XTEMOS ELEMENT
AJAX PRODUCTS TABS
Tool Dynamometers
A machine-tool dynamometer is a multi-component dynamometer that is used to measure forces during the use of the machine tool. Empirical calculations of these forces can be cross-checked and verified experimentally using these machine tool dynamometers.
(1) Milling Tool Dynamometers
(2) Grinder Tool Dynamometers
(3) Lathe Tool Dynamometers
(4) Drilling Tool Dynamometers
Crucible with Lid High Form
Description
Chemical porcelain crucibles are glazed inside and out, except outside bottom and rim. Crucible covers are completely glazed except for rim. For use in temperatures up to 1150 C (2102 F). Not recommended for minerals or metals.Capacity :
100mlHeight :
2.13 inch (54mm)Top Outside Diameter :
2.56 inch (65mm)
Resistance Coils
XTEMOS ELEMENT
AJAX PRODUCTS TABS SIMPLE
Expansion Model of Human Teeth
Aluminium Tripod Stand Dual Lock
Description
We are supply and Export of aluminum tripod stands that are procured from the trustworthy sources, who make these using high quality raw material such as brass and aluminum. These products are also available in a powder coated finish and are especially developed for providing maximum stability and strength. Moreover, all our products are available in various sizes, shapes and designs to fulfill the diverse needs of our clients.
Multi Stage Centrifugal Pump Test Setup
DESCRIPTION:
The Set-up is designed to study the performance of Multi Stage Centrifugal Pump. The Set-up consists of a Multi Stage Centrifugal Pump coupled with DC motor & drive, supply tank, measuring tank & pipe fittings for closed loop water circulation. There are 2 separate pumps connected to DC Motor and drive and can be connected in series and parallel to stimulate different combinations. Pressure and Vacuum Gauge are connected on delivery and suction side of each pump for the purpose of measurement. Swinging Field Dynamometer arrangement for direct torque measurement using dial type spring balance is made for individual pump. The flow rate of water is measured using measuring tank and stop watch provided.EXPERIMENTS:
1.Speed Vs Discharge 2.Head Vs Discharge at various speeds 3.Efficiency curves at various speed and headsFEATURES:
1.Closed loop water circulation 2.Compact & stand alone set-up 3.MS Excel sample calculation program on demand 4.Stainless Steel tanks and wetted parts 5.Superb painted structure 6.Simple to Operate & MaintainUTILITIES REQUIRED:
1.Electric Supply: – Provide 230 +/- 10 VAC, 50 Hz, Single Phase Electric Supply with proper earthing. (Neutral – Earth voltage less than 5 VAC), 5 A, three pin socket with switch for pump. 2.Water Supply: Tap water connection ½” BSP. Distilled water @ 80 Ltrs. (Optional extra cost)TECHNICAL SPECIFICATIONS:
1.Pump (2 Nos.) : Kirloskar, Capacity 1 HP Speed 2800 RPM (max.) Head 12 m (max.) 2.Drive : DC Drive along with non-contact type Digital RPM Indicator 3.Supply Tank : Capacity 150 Ltrs. 4.Measuring Tank : Capacity 100 Ltrs. fitted with Piezometer Tube & Scale 5.Piping : GI / PVC 6.Stop Watch : Electronic 7.Control Panel : With required electrical instrumentation The whole Set-up is well designed and arranged in a good quality painted structure.
