XTEMOS ELEMENT
AJAX PRODUCTS TABS
RF Signal Source with Detector
Specification
• 25 to 6000MHz RF synthesized signal generator. • Programmable attenuator 5, 10, 20, 30dBm up to 1.5GHz. • 40 x 2 LCD Display to display the frequency of the RF signal and RF signal level. • Output level : 0dBm +/2dB upto 1GHz, -5dBm, +/-2dB upto 3GHz, -10dBm, +/-3dB upto 6GHz. • Output impedance : 50 ohm. • One RF Power detector provided for 50 to 1000MHz frequency range and this output is measured • by an ADC and display on the LCD display. • 6 Keys keypad provided to select the desired frequency, attenuation level, Sweep mode. • Step size : 1MHz. • Connectors: - 2 Nos. of 'N' type connector for RF out and RF in. - One "BNC" type connector for RF detector output.
PAM-PPM-PWM Modulation and Demodulation Trainer
PAM- PPM- PWM is the basic pulse modulation techniques. This trainer provides complete setup to the students for performing Experiments on these techniques. They can study Sampling, Pulse Modulation &Signal reconstruction process. Separate circuits are provided for each Techniques.
FEATURES:
• PAM- PPM- PWM Modulation and Demodulation Techniques,using Natural and Flat - top Sampling. • Natural Sample, Sample and Hold and Flat-top outputs. • Selectable 2 different sampling pulse frequencies on board. • On board Sine wave generators. • Voice communication using dynamic microphone and speaker • On board Filters and Amplifier • Functional blocks indicated on board schematic • Input- Output and Test points provided on board. • Built in DC Power Supply • Fully documented operating ManualTECHNICAL SPECIFICATION:
• Crystal Frequency : 6.14MHz • Sampling Frequency : 16 KHz, 32 KHz • Sine wave Generator : 1 KHz &500Hz, Amplitude (0-5)V, Tolerance +5% • Low Pass Filter : 4 Order BW Filter • Cut off frequency : 3.4 KHz • Voice Communication : Voice Link using dynamic mic& speaker • AC Amplifier : With Adjustable Gain control • Microphone type : Dynamic, 600 Ohm. • Audio Pre-amplifier : Op-amp based • Power amplifier : 1W Mono • Interconnections : BS2 Connector. • Power : 230V, 50Hz
Disintegrator
Description
Highly polished hooper dia 2". 16x25mm Completed with suitable motor to work on 220V AC 50Hz single phase. Fitted with 4 steel hammers fixed to a disc of dia. 1½" through which passes a shaft being revolved at the speed of approximately 3000 RPM. Hammers are enclosed in a drum. The lower portion can be fitted with different mesh screens (sieves)-coarse, medium or fine supplied with the equipment.
Vernier Calipers Precision
XTEMOS ELEMENT
AJAX PRODUCTS TABS SIMPLE
Model of Astronomical Telescope
Dissecting Set, Simple
Measuring Jugs
The Measuring Jugs, moulded in Polypropylene are clear, autoclavable and have good chemical resistance.
The Measuring Jugs are provided with a handle for easy & convenient lifting and have raise graduations for easy reading.
Adding to the existing range of Jugs, these short form transparent jugs, made of polypropylene are autoclavable and have non-drip spout.
These jugs have raised graduations, provide excellent contact clarity, & are provided with excellent thumb grip on handle.
