital Converter • Two Nos. of Potentiometer interface for ADC input. • Two Nos. of DAC with simultaneous conversion • 1MB On-Chip Flash. • 4 Nos. of User LEDs, Relay Interface. • 8 way dipswitch for user input • I2C Based 2 digit 7 Segment display interface. • 4 keys keypad, Stepper Motor driver interface. • USB OTG FS with micro AB connector interface. • RTC with battery backup • I2C EEPROM device interface • SPI based temperature sensor interface • 1 Gbyte Micro SD Card interface • RS232 UART interface at a pin D connector/USB connector • CAN 2.0 lines are terminated at 9 pin D female connector • 3.2inch 240 x 320 TFT color LCD with Touch Screen • 10/100Mbps Ethernet interface • Extension header for I2C, SPI & CAN • Camera Interface
Synchromesh Gear Box 4 Forward 1reverse
Synchromesh Gear Box – 4 Forward & 1Reverse Actual Cut Section
The working of gear box is shown with the help of actual parts assembled on square iron pipe frame. All the necessary parts of gear box are shown in actual working form. This model helps the student to understand the working of the gear box very easily. It is specially made dissectible for demonstration purposes.
Slide Box
We are the major Exporter and Trader of superior quality Slide Boxes .
These Slide Boxes are durable, compact & provide utmost protection to 1" x 3" slides.
Heavy walls will not warp, splinter or crack.
Our Slide Boxes are unaffected by humidity and are thoroughly insect proof.
| Particulars | Pack (Pcs) | |
|---|---|---|
| Slide Box - 25 Slides | 12 | |
| Slide Box - 50 Slides | 12 | |
| Slide Box - 100 Slides | 6 |
XTEMOS ELEMENT
AJAX PRODUCTS TABS ARROWS PAGINATION
Bottle Cap Sealing Machine
Specifications
Bottle Cap Sealing Machine which is used by the industries for sealing the cap of the bottles. It is supplied with complete electric fittings accessories. Finds usage in pharmaceutical, chemical and food & beverage industries, the offered range is available in different specifications, in order to meet the variegated expectations of our valuable customer. Our provided Bottle Cap Sealing Machine is tested by the team of our professionals. Furthermore, our clients can avail the entire range from us at market leading prices. (a) Hand operated. (b) Electrical operated.
PH METER
Product Description
Due to our wide expertise, we are involved in manufacturing and exporting Digital pH Meter. The leading technology we have incorporated in this equipment results in accurate measurement of pH balance. Widely demanded in pharmaceutical, chemical, and food and beverage industry, this digital pH meter is available at a competitive price for our prestigious clients. Features:- Sleek design
- Accurate results
- Digital display
- Digital PH METER
- Max Make
- E.I. Make
- PH Electrode (Glass) Routine
- PH Electrode (Gell Filled) Unbreakable
- Pen type PH METER
Transducer Trainer
Specification
• RTD acts as a temperature sensor • Strain gauge based load cell • Linear variable resistive transducer • LDR, Photo diode, photo transistor • Precision servo potentiometer • Inductive type proximity sensor • Heat source, Filament lamp, Buzzer • 3½ digit LED display • Analog type 10V Center-Zero meter • Inverting and Non-inverting amplifier • Amplifier with Gain and offset control • Instrumentation and summing amplifier • Low pass filter • Precision Rectifier • Timer and buzzer oscillator • Electric switchXTEMOS ELEMENT
AJAX PRODUCTS TABS WITH ICONS
Lagged Pipe Apparatus
Lagged Pipe Apparatus:
The apparatus consists of three concentric pipes mounted on suitable stand. The space between innermost and the middle pipe is fifed with a lagging material and the space between the middle and the outer most is filled with and other lagging material. The lagged pipe is heated with a cartridge heater inserted at the axle length of the pipe. Voltmeter and ammeter on the panel can measure the input to the heater. The intermediate temperatures can be measured by the thermocouples attached at the surfaces of the pipe. Thus the resultant conductivity of the materials can be found out.
SPECIFICATIONS:
1.Pipes : a)Gl pipe (innermost) – 6 cm. (Outer Diameter). b) Gl Pipe (Middle) – 8.5 cm. (Mean Diameter) c)G! Pipe (Outermost) – 10.7 cm. (inner Diameter) d)Length of pipes 1 Meter. 2.Heater : Nichrome wire cartridge heater placed centrally, of suitable capacity. 3.Control Panel : a)Single Phase Dimmerstat – 1 No. b)Voltmeter (0 – 250V) – 1 No. c)Ammeter (0- 2A) – 1 No. 4.Temperature Indicator : Multichannel Digital Temperature Indicator ranging (0 – 300 C) using Cr/AI ThermocouplesServices Required:
1. A.C. Single Phase 230 V electric supply 2. Floor Area-1.5 Meter X 1 Meter X 0.5 Meter High
Lens Holder Wooden
Calorimeter Stirrer, Copper
XTEMOS ELEMENT
AJAX PRODUCTS TABS LOAD MORE PAGINATION
SILICA CRUCIBLE WITHOUT LID
PRODUCT DESCRIPTION
- Crucible is glazed inside and outside.
