XTEMOS ELEMENT
AJAX PRODUCTS TABS
Pulley Blocks
Car Chassis Rear Wheel Drive Actual Cut Section Motorised
Car Chassis Rear Wheel Drive Actual Cut Section – Motorised
4 Stroke 4 Cylinder Petrol Engine With Clutch, Gear Box, Propeller Shaft, & Rear Axle Assembly With Differential Gear
The chassis of the four stroke four cylinder engine cut section model. The cut section model is constructed such that all the following systems can be demonstrated in working conditions.
ENGINE:
Maximum parts and accessories of an engine like cylinders, cylinder head, inlet and Exhaust manifolds, FIP, injectors, self-starter, alternator, water pump, radiator, etc., are sectioned to show the internal constructional details. The complete sectioned model is coupled with FHP 220/230V A.C single phase motor through a Reduction drive unit.TRANSMISSION SYSTEM:
This system consists of a Clutch and four speed gearbox assembly, the casing of which is suitably cut to demonstrate its operation. The gearbox is coupled to Differential gear box with propeller shaft and the different coupling used for this transmission can be demonstrated. The Differential gear box is also cut so as to clearly to demonstrate its complete operating principle. The gear shifting including the forward and reverse gear operation can be clearly shown. The speed variation and the rotation of the Differential gear box can be seen while gear shifting. By running the motor connected to the engine assembly the entire system with gear box, rear axle etc. can be demonstrated in running. FUEL SYSTEM: The Fuel tank is cut to expose the mounting of the level sensor and the position of Fuel section. The system is complete with mechanical Fuel pump. EXHAUST SYSTEM: It consists of Exhaust Manifold and silencer in cut section to explain internal construction. LUBRICATION SYSTEM: It consists of the engine Lubrication system along with the Lubrication oil pump is suitably sectioned. SUSPENSION SYSTEM: This will explain both the Hydraulic Suspension systems at the front and the leaf spring Suspension at the Rear. One of the hydraulic arrangements of Suspension mechanism is highlighted (with shock absorbers) and explained cut sectionally.BRAKING SYSTEM:
The Hydraulic or Air circuit Brakes. The movement of the Brake Shoes on operating the brake pedals can be seen in the area where the Brake drum is cut. The front and rear brakes will be operational. STEERING MECHANISM: The can be seen and included in the Steering wheel. Steering gear box and coupling of the same to the wheels will be shown by rotating the steering wheel, the operation of the steering system can be demonstrated. The entire system will be mounted on the chassis, and suitable mounting option with caster wheels will be provided for easy movability.
Newton Meters
XTEMOS ELEMENT
AJAX PRODUCTS TABS SIMPLE
Open Wind Tunnel Apparatus
Technical Description
A wind tunnel is the classic experiment system for aerodynamic flow experiments. The model being studied remains at rest while the flow medium is set in motion, and thus the desired flow around the model is generated. Open wind tunnel used to demonstrate and measure the aerodynamic properties of various models. For this purpose, air is drawn in from the environment and accelerated. The air flows around a model, such as an aerofoil, in a measuring section. The air is then decelerated in a diffuser and pumped back into the open by a fan. The carefully designed nozzle contour and a flow straightener ensure a uniform velocity distribution with little turbulence in the closed measuring section. The flow cross section of the measuring section is square. The built-in axial fan with guide vane and a variable-speed drive is characterised by an energy-efficient operation at high efficiency. Air velocities of up to 28m/s can be reached in this open wind tunnel. The trainer is equipped with an electronic two-component force sensor.Lift and drag are detected and displayed digitally. The air velocity in the measuring section is displayed on the inclined tube manometer. The tube manometers is recommended for measuring the pressure curves in drag bodies. Extensive accessories allow a variety of experiments, for example lift measurements, pressure distributions, boundary layer analysis or visualisation of streamlines. The well-structured instructional material sets out the fundamentals and provides a step-by-step guide through the experiments.Learning Objectives & Experiments
– Determine drag and lift coefficients for different models – Pressure distribution when flowing around drag bodies – Boundary layer analysis – Investigation of flutter – Wake measurementFeatures
* Open wind tunnel for a variety of aerodynamic experiments * Homogeneous flow through the flow straightener and special nozzle contour * Transparent measuring section