Material : Polypropylene
| Particulars | Pack (Pcs) | |
|---|---|---|
| Measuring Jug 250 ml | 12 | |
| Measuring Jug 500 ml | 12 | |
| Measuring Jug 1000 ml | 6 | |
| Measuring Jug 2000 ml | 6 | |
| Measuring Jug (Euro Design) - 500 ml | 12 | |
| Measuring Jug (Euro Design) -1000 ml | 6 | |
| Measuring Jug (Euro Design) - 2000 ml | 6 | |
| Measuring Jug (Euro Design) - 3000 ml | 6 | |
| Measuring Jug (Euro Design) - 5000 ml | 4 | |
| Measuring Jug (Printed Graduation) - 100 ml | 12 | |
| Measuring Jug (Printed Graduation) - 250 ml | 12 | |
| Measuring Jug (Printed Graduation) - 500 ml | 12 | |
| Measuring Jug (Printed Graduation) - 1000 ml | 6 | |
| Measuring Jug (Printed Graduation) - 2000 ml | 6 | |
| Measuring Jug (Printed Graduation) - 5000 ml | 4 |
Arthropoda
Description
All Charts are made on PVC rexine , hand drawn, waterproof, in fast multi colors with a black background. Each chart is provided with rollers to hang on wall. Size 75×100 cm. Food Grain Pests Housefly Life History Mosquito Life History showing comparison of Culex & Anopheles Butterfly Life History Honey Bee Life History Silkworm Life History Grasshopper Life History Cockroach External Character & M.P. Cockroach L.H. Cockroach Digestive system Cockroach Respiratory system Cockroach Circulatory system Cockroach Nervous system Cockroach Reproductive system Prawn Internal Anatomy Prawn External Anatomy Prawn Reproductive system Prawn Digestive system Prawn Excretory system Prawn Nervous system Prawn Circulatory system Scorpion External Character, Dorsal & Ventral ViewXTEMOS ELEMENT
AJAX PRODUCTS TABS ALTERNATIVE
Fashion
Laboratory Spatula
Acquire from us high quality Laboratory Spatula at affordable price range.
Moulded in Polypropylene, Spatula consists of a spoon on one side while the other end is a flat construction with a knife edge.
This is helpful in breaking up crystals of different salts while the spoon is used to draw salts from the containers.
| Particulars | Pack (Pcs) | |
|---|---|---|
| Spatula 150 mm | 12 | |
| Spatula 200 mm | 12 |
Hand & Table Microtome
The Hand & Table Microtome is used to cut thin sections of Microscopic materials, such as specimen parts of plants and animals.
It is Considered as the basic form of a microtome permitting microtomic cuts by hand in a quick and accurate way.
The microtome is suitable for practical courses in microscopy, for field work during excursions, for school education and for a serious amateur of biology.
Urine Container
We offer best quality Urine Container s which can be used for collecting a wide range of samples of sputum, urine etc.
Moulded in polypropylene these containers are excellently leak proof.
These Urine Containers are manufactured from best quality raw material and are durable in nature.
Material : Polypropylene
| Particulars | Pack (Pcs) | |
|---|---|---|
| Urine Container 30 ml | 100 | |
| Urine Container 60 ml | 100 |
Earth, Neutral And Live Board Demonstration
Description
This apparatus is an effective demonstration of how the earth wire and fuse act together to protect both the user and the appliance. When the appliance is connected correctly and the LEDs in the appliance will illuminate to show the appliance is working. A fault is then demonstrated by swapping the live wire from inside the appliance to the case to show either the fuse melts (protecting the user and appliance) or in the case of no earth wire, the LEDs illuminate to indicate the passage of current through the person to ground. The fuse is easily visible and can be seen to ‘blow’ when a fault occurs.The unit is supplied with 10 m of fuse wire and full instructions. A 12 V DC power supply is required. Connections are made via 4 mm shrouded sockets.XTEMOS ELEMENT
AJAX PRODUCTS TABS ARROWS PAGINATION
BURETTE CLAMP
Copper Calorimeter, with wooden box
Refrigeration Trainer General Cycle Type
The unit consists of vapor compression refrigeration cycle provided with components normally used in refrigeration system so that student can get familiar with the components. Various measurement provided enable students to estimate the performance of the system.