- Highly resistant to alkalis and hot temperatures
- 50ml capacity
- Outside diameter 55mm, 42mm height
- No lid includedSilica crucible is glazed inside and outside. Highly resistant to alkalis and hot temperature SIZES ARE: 15ML 25ML 50ML 80ML 100ML 150ML
SILICA CRUCIBLE TALL FORM Without Lid, Translucent
XTEMOS ELEMENT
AJAX PRODUCTS TABS CAROUSEL
Coriollis Component Of Acceleration
This set up is designed to study coriollis component of Acceleration of a slider crank Mechanism. The apparatus uses hydraulic analogy to represent the rotating slider. It consists of a rotating block with two arms in opposite direction. These tubes can be rotated at various speeds by using a swinging field motor, which also acts as a dynamometer to measure torque applied to rotating tubes. A Perspex window on top cover helps to visualize the process. Rotameter is used to measure water flow rate through tubes. Water is circulated by small monoblaock pump.
Specifications:
1.Main Tank with fiberglass lining. 2.Rotating Arms 9/6 mm dia, 300 mm long. 3.Motor – Swinging field, D.C., 0.5 HP. 4.Rotameter 5.Monoblock Pump 6.Control Panel comprising of – (i) Speed Control Unit. (ii) Speed Indicator. (iii) Necessary switches. 7.Rigid support frame.Range of Experiment:
Coriollis Component of Acceleration can be determined at various speeds of rotation and water flow rates.Service Required:
1.A.C. Single Phase .230 V. stabilized supply. 2.Floor Space -1.5 m X 1.5 m.
Rocks Collection
Description
A comprehensive collection of igneous , metamorphic and sedimentary rocks, in wooden box with partitioned tray containing 50 specimens, each nominally numbered and enclosed in a transparent plastics bag. Specimens may be removed from bags for detailed examination. Each specimen is labelled also on the inside of the box lid, indicating the geological name.
Theramal Conductivity Of Insulating Slabs
The apparatus consists of a slab assembly. The main Heater and a radial guard heater are sandwiched between copper plates. The specimen in the form of slabs of equal thickness are placed on either sides of heaters and cooling plates through which water is circulated are on the other Sides of the specimen. The radial guard heater ensures all heat of the main heater to pass axially through the specimens which is collected by cooling plates. By knowing the temperatures and Heat input, thermal conductivity of specimen can be calculated. The test set up is enclosed in an enclosure with insulation inside to provide undisturbed Surroundings. The design style of the apparatus is similar to as recommended in INDIAN standard. The difference is in sizes.
SPECIFICATIONS:
1.Heaters: a)Main heater plate 110 mm dia. with mica heater Sandwiched between copper plates. b)Radial guard heater plate I.D. 120mm and OD 200 mm mica heater sandwiched between copper plates. 2.Water circulated cooling plates -2 nos. 3.Dimmerstat-2 A capacity – 2 nos. to independently control Inputs to the heaters. 4.Measurements – A voltmeter and an Ammeter with selector switches to measure inputs,Multichannel digital temperature indicator to measure Temperatures at various points, having 0.1 °c least count. A technical manual accompanies the unit.SERVICES REQUIRED:
1.230 V, A.C. stabilized supply along with earthing connection. 2.Water supply of about 4-5 lit/min. 3.Bench area 1m x lm x O.5m height.
SENIOR RESEARCH BIOLOGICAL MICROSCOPE
BIIC-220 Series
 Micron BMC-220 is the newly introduced series o[educational Microscope which extend top quality optics and uncompromising performance for educational and routine research work.
Features :
- Mechanical tube length 160 mm.Â
- 45 inclined with 360 degree rotatable binocular head.
- Co-axial built in Mechanical stage 140 x 140 mm with fine vernier graduation, designed with convenient coaxial adjustment forjerk free smooth slide manipulation through 55 x 75 mm.Â
- Dust proof quadruple/ quintuple ball bearing revolving nose piece with positive click stops.
- Co-axial coarse & fine focusing adjustment knobs on ball bearing guide ways. Fine motion, graduated to .002 mm.Â
- Staple Grey, chemical resistant, back-on finish.
- Adjustable focus lock prevents damage to valuable slide and objectives.
Linen Tester
Description
These are collapsible pocket magnifiers. The optical system is a single element, glass Double Convex Lens. The housing is made of machined, black high grade plastic for a high finish look. These magnifiers fold flat to fit in your pocket. Scales are etched on the inner faces of the viewerÂ’s base.
