XTEMOS ELEMENT
AJAX PRODUCTS TABS
Refrigeration Test Rig
Features
• 5 Nos of thermocouples are provided to measure the temperature at different points. • One multi channel temperature indicator is provided to display the temperature • One capillary tube and one thermo expansion valve is provided to check the performance separately. • Compressor supplies refrigerant through evaporator to find out cooling effect • 4 Nos. of Pressure Gauges are provided to measure the pressure at various point • One Energy meter is proivded to measure the overall power consumption • One voltmeter is provided to display the voltage. • One ammeter is provided to display the current.Specification
• Compressor :Hermatic • Capacity : 1/4 Ton • Supply : 230 V AC / 50 Hz • Condensor : 12 Coil • Evaporator : 15 Liter Capacity • Refrigerant : R134A
Pressure Measurement Trainer
This module consists of a (0-100) psi pressure transducer of strain gauge type fixed in a pressure tank, one manually operated pump to develop pressure, pressure gauge and 3½ digital indicator to display the pressure.
Specification
• One metal pressure tank fitted with strain gauge type pressure cell. • A ball valve fitted in a pressure tank to release the pressure. • Bourden type pressure gauge provided in the tank to indicate pressure. • One manually operated foot pump to generate a pressure of the tank. • Signal conditioner for pressure cell output (0-5V) • Provision for offset/span adjustment. • A 3½ digit digital display indicator to indicate the pressure inside the tank
Refrigeration Trainer Domestic Type
The unit enables students to study the various parameters affecting the performance of a domestic refrigerator. It consists of refrigeration cycle of domestic refrigerator, it consists a hermetically sealed compressor, air-cooled condenser, capillary tube and a natural convection type evaporator. The evaporator is fitted with a small heater to simulate different load conditions various measurements are provided so that power consumption, COP, theoretical and actual refrigerating effects refrigerant flow rate and effect of door opening on power consumption can be studied and also students can visualize automatic operation of unit using a thermostat.
SPECIFICATIONS:
1.Compressor – Hermetically sealed, Kirioskar make having capacity of approx. 1/25 ton of refrigeration. 2.Air – cooled condenser with natural convection airflow. 3.Capillary tube of matched length as expansion device. 4.Evaporator coil with an electric heater inside and adequate glass wool insulation on all side. 5.Measurement a)Energymeter Tore compressor input power measurement. b)Pressure gauge for condensing and evaporating pressure. c)Flow meter for liquid refrigerant flow d)Digital Temperature indicator for measurement of temperature 6.safety & Controls a)High & low pressure cutout. b)Thermostat. c)Necessary Switches. A technical manual accompanies the unit. Also, the unit is provided with an attractive and rust proof powder coating.SERVICES REQUIRED:
1.Floor space of 2m x 1m. 2.230V AC stabilized supply with earthing connectionXTEMOS ELEMENT
AJAX PRODUCTS TABS SIMPLE
CNC Mill Trainer
CONTROLLER:
SIEMENS 802D Main Spindle Drive : D.C. Thyristor Drive, Inbuilt Safety, 1.5 HP X, Y and Z Drives : SIEMENS Servo Motors and Drives Input to Stepper : Optically lsolated Motor Drive TTL compatible Interpolation : Linear, Circular parabolic Interpolation, Slot / Pocket Milling Code Used : G, M, S, T, F, I, K, M, F, Cycles : Circular Interpolation, Mirror, Pocket Milling Cycle Pocket & Helical Milling : Provided with Std CodesTABLE:
Length x Width : 450 x 175 (approx.) Clamping Area : 350 x 175 (approx.) T Slots : 10mm slot widthMACHINE DETAILS:
Resolution : 5 micron Tool Change : Automatic, 8 station Rapid Travel : 5000mm/min Weight in kg : 750kg Dimension in mm : 850 x 850 x 1550 mm Automatic Lubrication : Provided Repeatability : 10 micronSPINDLE:
Spindle Speed : Continuous Variable Spindle power : 1.5 HP Inside Taper : ISO 30 Speed Range : 100 to 4000 RPMAXIS TRAVEL
Longitudinal Traverse : 250mm Cross Traverse : 175mm Vertical Traverse : 250mm
Condensers , Liebig, Drip Tip Interchangeable Inner & Outer Joint
| Socket | Cone | Effective Length mm | |
