XTEMOS ELEMENT
AJAX PRODUCTS TABS
Mini Rotary Shaker
Body made out of thick mild steel finished with powder coating.
PMDC motor used for shaking.
Platform size 300x300 mm. S.S. platform consists of 9x250ml conical flask lotus type clamps.
RPM range 50-250 RPM, Electronic variable control, with 0-60 min mechanical timer.
Mini Rotary Shaker
Workable on 220 V AC 50Hz single phase.
Optional
Digital R.P.M. indicator Digital timer (0-99 min.)Siemens IoT 2020 Gateway
Specification:
• SimaticIoT 2020 Educational Intelligent gateway • Intel Quack Soc x 1000 • 400MHz operating frequency • Micro SD card slot, upto 32GB • 512MB RAM, 8MB Flash, 256KB SRAM • One USB controller and one USB device • FTDI USB to serial Interface • One no of 10/100Mbps Ethernet • Arduino Uno R3 compatible expansion slot • One mini PCIe expansion slot for WLAN/additional Ethernet port • Yocto V2.1 based Linux operating system • Input supply 24V DC • Programming in high level language • Support for various protocols like Modbus RTU, POC UA and cloud protocols like MQTT/AMQPHydraulic Bench Apparatus
OBJECTIVE:
To conduct the experiment of hydraulic bench, with separate experiential set ups i.e. Hydrostatic Pressure, Flow over Weirs, Bernoulli’s Theorem, Flow meter Demonstration, Impact of jet and Orifice Discharge etc. which are accessories of the Hydraulic Bench.DESCRIPTION OF APPARATUS:
The set up is a self-contained, water recirculation unit provided with a top tray, sump tank and a measuring tank. Drain valve and over-flow are provided on the sump tank. A centrifugal pump is fitted for water circulation. Flow control valve and bypass valve is fitted in water line to conduct the experiment at different flow rates. Flow rate of water is measured with the help of measuring tank and stop watch. Measuring tank is provided to measure the discharge. Drain valve is provided in the measuring tank to empty water in sump tank after measuring discharge. Separate level indicator and scale is provided to read the level of water in the measuring tank.UTILITIES REQUIRED:
1.Water Supply (Fill approx 250 Ltrs Initially). 2.Drain Required. 3.220 V AC, 50 Hz, single phase electric supply source. 4.Floor area 1.75 m x 1.50 m.SPECFICATION:
1. Top Tray : 1060 mm x 650 mm. 2.Pump : 1 HP 3.Flow Measurement : Using measuring Tank (Material SS) 4.Tank : Capacity 40 Ltr. 5.Sump Tank : Capacity 120 Ltr. Material SS. The whole set-up is well designed and arranged in a good quality powder coating painted structure.XTEMOS ELEMENT
AJAX PRODUCTS TABS SIMPLE
Tangent Galvanometer
Dicot Stem Anatomy T. S. & L. S.
Description
This model shows the transverse and longitudinal section of a dicotyledonous stem in which case the cambium ring has been formed but no secondary growth has yet taken place. Useful model for study of epidermis, lentice , cork layer, cork cambium, cortical parenchyma ,starch sheath, medullary rays, phloem, sieve plate, sieve tube, phloem parenchyma and inter fasicular cambium ,xylem, pitted vessels, bordered pitted vessels, annular vessels, spiral vessels, pith etc. Mounted on base, with key card.Mirror, Plane
Rain Gauge
Description
Rain gauge is designed to measure the precipitation. This small Version consisting of upper and lower housing part, measuring cylinder; Housing made of stainless steel, orifice rim made of brass. Type 7019.0000 can be supplied with a receiving area of 100 cm2. (This type is not conforming to meteorological standards). • Receiving area : 100 cm². • Rain measure (graduated glass) : 250 cm³. • Measuring range : 0 t0 25 mm precipitation (relative to a receiving area of 100 cm²). • Graduation : 1/1 mm precipitation. • Dimensions : dia 115 mm; height 300 mm. • Weight : approx. 0.8 kg.XTEMOS ELEMENT
AJAX PRODUCTS TABS ALTERNATIVE
Fashion
Optical Bench, wooden
Description
A wooden base board with one meter scale divided into mm with following accessories: One each White face object and receiving screens each 150 x 100 mm with aperture mounted on wooden base with an index mark. Two plane mirrors 150 x 100 mm mounted as above. One lens holder V shaped, wooden. One needle vertically mounted in a short wooden rod on base. One candle holder on base. The components have the same optical center height.Three Step Inductor
Description
This three step inductor consists of a coil of enamelled copper wire wound over an insulated spool. The coil consists of 4 layers of 200 turns each. The tappings at 200, 400 and 800 turns are brought out at 4 mm sockets. The output inductances at these tappings are as follows. No. of turns Resistance 200, Inductor 0.3 mH, Resistance 0.6Ω No. of turns Resistance 400, Inductor 1.2 mH, Resistance 1.2Ω No. of turns Resistance 800, Inductor 5.0 mH, Resistance 2.6Ω. One can easily change the inductor value of the instrument on just inserting a soft iron core inside the bobbinXTEMOS ELEMENT
AJAX PRODUCTS TABS ARROWS PAGINATION
FLASK TONG
Plates For Simple Cell
Rocking Microtome
Description
A sectioning equipment, economical and simple, yet providing all facilities of a standard rotary microtome. The internal mechanism is fully enclosed in a sturdy metal case, for protection against dust and grit & is driven by a handle which can be locked in position. A ball & socket type movement permits use of the entire knife edge. With a feed range of 1 to 25 microns in steps of 1 micron. Supplied complete with a set of three object holders, one razor 120 mm with back and handle, one honing plate, one bottle of oil for lubrication, dust cover and wooden cabinet.Burner Bunsen – Simple, LPG
XTEMOS ELEMENT
AJAX PRODUCTS TABS WITH ICONS
N-P-N Transistor Unit
Lens Holder Wooden
XTEMOS ELEMENT
AJAX PRODUCTS TABS LOAD MORE PAGINATION
SILICA CRUCIBLE WITHOUT LID
PRODUCT DESCRIPTION
- Crucible is glazed inside and outside.
- Highly resistant to alkalis and hot temperatures
- 50ml capacity
- Outside diameter 55mm, 42mm height
- No lid includedSilica crucible is glazed inside and outside. Highly resistant to alkalis and hot temperature SIZES ARE: 15ML 25ML 50ML 80ML 100ML 150ML
SILICA CRUCIBLE TALL FORM Without Lid, Translucent
XTEMOS ELEMENT
