SPECIFICATIONS:
1.Compressor- Hermetically sealed compressor, having capacity of 0.3 T. 2.Expansion Devices a) Thermostatic Expansion Valve b) Capillary tube. 3.Evaporator coil. 4.Controls: a) Services Valve b) Solenoid Valve c) Filter-Drier for refrigerant d) High/Low pressure cutout e) Thermostat. 5.Measurements: a) Thermometers (mercury in glass) – 4 Nos. b) Pressure gauges for condensing and evaporating pressure. c) Energymeter for compressor d) Voltmeter and Ammeter for compressor. e) Rotameter for liquid refrigerant flow measurement. A technical manual is accompanies the unit.SERVICES REQUIRED:
1.Floor surface area – 1m x 2m x 2m height. 2.220V, I5Amp, Single Phase Stabilized power supply
XTEMOS ELEMENT
AJAX PRODUCTS TABS WITH ICONS
Autoclave, Radial Locking
Specification
Double wall chamber Autoclave. The inner chamber and outer wall made of stainless steel, ring made of stainless steel/ mild steel. The lid is made of stainless steel tightened by radial arms through a steering wheel made of chrome plated mild steel. The instrument is absolutely leak proof. Equipped with pressure gauze, safety valve, double safety valve, steam release valve, rubber gasket, inner container, S.S bucket and mild steel legs for Autoclave. The Autoclave can hold the in between 5psi to 20 psi. Autoclave, Vertical, Double Walled, Radial Locking.| Capacity (Lt.) | Size | |
|---|---|---|
| 23 litres | (10” x 18”) | |
| 40 litres | (12” x 22”) | |
| 52 litres | (14” x 22”) | |
| 60 litres | (14” x 25”) | |
| 75 litres | (16” x 24”) | |
| 95 litres | (18” x 24”) | |
| 180 litres | (22” x 30”) |
Microcontroller Based Differential Relay
This test set-up consists of a. Microcontroller based differential relay. b. 300VA transformer set-up
Specification
• One PIC Microcontroller used as processor to read all current, (PY, SY) & activation of relay function • One LCD to indicate, - Set value, All currents - Set time, DMT/IDMT type - Relay tripping time. - Biased/Unbiased type status • Four numbers of key used - To select IDMT/DMT type or biased un-biased type - Set current value adjustment - Set time adjustment - Reset function • Six 5A CT used to sense primary and secondary current. • One 12V TPTT auxiliary relay used for contactor operation. • Specification: - Current input : 0-5Amp - Voltage input : 0-230V - Number of contact : Three number No contact @ 220V, 10Amp rating. - Auxiliary supply : 230VAC, 50Hz • PC interfacing facility power ON/OFF switch with indicator. • Make : VI MICRO • Model : VPL - 83A
Venturimeter Orificemeter Calibration Set Up
DESCRIPTION:-
The apparatus consists of two pipelines emerging out from a common manifold. One pipeline contain a Venturimeter, second contains an Orifice. The pressure tapings from the Venturimeter and Orificemeter are taken to differential manometer to measure pressure difference. The Venturimeter and Orificemeter are connected in parallel and anyone of them can be put in operation by operating valves provided at the downstream. These valves can also regulate the flow. Present Set-up is self contained water re-circulating unit, provided with a sump tank and a centrifugal pump. Flow control valve and by-pass valve are fitted in water line to conduct the experiment on different floe rate. Flow rate of water is measured with the help of measured with the help of measuring tank and stop watch.EXPERIMENTS:-
Ø To determine the Co-efficient of discharged through Venturimeter and Orificemeter Ø To measure discharge through Venturimeter and Orificemeter as flow meters.UTILITIES: –
Ø Water Supply & Drain Ø Electricity Supply: Single Phase, 220 VAC, 0.5 kWTECHNICAL SPECIFICATIONS: –
Ø Venturimeter : Material Clear Acrylic, Compatible to 1” Dia pipe Ø Orificemeter : Material Clear Acrylic, Compatible to 1” Dia. Pipe Ø Water Circulation : FHP Pump, Crompton / Sharp make Ø Flow Measurement : Using Measuring Tank, Capacity 25 Ltrs. Ø Sump Tank : Capacity 50 Ltrs. Ø Stop Watch : Electronic Ø Control Panel : On / Off Switch, Mains Indicator etc. Ø Tanks will be made of Stainless Steel Ø The whole Set-up is well designed and arranged in a good quality painted Structure
Interference Undercutting
The board shows the demonstration of this phenomenon of Interference and Undercutting. When we rotate the teeth in anticlockwise direction, as the teeth is undercut is gives us a smooth working. When we give a rotation in clockwise direction, we can observe that the rack tip will be resisted by the tooth flank thus giving interference.
XTEMOS ELEMENT
AJAX PRODUCTS TABS LOAD MORE PAGINATION
SILICA CRUCIBLE WITHOUT LID
PRODUCT DESCRIPTION
- Crucible is glazed inside and outside.
- Highly resistant to alkalis and hot temperatures
- 50ml capacity
- Outside diameter 55mm, 42mm height
- No lid includedSilica crucible is glazed inside and outside. Highly resistant to alkalis and hot temperature SIZES ARE: 15ML 25ML 50ML 80ML 100ML 150ML
SILICA CRUCIBLE TALL FORM Without Lid, Translucent
XTEMOS ELEMENT
AJAX PRODUCTS TABS CAROUSEL
Compound Microscope (Student Microscope)
Specification
Elegant body, practical design and coated lenses. Fixed square stage 120mm x 120 mm with optional mechanical stage or slide clips. Focusing by coarse & fine adjustment knobs. Illumination by plano concave mirror reflector or optional LED light. Eye Piece 10x & 15x Objective 4x, 10x , 40x/45x 100x oil immersion is optional. Available in Styrofoam pack for safe & easy transport. Wooden Box is optional.