Tuning Forks Set
Arthropoda
Description
All Charts are made on PVC rexine , hand drawn, waterproof, in fast multi colors with a black background. Each chart is provided with rollers to hang on wall. Size 75×100 cm. Food Grain Pests Housefly Life History Mosquito Life History showing comparison of Culex & Anopheles Butterfly Life History Honey Bee Life History Silkworm Life History Grasshopper Life History Cockroach External Character & M.P. Cockroach L.H. Cockroach Digestive system Cockroach Respiratory system Cockroach Circulatory system Cockroach Nervous system Cockroach Reproductive system Prawn Internal Anatomy Prawn External Anatomy Prawn Reproductive system Prawn Digestive system Prawn Excretory system Prawn Nervous system Prawn Circulatory system Scorpion External Character, Dorsal & Ventral View
Optical Bench, Junior
Description
On wooden base, with 1.5 meter scale, with six sliding bases. Each siding base is with an index mark, a brass pillar and locking screw, with following accessories: 1. One lamp house with 230 V lamp. 2. One object screen, metal, white. 3. One lens holder for 38 mm diameter Lenses. 4. One receiving screen, metal, white, with slot for squared paper on reverse. 5. One object needle, mounted in brass rod. 6. One plane mirror in metal frame. Each of these accessories is mounted on a 6 mm brass rod which fits into the pillars and is adjustable for height.XTEMOS ELEMENT
AJAX PRODUCTS TABS ALTERNATIVE
Fashion
Fly Wheel
Low Voltage Coils, For Demountable Transformer
Corcyra Cage
Solar Wind 3Φ, 2KW Smart Grid
This consists of 2 Microgrids of 2000W &1000W of power generation connected to a main Power Grid with all the components needed to convert a traditional Grid to a Smart so that many experiments can be conducted on this “Smart Grid”. A 3Φ 3KW isolation transformer with power input from utility grid will act as main grid to which 2 Microgrid will be connected through synchronizing panel. Optionally a commercial 3Φ, 2.5KVA Grid Commercial Solar Power Inverter can be added to this experimental setup. By adding 3Φ, 2.5KVA commercial solar inverter, when the experimental setup is not used by student, it may be used to generate power.
This Advanced Smart Grid Experimental Setup Consists of
• 2 Micro Grids, each 1000W of power generation using Solar, Wind or Hybrid • An Isolation Transformer Coupled to the utility Grid, acts as Main Grid to this Setup • Various other Power Sources • Commercial 3Φ 5KVA Grid Connected Inverter (Optional) • Optional Components for the Smart Grid Setup • DSP /FPGA Controller for PE, SG, PS Applications • Other Add ons • Components for Building 10/25KW Smart Grid Power Generation • IoT Based Data Acquisition.Solar Wind Grid Connected 3Φ, 2KW Smart Micro Grid
• Main Frame • 1KW Solar PV Module with Stand • Wind Turbine • DC-DC Boost Converter • 120V Battery Bank - 12V x 100AH x 10 Nos • 2KW Bi-Directional DC-DC Buck-Boost Converter for Charging battery • 2KW 3Φ Inverters • DSP/FPGA Controller • Microcontroller based Protection Relays • Smart Energy Meter • Synchronizing Panel • Three Phase RL Load 2KW • PLC with SCADA Software • 14 Channel PC based Power Quality Analyzer (Optional)XTEMOS ELEMENT
AJAX PRODUCTS TABS ARROWS PAGINATION
Calorimeter Stirrer, Aluminium
Potentiometer
L Shaped Spreader
We are a prominent Exporter & Trader of L Shaped Spreader.
The L Shaped Spreader is sterile & smooth and enables even spreading of liquid samples across the surface of a jar plate without grouping & cutting the medium.
Avail the L Shaped Spreader from us at nominal market prices.
Material : Polypropylene
| Particulars | Pack (Pcs) | |
|---|---|---|
| L Shaped Spreader | 100 | |
| Micro Pestle (for 0.5 and 1.5 ml MCT) | 12 | |
| Micro Pestle (for 1.5 ml MCT) | 12 |
Carboys
Carboys, made of polypropylene, are much lighter than glass.
These autoclavable, dependable & durable Carboys are provided with wide handles making it convenient while carrying or pouring purposes.
We also offer carboy with stopcock for the esteemed clients.
Material : Polypropylene
| Particulars | Pack (Pcs) | |
|---|---|---|
| Carboy 10 ltrs. | 1 | |
| Carboy 20 ltrs. | 1 | |
| Carboy With Stop Cock 10 ltrs. | 1 | |
| Carboy With Stop Cock 20 ltrs. | 1 |
XTEMOS ELEMENT
AJAX PRODUCTS TABS WITH ICONS
Aluminium Tripod Stand Dual Lock
Description
We are supply and Export of aluminum tripod stands that are procured from the trustworthy sources, who make these using high quality raw material such as brass and aluminum. These products are also available in a powder coated finish and are especially developed for providing maximum stability and strength. Moreover, all our products are available in various sizes, shapes and designs to fulfill the diverse needs of our clients.