|---|---|---|---|
| 14/23 | 14/23 | 150 | |
| 19/26 | 19/26 | 200 | |
| 24/29 | 24/29 | 200 | |
| 19/26 | 19/26 | 300 | |
| 24/29 | 24/29 | 300 | |
| 19/26 | 19/26 | 350 | |
| 24/29 | 24/29 | 350 | |
| 19/26 | 19/26 | 400 | |
| 24/29 | 24/29 | 400 | |
| 24/29 | 24/29 | 500 | |
| 24/29 | 24/29 | 600 | |
| 24/29 | 24/29 | 750 | |
| 34/35 | 34/35 | 500 | |
| 34/35 | 34/35 | 600 | |
| 34/35 | 34/35 | 750 | |
| 34/35 | 34/35 | 900 | |
| - | 19/26 | 300 | |
| - | 24/29 | 350 | |
| - | 34/35 | 250 | |
| 29/32 | 29/32 | 250 | |
| 29/32 | 29/32 | 400 |
XTEMOS ELEMENT
AJAX PRODUCTS TABS ALTERNATIVE
Fashion
Leopold Maneuvers Simulator
Description
One piece fetal baby with palpable fontanelles, spine, shoulders, elbows, and knees Fetal baby may be placed in normal, breech, or transverse position Fetal baby cradled between two “cushions” Cushions may be inflated independently of the other; inflation of the lower cushion raises the fetus to desired position; inflation of the upper cushion creates a firm abdomen as in the ninth month of pregnancy The Palpation Module is designed to be used with the Advanced Childbirth Simulator.
Brush, Beaker
Survey Compass
Description
• Compass survey is a method of surveying by taking bearings and linear distances to produce plan. • Bearing is measured using prismatic compass, while the linear distance is measured using measuring tape. • Bearing in compass surveying means angle is made by chain line or survey line by referring it to magnetic meridian or magnetic north.
XTEMOS ELEMENT
AJAX PRODUCTS TABS ARROWS PAGINATION
Instrument Tray
Acquire from us comprehensive range of Instrument Tray which is well reckoned for its quality.
This Instrument Tray has cover which fits into groove of trays to minimize spillage of material.
Smaller size can be used to sterilize small instruments whereas the larger size allows pipettes to be fully immersed in disinfectant prior to sterilizing.
Material : Polypropylene
| Particulars | Pack (Pcs) | |
|---|---|---|
| Instrument Tray 220 x 150 x 70 mm | 2 | |
| Instrument Tray 450 x 150 x 70 mm | 2 |
Calorimeter copper
Heat Transfer In Aagitated Vessel
The unit consists of a vessel with class wool insulation ail around. A helical coil made of copper is fixed inside the vessel. A motorized agitator is fixed at the center of the coil. The vessel is provided with an electric heater and a controller is also provided for vessel. Heater heats water in the jacket while cold water is circulated through coll. Temperature of circulated water and water In vessel Is measured and thus heat transfer coefficient at various agitator speeds can be determined.
SPECIFICATIONS:
1.Vessel approx. 20 lit. capacity, provided with glass wool insulation all around and electric heater at the bottom. 2.Agitator 150 mm dia, with 1/8 HP motor to drive the agitator. 3.Helical coil – 200 dia, 8 turns, made of 3/8″ dia. copper tube. 4.Controllers for heater and agitator motor. 5.Temp. Indicator for vessel water temperature and circulated water inlet and outlet.SERVICES REQUIRED:
1.Single phase 230V, 15 A stabilized supply. 2.Water flow at the rate of 4 to 5 lit. per min. 3.Suitable drain arrangement for water. 4.Floor area -1.5 mtr. X 1 mtr. X 1 mir height.XTEMOS ELEMENT
AJAX PRODUCTS TABS WITH ICONS
Water Still with Metal Heater
Specifications
Water stills are carefully designed to produce high purity pyrogen free distilled water. The water still made from 3.3 exp. borosilicate glass comprises of horizontal type boiler, condenser, constant level device, silica sheathed heater, along with stand and clamps.Features
Borosilicate condenser and boiler are with a removable silica sheathed heater and screw threaded connectors for ease of Cleaning. Distillate temperature is approx. between 25° to 45°C which is ensured by an efficient condenser. The stand is powder coated for rust free operation and lustrous appearance. The unit automatically switches off if water level in the boiler falls below heater. Cooling water from the condenser is re-circulated into the boiling chamber, hence saving energy. Drain nozzle/Teflon Stop Cork is provided for easy cleaning and maintenance. Electrical Power: 220/240 V, 50/60Hz, Single Phase Supply.