Tubing, Rubber
XTEMOS ELEMENT
AJAX PRODUCTS TABS ALTERNATIVE
Fashion
Gas Tap, Economy
Description
Made of brass with superior chrome plating. Output nozzle having 6mm bore. Inlet 1/2 X 14. Flange diameter 46mm with two holes to fix on bench or any other surface with screws. To be fitted directly on fitting. Designed to operate at pressure up to 2 psi (0. 14kg/cm2). Suitable for use with coal gas, natural gas and L.P.G.Particulars
Gas Tap, One Way Gas Tap, Two Way Gas Tap, Three Way Gas Tap, Four Way
Disintegration Test Unit
Features
Digital timer with 1 second resolution. Accurate time out provided by microprocessor based time totalizer. Baskets move Up & Down as per IP/USP test specifications. Temperature Controlled by sensitive thermostats. Digital Tablet Disintegration Apparatus is designed for accurate estimation of disintegration time of tablets as per IP/USP standards. The instrument is designed to test to batches of six tablets, simultaneously. The unit consists of two beakers having capacity of 1000 cc each. In these beakers, suitable disintegration media can be taken. These can be temperature controlled using a in-built heater and a highly thermostat fitted inside the instrument. Microprocessor based time to talizer is provided for accurate time readout.Specifications
System :Digital Tablet Disintegration Apparatus. Up and Down Speed:30 rpm ± 2 rpm. Accuracy: 2% Resolution:1 sec. Operating Temp. Range:0 - 100°C Power:230V ± 10%, 50Hz.AC
Pulse Code Modulation/Demodulation
FEATURES:
• In-built sine wave generator • Test points to study different waveforms • In-built DC Power supplyTechnical Specifications:
• Sine wave Generator : Frequency : 1 KHz, Amplitude : 0 to 3Vpp • DC Voltage : -1.5 V to +1.5V • Clock Generator : Crystal based, 4.096MHz • Data rate : 64 kbps (for 8 KHz sampling rate)128kbps (for 16 KHz sampling rate) • ADC and DAC bits : 8 • Demodulator filter type : Butterworth low pass filter • Filter type : 6th • Filter cut-off frequency : 3.4 KHz • Mic Pre-amplifier : Transistor based • Compandingrange : -80dBm to +20dbm • Switched faults : 4 • Test points : 35 • Fuse : 30V, 100mV • DC Supply : ±5V, ±12V • System Bandwidth : 3.4 KHzXTEMOS ELEMENT
AJAX PRODUCTS TABS ARROWS PAGINATION
Mechanical Training Model
Description
Highly useful for demonstrating the most fundamental and frequently used mechanism. Very useful for engineering students. All the components are made of high degree of precision. These modules are assembled on transparent perspex sheets to facilitate teaching. Easy to assemble or disassemble.
Hydraulic Power Steering System Motorised
Hydraulic Power Steering System (Motorised) – Actual Working
The working of steering system is shown with the help of actual parts assembled on square iron pipe frame. All the necessary parts of steering system are shown in actual working form. This model helps the student to understand the working of the steering system very easily. It is specially made dissectible for demonstration purposes.
XTEMOS ELEMENT
AJAX PRODUCTS TABS WITH ICONS
5KVA IGBT Based Converter Inverter System
DC Motor Specification
• Power : 3HP • Armature voltage : 220V DC • Field voltage : 220V DC • Speed : 1500 RPM • Make : Benn • Double side shaft extensionSlip Ring Motor
• Type : 3phase slip ring induction motor. • Power : 2KW • Stator voltage : Three phase 415V AC, 4A • Rotor voltage : Three phase 210V AC, 6A • Speed : 1410 RPM • Make : BenndsPIC 30F4011 based PWM Controller
• Microchips’ dsPIC30F4011 16 bit digital signal controller operating at 20MIPS • On chip 48K Bytes flash program memory • On chip 1K Bytes data EEPROM • On chip 2K Bytes RAM • Four Compare/PWM output • Six PWM output for Motor control • One 3 channel Quadrature Encoder interface circuit/4 capture input • 9 Channels 10 bit ADC of 500Ksps conversion tune. • One RS232 Compatible serial port Opto isolated & terminated at 9 pin D male connector • 6 PWM outputs and two capture inputs and two compare outputs are terminated at 34pin FRC connector. • 4 Channels of DAC output & 5 channels of ADC inputs are terminated at 26 pin FRC connector • 16 x 2 alphanumeric LCD display
RNA Model on Stand
89V51 Development Board
Specification:
• High Performance P89V51RD2 device • On board ON/OFF switch and programmer / execution switch • 4x4 Matrix Keypad interface • 8-way DIP switch for digital logical input selection • 8 LEDs for digital output • One 16x2 Alphanumeric LCD display • 4x4 Matrix Keypad, On board 16x2 LCD • Real Time Clock (RTC) interface with four Functional keys • RS232 – UART interface with two status LEDs • All the 32 I/O lines are terminated via 4 FRC connectors • On board 0.5Kg Stepper motor with driver circuit • 2 nos of 12V relay for DC Motor • Software compatible for both C and Assembly language • 8 channel ADC with built in analog signals, internal & external data i/p, Temperature sensor, 2 nos of potentiometer for signal separation • On board DAC with buzzer
PLC Based Variable Frequency Drive Module
Specification
• PLC provided to control the variable frequency drive • PLC having Analog Input and Analog Output channels in range of (0-10)V DC • PLC having the digital I/Os in range of 24V DC • Communication cable (RS 232/Ethernet) will be provided communicate the PLC to PC • VF drive provided it operates at 230V AC supply • It provides the 3Φ AC output voltage • 3Φ AC Induction motor will provides. It operates at 415 AC, 3Φ, Frequency as 50Hz and rated 1500 rpm speed • PLC and VF drive mounted on the attractive printed panel trainer kit. • Variable pot meter, push button and connectors provided for experiment purposeXTEMOS ELEMENT
AJAX PRODUCTS TABS LOAD MORE PAGINATION
SILICA CRUCIBLE WITHOUT LID
PRODUCT DESCRIPTION
- Crucible is glazed inside and outside.
