XTEMOS ELEMENT
AJAX PRODUCTS TABS
Tablet Making Machine (Hand Operated)
Details
Single punch automatic compression and injection device with each revolution of the wheel drive automatic feed and remove of tablets. Built on heavy cast body with centric pressure system SS hoper provided and connected by a rubber tube easy setting for thickness and hardness of tablets with nuts and locknuts.Features
Easily rotating wheel for making tablets. Compressing lever for adjustable harness of tablets. Adjustable lower punch for adjusting the thickness. Stainless steel day and punch size 6, 9, 12 mm. Electrical model can be provided in same with ½h.p motor.
Gear Pump Test Setup
DESCRIPTION:
The Set-up is designed to study the performance of Gear Pump. The Set-up consists of a Gear Pump having a pair of meshed gears coupled with electrical motor, supply tank, measuring tank & pipe fittings for closed loop oil circulation. Pressure and Vacuum Gauges are connected on delivery and suction side of pump for the purpose of measurement. The flow rate of water is measured using measuring tank and stop watch provided.EXPERIMENT:
Ø To determine overall efficiency and pump efficiency of the Gear Pump Ø To plot Head vs. Discharge, Pump efficiency vs. DischargeFEATURES:
Ø Closed loop water circulation Ø Compact & stand alone set-up Ø MS Excel sample calculation program on demand Ø Stainless Steel tanks and wetted parts Ø Superb painted structure Ø Simple to Operate & MaintainUTILITIES REQUIRED:
Electric Supply: – Provide 230 +/- 10 VAC, 50 Hz, Single Phase Electric Supply with proper earthing. (Neutral – Earth voltage less than 5 VAC) 5 A, three pin socket with switch for pump. Oil Supply: Oil @ 30 Ltrs. (Optional extra cost)TECHNICALS SPECIFICATIONS:
Ø Pump : Gear Pump with pair of meshed gears Capacity 1 HP,Speed 1500 RPM (max.), Head 5 Kg/cm2 (max.) Ø Drive : AC Motor with step cone pulley arrangement for 3 prefixed speed DC Motor with DC Drive along with (non-contact type Digital RPM Indicator Ø Supply Tank : Capacity 30 Ltrs. Ø Measuring Tank : Capacity 20 Ltrs. fitted with Piezometer Tube & Scale Ø Piping : GI / PVC Ø Stop Watch : Electronic Ø Control Panel : With required electrical instrumentation (The whole Set-up is well designed and arranged in a good quality painted structure.
XTEMOS ELEMENT
AJAX PRODUCTS TABS SIMPLE
Coriollis Component Of Acceleration
This set up is designed to study coriollis component of Acceleration of a slider crank Mechanism. The apparatus uses hydraulic analogy to represent the rotating slider. It consists of a rotating block with two arms in opposite direction. These tubes can be rotated at various speeds by using a swinging field motor, which also acts as a dynamometer to measure torque applied to rotating tubes. A Perspex window on top cover helps to visualize the process. Rotameter is used to measure water flow rate through tubes. Water is circulated by small monoblaock pump.
Specifications:
1.Main Tank with fiberglass lining. 2.Rotating Arms 9/6 mm dia, 300 mm long. 3.Motor – Swinging field, D.C., 0.5 HP. 4.Rotameter 5.Monoblock Pump 6.Control Panel comprising of – (i) Speed Control Unit. (ii) Speed Indicator. (iii) Necessary switches. 7.Rigid support frame.Range of Experiment:
Coriollis Component of Acceleration can be determined at various speeds of rotation and water flow rates.Service Required:
1.A.C. Single Phase .230 V. stabilized supply. 2.Floor Space -1.5 m X 1.5 m.
Demonstration Meter Inter Scale
Description
Housed in a ABS plastic case 300x150x300 mm with glass front and rear. Moving coil type with accuracy of + 2.5%. Basic sensitivity of meter is 5 mA, 100mV f.s.d. The meter can be used to demonstrate the working principle of AC or DC ammeters or voltmeters with the interchangeable plastic scales. DIFFERENT DIALS ARE AVAILABLE.
Reciprocating Compressor Actual Cut Section
This model will be made out of original parts. The model will be suitably sectioned to demonstrate the internal construction details showing the minute information, and working of the same, the model will be suitably painted and mounted on a metal or wooden base & supplied with key card & very interesting literature regarding working of the same.