Fuel Supply System Diesel CRDI Type
Fuel Supply System Diesel CRDI Type (Actual Working Model) Common Rail Direct Injection.
This is an actual working model of fuel supply system of a CRDI diesel engine. The parts details is as under ::
This is an actual working model of fuel supply system of a MPFI petrol engine. The parts details is as under ::
1. Fuel Tank
2. Fuel Filter
3. Motorised Fuel Pump
4. Pressure Gauge
5. Fuel Rail
6. Fuel Injectors
7. ECU
8. Power Supply
9. Fuel Gauge & Control Panel
This model helps the student to understand about the parts & working of CRDI system. It is specially designed for demonstration purposes. The model will be supplied with key card & very interesting literature regarding working.
Dicot & Monocot Root
Thin Cylinder Apparatus
A heavy bench top unit for studying the stress and strain in a thin walled cylinder under internal pressure. A thin walled cylinder is mounted between two support blocks. Internal pistons and seals create oil sealing. A handwheel at one end of the apparatus enables the cylinder end conditions to be adjusted to either open or closed. The internal pressure is adjusted by means of a hydraulic hand pump on the apparatus. An analogue pressure gauge displays the internal pressure whilst a pressure transducer gives feedback to the Data Acquisition Interface and Software supplied. Strain gauges are arranged on the external surface of the cylinder to measure the radial and circumferential surface strain. The strain gauges are at various angles.
XTEMOS ELEMENT
AJAX PRODUCTS TABS LOAD MORE PAGINATION
SILICA CRUCIBLE WITHOUT LID
PRODUCT DESCRIPTION
- Crucible is glazed inside and outside.
- Highly resistant to alkalis and hot temperatures
- 50ml capacity
- Outside diameter 55mm, 42mm height
- No lid includedSilica crucible is glazed inside and outside. Highly resistant to alkalis and hot temperature SIZES ARE: 15ML 25ML 50ML 80ML 100ML 150ML
SILICA CRUCIBLE TALL FORM Without Lid, Translucent
XTEMOS ELEMENT
AJAX PRODUCTS TABS CAROUSEL
Lens, Double Convex, Spherical
Description
Clear glass, ground edges
| Focal length | Power | Add To Enquiry |
|---|---|---|
| 25 mm | 100 mm | +10D |
| 25 mm | 150 mm | +6.6D |
| 38 mm | 50 mm | +20D |
| 38 mm | 100 mm | +10D |
| 38 mm | 150 mm | +6.6D |
| 38 mm | 200 mm | +5D |
| 38 mm | 250 mm | +4D |
| 38 mm | 300 mm | +3.3D |
| 38 mm | 500 mm | +2D |
| 38 mm | 1000 mm | +1D |
| 50 mm | 50 mm | +20D |
| 50 mm | 100 mm | +10D |
| 50 mm | 150 mm | +6.6D |
| 50 mm | 200 mm | +5D |
| 50 mm | 250 mm | +4D |
| 50 mm | 300 mm | +3.3D |
| 50 mm | 500 mm | +2D |
| 50 mm | 1000 mm | +1D |
| 60 mm | 100 mm | +10D |
| 60 mm | 200 mm | +5D |
| 60 mm | 300 mm | +3.3D |
Digital Coductivity Meter
| Usage | Industrial, Laboratory | |
| Material | MS | |
| Color | White |
Features
Highly Stable and Accurate Cell Constant Adjustment Facility Available in Lab & Field models Temperature Coefficient Correction facility| Display | 3 1/2 Digit LED | 3 1/2 Digit LCD |
|---|---|---|
| Range | 5 Ranges 0 - 1000 Mohs/cm | 2 Ranges 2 & Mohs/cm |
| Temperature Compensation | Manual 0-50oC | - |
| Cell Constrant Adjustment | Adjustable | Pre Adjustable |
| Conductivity Cell | Platinum DIP | Platinum DIP |
| Measuring Frequency | 1000 Hz | 1000 Hz |
| Accuracy | 1% FSI | 1% FSI |
| Power | 230v 10% | 1 x 9V Battery |
| Dimensions | 76 x 275 x 175 mm | 85 x 28 x 165 mm |
| Weight | 2 kg. (Approx.) | 0.8 kg. (Approx.) |
| Accessories | Conductivity Cell, Operation Manual, Dust Cover. | |