- Highly resistant to alkalis and hot temperatures
- 50ml capacity
- Outside diameter 55mm, 42mm height
- No lid includedSilica crucible is glazed inside and outside. Highly resistant to alkalis and hot temperature SIZES ARE: 15ML 25ML 50ML 80ML 100ML 150ML
SILICA CRUCIBLE TALL FORM Without Lid, Translucent
XTEMOS ELEMENT
AJAX PRODUCTS TABS CAROUSEL
Worm Sector Type Steering System
Worm & Sector Type Steering System – Actual Working
The working of steering system is shown with the help of actual parts assembled on square iron pipe frame. All the necessary parts of steering system are shown in actual working form. This model helps the student to understand the working of the steering system very easily. It is specially made dissectible for demonstration purposes.
Rheostat, Single Tube
Description
A layer of oxidized resistance wire is wound on a porcelain tube which is supported by end supports. A sliding contact and three 4 mm socket terminals are provided for use as a rheostat or as a potentiometer. Other ranges also available on request.| Ohms | Ampere | Tube length | |
|---|---|---|---|
| 23 | 2.3 | 150mm | |
| 10 | 3.3 | 150mm | |
| 22 | 2.8 | 200mm | |
| 24 | 3.3 | 250mm | |
| 28 | 4.2 | 400mm |
Trinocular Microscope
| Viewing Head | : | Trinocular Head Inclined at 45°, 360° Rotatable; 55-75mm interpupillary distance. Digital Camera or Digital Screen can be to the trinocular head. | |
| Eyepiece | : | Paired Wide Field 10x, WF 15x. | |
| Nosepiece | : | Quadruple Nosepiece. | |
| Achromatic Objectives | : | 4x, 10x, 40x (SL), 100x (SL, Oil Immersion). | |
| Stage | : | Stage is fitted with co-axial mechanical stage. | |
| Focusing | : | Coaxial coarse & fine focus knob. | |
| Condenser | : | Two lens abbe condenser NA 1.25 with iris diaphragm, filter holder and blue filter, movable by rack and pinion mechanism. | |
| Illumination | : | LED Illumination with adjustable intensity. |
LABORATORY AND MEDICAL MONOCULAR MICROSCOPE
PRODUCT DESCRIPTION:
Being a leading firm in this industry, we are deeply engaged in offering a high-quality range of MS 30 Medical Monocular Microscope.
Details:
- MS-30 Student Monocular Compound Microscope
- Viewing Body Monocular tube, Straight,
- Stand Monocular, frame inclines back to 90°
- Eyepiece eyepiece 10x
- Nosepiece Quadruple revolving Nosepiece
- ObjectivesSA series Achromatic objectives 10x/ NA 0.25 , 40x/ NA 0.65 (SL) , 100x/ NA 1.25 (SL, Oil)
- Stage Stage plate size 124 x 120mm with Mechanical stage for X and Y movement of slide up to 30 x 75mm with graduated scale and Vernier’s
- Focusing Separate coarse and fine focus controls. Coarse movement by Rack & Pinion and fine movement by Screw Lever Mechanism
- Condenser Sub-stage Iris diaphragm with moving up and down through rack and pinion, condenser NA 1.25 with Blue Filter
- Illumination System Plano concave reflector mirror mounted at the base
- Package Contents Thermocole Box, with operation manual, dust cover and cleaning cloth