Kidney Section, Nephrons , Blood Vessels And Renal Corpuscle
Description
Set of three models on one board. Kidney section, 3 times full size. Nephrons and blood vessels 120 times full size showing a section through renal cortex and medulla. Malpighian corpuscle of kidney,700 times enlarged showing an opened Malpighian corpuscle with glamerules and Bowman’s capsule. On base with key card.
Gynecological Examination Model
Description
Gynecological Simulator is ideal for all aspects of gynecological education, training and competency evaluation, including the bimanual exam, speculum exam, and cytology sampling. Students will appreciate the unprecedented realism of its internal and external features, while instructors will love the interchangeable components that make up its unique modular system. This simulator allows you the flexibility of customizing your scenarios with use of included makeup, blood, and thickener. Additional specialized modules are also available (STD, post-menopause, S.A.N.E., and pre-puberty). Starter unit includes torso, normal genital pad, normal pelvic organ block with vagina and rectum, abdominal gel pad, fabric abdominal pad, abdominal overlay skin, seven uterus/cervix pieces (normal/normal with discharge option, retroverted/cervicitis, cancer/cancer, transparent IUD trainer, post-menopause/herpes, fibroids/polyp, early pregnancy), five detachable ovaries (normal, polycystic, small cyst, large adnexal mass), bladder insert, pelvic organ prolapse insert, baby powder, Injury Shades Makeup Wheel, Primary Colors Makeup Wheel blood mix, hydroxyethyl cellulose thickener, syringe, lubricant, instruction manual, and hard carry case.
Ripple Tank
Description :-
Transparent acrylic plastic ripple tank, supported in a sturdy plastic frame which has recesses to hold four legs with leveling feet.
The tank edges are shaped to minimize undesired reflections.
Tank has a drain hole closed by a rubber stopper.
With two light alloy uprights to carry a horizontal rippler support rod which is adjustable for height.
The ripple assembly, elastically suspended from the support rod, consists of a 4 – 6 V DC motor mounted on a wooden beam.
The motor has an eccentric weight which causes the beam to oscillate.
Two point sources are provided by two plastic spheres, each mounted on a right angle rod.
A metal rod is fixed centrally into a socket in one short side of the frame to afford support to the illuminant.
Overall size of the tank 580 x 500 x 80 mm, window area 370 x 280 mm, height of tank above bench level (with legs attached) approx. 375 mm.
Complete with following accessories :-
1. Two straight obstacles of aluminium alloy length 130 mm.
2. One straight obstacle length 40 mm.
3. One curved reflector radius 200 mm.
4. One trapezoidal plastic plate for refraction.
5. One wood hand wave roller.
6. One water dropper.
7. One pkt. rubber bands.
8. One foam plastic sponge.
9.One illuminant with a 12 V, 24 W lamp mounted in a lamp house and provided with a long supporting rod.
Three Step Inductor
Description
This three step inductor consists of a coil of enamelled copper wire wound over an insulated spool. The coil consists of 4 layers of 200 turns each. The tappings at 200, 400 and 800 turns are brought out at 4 mm sockets. The output inductances at these tappings are as follows. No. of turns Resistance 200, Inductor 0.3 mH, Resistance 0.6Ω No. of turns Resistance 400, Inductor 1.2 mH, Resistance 1.2Ω No. of turns Resistance 800, Inductor 5.0 mH, Resistance 2.6Ω. One can easily change the inductor value of the instrument on just inserting a soft iron core inside the bobbin
Botany
Algae Fungki, Set of 20 slides
Angiospermic Families, Set of 15 slides
Bacteria, Set of 20 slides
Bacteria, Algae & Fungi, Set of 30 slides
Botany, Set of 30 slides
Bryo & Pteridophyta, Set of 20 slides
Cell Structure, Set of 20 slides
Dispersal of Seeds, Set of 20 slides Fern, Set of 10 slides
Fruits, Set of 20 slides
Germination of Seeds, Set of 20 slides
Higher Plants, Set of 20 slides
Inflorescence, Set of 20 slides
Insectivorous & Parasitic Plants, Set of 20 slides