XTEMOS ELEMENT
AJAX PRODUCTS TABS ALTERNATIVE
Fashion
Airway Intubation Model
Description
The Difficult Airway Management Simulator offers a realistic airway management training with 24 various difficulty levels including 3 different mouth openings, 2 neck flexibility options, 2 positions for the vocal codes and an inflatable tongue.Training Skills:
Airway opening techniques (head tilt, jaw thrust) Bag-Valve-Mask ventilation Pre intubation airway assessment "Sniffing position" Pressurization of external larynx to improve the laryngeal view Intraoral/intranasal intubation Use of oropharyngeal airway (OPA) Use of nasopharyngeal airway (NPA) Use of laryngeal mask airway Use of video laryngeal scope Use of tracheal intubation scope Confirmation of successful ventilation by thoracic and abdominal movement Feedbacks on incorrect procedures including esophagus intubation and unilateral intubation Securing the tube in place with tapes or Thomas endotracheal tube holderTraining Model Includes:
1 manikin 3 upper incisions 1 lubricant 1 50ml syringe Size: 27.6 x 15.4 x 9.9 inRecommended Equipment:
Macintosh laryngoscope: blade size 3, 4 Tracheal tube: internal diameter 7.0-7.5mm Laryngeal mask Air-Q: size 3.5 LMA supreme: size 4 I-gel: size 4
Weighing Bottle with Interchangeable Stopper
Blood Collection Vials (VACUTAINER) Plain/EDTA
Blood collection and storage is done is special tubes which allow the preservation of the blood sample over long periods.
These tubes can be made of glass or plastic and the caps of these vials are coloured to indicate the additives in them.
Some of the additives are anticoagulants such as EDTA, sodium citrate or heparin.
Other substances include preservatives. The containers containing coagulants are capped with gold, red or orange caps.
The ones containing anti-coagulants are green, which contain heparin, purple or lavender indicates ones which contain EDTA, grey capped tubes contain sodium fluoride or oxalate. Blood collection tubes (also called as vacutainers) are extensively used in hospitals, medical centres and diagnostic centres.
In biological labs, it is used in experiments like haemolysis etc.
Non Vacuum Vials (Pk of 100)
Vacuum Vials (Pk of 100)
XTEMOS ELEMENT
AJAX PRODUCTS TABS ARROWS PAGINATION
Balance
Larynx, 2 Parts
Behaviour Of Column Struts Apparatus
Apparatus consist of four spring steel columns which are put along a vertical wooden board. These four columns have different end conditions as below:
1. Both ends pinned
2. Both ends fixed
3. One end pinned and other fixed
4. One end fixed and other end free
Apparatus to be supplied should be complete with a supporting stand and a set of weights.
XTEMOS ELEMENT
AJAX PRODUCTS TABS WITH ICONS
Crucibles Porcelain Gooch
REDWOOD VISCOMETER
PRODUCT DESCRIPTION
Oil & Petroleum Testing Instruments is widely acknowledged for its high functional efficiency, excellent results, accuracy, robustness, ability to withstand extreme working conditions and low maintenance requirements. Technically advanced and durable, these instruments are offered at industry leading prices in different specifications as per the requirements of the clients.
Car Chassis Rear Wheel Drive Actual Cut Section Motorised
Car Chassis Rear Wheel Drive Actual Cut Section – Motorised
4 Stroke 4 Cylinder Petrol Engine With Clutch, Gear Box, Propeller Shaft, & Rear Axle Assembly With Differential Gear
The chassis of the four stroke four cylinder engine cut section model. The cut section model is constructed such that all the following systems can be demonstrated in working conditions.
ENGINE:
Maximum parts and accessories of an engine like cylinders, cylinder head, inlet and Exhaust manifolds, FIP, injectors, self-starter, alternator, water pump, radiator, etc., are sectioned to show the internal constructional details. The complete sectioned model is coupled with FHP 220/230V A.C single phase motor through a Reduction drive unit.TRANSMISSION SYSTEM:
This system consists of a Clutch and four speed gearbox assembly, the casing of which is suitably cut to demonstrate its operation. The gearbox is coupled to Differential gear box with propeller shaft and the different coupling used for this transmission can be demonstrated. The Differential gear box is also cut so as to clearly to demonstrate its complete operating principle. The gear shifting including the forward and reverse gear operation can be clearly shown. The speed variation and the rotation of the Differential gear box can be seen while gear shifting. By running the motor connected to the engine assembly the entire system with gear box, rear axle etc. can be demonstrated in running. FUEL SYSTEM: The Fuel tank is cut to expose the mounting of the level sensor and the position of Fuel section. The system is complete with mechanical Fuel pump. EXHAUST SYSTEM: It consists of Exhaust Manifold and silencer in cut section to explain internal construction. LUBRICATION SYSTEM: It consists of the engine Lubrication system along with the Lubrication oil pump is suitably sectioned. SUSPENSION SYSTEM: This will explain both the Hydraulic Suspension systems at the front and the leaf spring Suspension at the Rear. One of the hydraulic arrangements of Suspension mechanism is highlighted (with shock absorbers) and explained cut sectionally.BRAKING SYSTEM:
The Hydraulic or Air circuit Brakes. The movement of the Brake Shoes on operating the brake pedals can be seen in the area where the Brake drum is cut. The front and rear brakes will be operational. STEERING MECHANISM: The can be seen and included in the Steering wheel. Steering gear box and coupling of the same to the wheels will be shown by rotating the steering wheel, the operation of the steering system can be demonstrated. The entire system will be mounted on the chassis, and suitable mounting option with caster wheels will be provided for easy movability.