Hot Air Oven
| Specification | : | Hot air oven, 2 shelves |
|---|---|---|
| Technical Specifications | : | |
| Inside Body | : | Stainless Steel |
| Out Side Body | : | MS Powder coated with stove enamel paint. (SS body also available) |
| Number of Selves | : | 2 Adjustable Perforated Selves. |
| Body Structure | : | Double Walled structure filled with glass wool insulation |
| Number of Heaters | : | 2 x 1000 Watts |
| Heater Quality | : | High Quality Chrome Heater insulated with ceramic beads |
| Air Circulation | : | By Air Circulating Fan to ensure even temperature distribution. |
| Ventilation | : | Ventilation port with adjustable Opening. |
| Temperature Control | : | By Digital Temperature indicator and Controller |
| Temperature Display | : | Digital Temp. display |
| Range of Temperature | : | Ambient to 250ºC |
| Accuracy | : | 0.10C |
| Least Count | : | 1.0C |
| Power | : | 220 Volt AC 50 Hz. Single Phase |
| Sizes available are | : | 12" x 12" x 12" (28 Ltr.)14" x 14" x 14" (45 Ltr.)18" x 18" x 18" (95 Ltr.)24" x 24" x 24" (224 Ltr.) |
XTEMOS ELEMENT
AJAX PRODUCTS TABS LOAD MORE PAGINATION
SILICA CRUCIBLE WITHOUT LID
PRODUCT DESCRIPTION
- Crucible is glazed inside and outside.
- Highly resistant to alkalis and hot temperatures
- 50ml capacity
- Outside diameter 55mm, 42mm height
- No lid includedSilica crucible is glazed inside and outside. Highly resistant to alkalis and hot temperature SIZES ARE: 15ML 25ML 50ML 80ML 100ML 150ML
SILICA CRUCIBLE TALL FORM Without Lid, Translucent
XTEMOS ELEMENT
AJAX PRODUCTS TABS CAROUSEL
Long Stem Funnel
We offer Long Stem Funnel which is made in accordance to the international standards.
These Long Stem Funnel have smooth walls, 60" cone angle and external ribs to prevent air lock.
Moulded in Polypropylene, these clear funnels can also be steam autoclaved.
Material : Polypropylene
| Particulars | Pack (Pcs) | |
|---|---|---|
| Funnel- Long Stem 100 mm | 36 | |
| Funnel- Long Stem 150 mm | 12 | |
| Industrial Funnel 200 mm | 12 | |
| Industrial Funnel 250 mm | 6 |
Slide Storage Rack
We are engaged in providing Slide Storage Rack can hold 100 slides which are recognizable through the numeric indexing.
Spacing between the slots provides adequate backward & forward movement of slides for convenient recognition.
Made of ABS, the transparent cover provides excellent view of the slides stored inside.
Material : Acrylonitrile Butadiene Styrene
| Particulars | Pack (Pcs) | |
|---|---|---|
| Slide Storage Rack - 100 Slides | 6 | |
| Float Rack | 12 |
Three Phase Cyclo Converter
This module is designed for three phase half wave-step down cycloconverter. It consists of 18 Synchronized firing pulses, 18 SCRs, Relevant power supply and circuitry for frequency divisions.
Specification
• Eightin nos. SCR with RC snubber protection is provided for 3phase • cycloconverter power circuit (each phase consist of 6 SCRs) Rated at 1200V@25Amps. • Three nos. center tapped inductor (0%.50%, 100%) is provided for power circuit. • Eightin nos. Isolated gate pulses for SCR power circuit. • One potentiometer is provided to vary the frequency. • One potentiometer is provided to vary the output voltage. • MCB protection. • Housed in sleek screen printer cabinet. • Provision for V/F control Power Supply. • Input 440V ± 10%, 50HZ three phase AC supply. • ± 15V DC, 9V, 9V, 9V AC (3phase) for the firing circuits. • 24-0-24V 3phase input for power circuit.
Planck’s Constant
Modern LEDs (light emitting diodes) cover the range from deep blue (440 nm) to infra-red (940 nm). By monitoring the voltage at which each LED just begins to emit light a graph of energy input as a function of light emitted frequency can be plotted and an approximate value of Planck’s constant deduced. Complete with viewing tube but without power supply.