Mechanical Training Model
Description
Highly useful for demonstrating the most fundamental and frequently used mechanism. Very useful for engineering students. All the components are made of high degree of precision. These modules are assembled on transparent perspex sheets to facilitate teaching. Easy to assemble or disassemble.XTEMOS ELEMENT
AJAX PRODUCTS TABS LOAD MORE PAGINATION
SILICA CRUCIBLE WITHOUT LID
PRODUCT DESCRIPTION
- Crucible is glazed inside and outside.
- Highly resistant to alkalis and hot temperatures
- 50ml capacity
- Outside diameter 55mm, 42mm height
- No lid includedSilica crucible is glazed inside and outside. Highly resistant to alkalis and hot temperature SIZES ARE: 15ML 25ML 50ML 80ML 100ML 150ML
SILICA CRUCIBLE TALL FORM Without Lid, Translucent
XTEMOS ELEMENT
AJAX PRODUCTS TABS CAROUSEL
Portal Frame Apparatus
DESCRIPTION:
Portal Frames used for the measurement of horizontal reaction are made stiffer by using M. S. flats rectangular cross section (10mm thick and 40mm wide). All are true to shape. The ends can be other fixed of hinged as desired. The end at which horizontal reaction, is to be measured, is provided with ball bearing rollers, which easily rolls on a smooth rolling platform. At the roller end a chord is attached which is connected further to spring balance. The spring balance records the horizontal reaction, for the measurement of slope and deflection. Both the columns of the portal frame can be clamped (fixed) or pivoted (hinged) and required.EXPERIMENT:
• To study the behavior of a portal frame under different end conditions.TECHNICAL SPECIFICATION:
• Apparatus made up of M.S. plate of rectangular section of 3mm thick x 40cm wide. • Frame is provided with a provision to achieve different end conditions viz. hinged, roller & fixed. • The size of portal will be 40cm x 60cm. Portal may also have a provision for pulley arrangement and hook arrangement for horizontal loading at different positions. • Apparatus is to be supplied complete with a supporting stand and a set of weights • Electronic load cells, displacement cell and Electronic Control Unit (ECU) provided with apparatus. • Software for digital calculations to easily performs by students.OPTIONAL ACCESSORIES:
• PC/Laptop Set.
Slide Storage Rack
We are engaged in providing Slide Storage Rack can hold 100 slides which are recognizable through the numeric indexing.
Spacing between the slots provides adequate backward & forward movement of slides for convenient recognition.
Made of ABS, the transparent cover provides excellent view of the slides stored inside.
Material : Acrylonitrile Butadiene Styrene
| Particulars | Pack (Pcs) | |
|---|---|---|
| Slide Storage Rack - 100 Slides | 6 | |
| Float Rack | 12 |
Comparative Terrain Model
Description
Set of 2 landform models, each includes an overlay representing ancient mountain forms that can be removed and compared with the base model to show changes millions of years later. Cross section shows basic mountain types, volcanic fault block, glaciated domes and folded mountains with lesson plan, size 45 x 60 cm.
Worm Roller Type Steering System
Steering System – Actual Working
Manual Steering System
Type – Worm & Roller Type Steering System – Actual Working
The working of steering system is shown with the help of actual parts assembled on square iron pipe frame. All the necessary parts of steering system are shown in actual working form. This model helps the student to understand the working of the steering system very easily. It is specially made dissectible for demonstration purposes.
PATHOLOGY INCLINED MONOCULAR MICROSCOPE
PRODUCT DESCRIPTION:
OBSERVATION HEAD: MONOCULAR Inclined at 45° and Rota table 360º with perfectly centered Quadruple BAL Bearing revolving nose piece. OBJECTIVE- 4/5x, 10x, 40/ 45x, 100x (oil). EYE PIECES- 10x WF (one), Huygenian 5x or 15x (Any one)MECHANICAL STAGE: Double plate 130x140 mm Low drive mechanical stage for X & Y movement with Sub stage bright field condenser N.A. 1.25 & iris diaphragm with built in swing out filter holder and up-down movement through rack & pinion. FOCUSING SYSTEM: Separate Coarse & highly sensitive fine movement mechanical graduated to 0.02mm. With locking device. EXTRA LARGE BASE: To support the robust arm, has built in with LED cooled bright Illumination or 6V 20 W HALOGEN LAMP with soft start continuously variable intensity controlled regulator & quick change bulb provision. PACKING: Microscope supplied one Plano concave mirror for use in day light, duster, cover & instruction manual.
