XTEMOS ELEMENT
AJAX PRODUCTS TABS
Heat Transfer Activity
Pinhole Camera Kit
Charle’s Law Apparatus
Description
To determine co-efficient of expansion of a gas at constant pressure. A glass U-tube with a bulb and stopcock at one end, the other limb being open. An outlet tube from the bottom of the U tube passes through a rubber bung and has a stopcock at the end. The stem below the bulb is graduated 3 x 0.1 ml. An inlet tube with a mohr clip also passes through the bung. A glass water jacket encloses the U tube. All glass parts made of borosilicate glass requires only 20 ml mercury, which is not included.XTEMOS ELEMENT
AJAX PRODUCTS TABS SIMPLE
Digital Stroboscope
Description :-
Stroboscopic flashes are triggered by either the internal oscillator or by external pulses which may be connected to the two 4mm sockets mounted on the rear panel of the instrument. Example of the many applications of this unit are to be found in motion analysis multi exposures photography, examination of moving parts and measurement of rotational speed.
Specifications:-
Input Volts : 220V AC, 50 Hz
Flash Rate: 0- 9999 Flashes per minute.
Resolution : 1
Display: 7 Segment LED (4 nos.)
Insect Showcase Cabinet (Large)
Description
Provided with 53x45x9cm size drawer for keeping insects. Drawer of MDF with MDF sheet bottom and removable glass top is lined with 8mm thick EVA sheet and is glazed white from inside. Strips with provision for insecticide fitted inside drawer. Glass top frame designed to make box air-tight and pest proof. Fitted with index card holder and puller knobs. Nicely polished. Cabinet frame of plyboard with index card holder and puller knobs. nicely polished. Cabinet frame of plyboard with melamine lamination. Hinged door is provided with lock and handle and is lined with velvet. Insect Showcase Cabinet (Large) with 12 drawers Insect Showcase Cabinet (Large) with 24 drawers
Grease Spot Photometer
Cooling System Of An Automobile
In this model the working of a cooling system of a car is shown with the help of actual parts assembled on a metal stand. All the necessary parts of a cooling system of a car are shown in actual working form. This model helps the student to understand the working of the cooling system of a car very easily. It is specially made dissectible for demonstration purposes.
XTEMOS ELEMENT
AJAX PRODUCTS TABS ALTERNATIVE
Fashion
Hypsometer, Regnault’s
Description
Double walled copper cylinder, 340 x 60 mm, mounted on steam boiler, with thermometer tubule at top and side outlets for manometer and draining. Double walled copper cylinder 34 x 6 cm mounted on steam boiler. Fitted with thermometer, draining tube and glass manometer with rubber bungs. For the determination of the upper fixed points of thermometers andboiling points at barometric pressures other than atmospheric. Double walled copper cylinder 34 x 6 cm height x outer dia. mounted on steam boiler. Fitted with thermometer tubulure at the top, side outlet draining tube and glass manometer mounted in tubulure with rubber bungs.
Suspension Bridge Apparatus
DESCRIPTION:
Cables are frequently used to support loads over large spans such as cable stayed for suspension bridges, cable car systems and stadium roof. They are used extensively for permanent guys on structures such as microwave towers and derricks. They are also used for temporary guys during erection. The only force in a cable is direct tension. They are too flexible to carry any moment. A cable is used to carry concentrated loads, uniformly distributed load along its length and uniformly distributed load along the horizontal span. It takes the shape of a polygon under concentrated loads, a catenary under uniform load along its length (such as its own weight), and a parabola under uniform load along the horizontal span.EXPERIMENT:
• Study the Extension of each spring Balance Left & Right Both. • Study of the effect of a point loadTECHNICAL SPECIFICATION:
• Apparatus Consists of two mild steel cables 0.5cm diameter in cross section and 150cm long, pinned to two supports 90cm apart situated symmetrically. • One of the ends can be converted to a roller by applying a known load at the end with the help of suspended pulley system. • Vertical loads can be applied at various points along the span of the beam. • A dial gauge with 25mm travel (with a magnetic base) is to be supplied with the apparatus complete with a supporting stand and a set of weights.
Main Voltage Coils, For Demountable Transformer
DC Network Analyzer
Specification
• Here we provide the bi-polar Transmission Line. • Simulated long, medium & short distribution lines selectable by patching in various length of DC Transmission line • Two no of bi-polar DC generator sources with ON/OFF control and voltage regulator potentiometer. - Two wire or Three wire Transmission Line operated in +12V DC - Each DC generator are independently control by potentiometer. • 2 digital voltmeters and ammeters provided in the input side and 2 digital volt meters and ammeters are provided in the output side • of transmission line to read the input & output parameters of transmission line. • One no of microcontroller based measuring system provide to read the input and output parameters. • 4 nos of digital ammeters provided to read the load current • 4 nos of resistive load and 4 nos of lamp loads are provided to load the transmission line.XTEMOS ELEMENT
AJAX PRODUCTS TABS ARROWS PAGINATION
Metacentric Height Apparatus
DESCRIPTION:-
A pontoon is allowed to float in a small tank having a transparent side. Removable steel strips placed in the model for the purpose of changing the weight of the model. Displacement of weight is measured with the help of a scale. By means of a pendulum (consisting of a weight suspended to a long pointer) the angle of tilt can be measured on a graduated arc. For tilting the ship model, a cross bar with two movable hangers is fixed on the model. Pendulum and graduated arc are suitably fixed at the center of the cross bar. A set of weights is supplied with the apparatus.EXPERIMENTS:-
Ø Determination of the Metacentric height and position of the Metacentric height with angle of heel of ship model.TECHNICAL SPECIFICATION: –
Ø Pontoon : Size 300 x 150 mm (Approx.) with a Horizontal Guide Bar for aliding weight. Ø Material : Stainless Steel Pontoon Ø Water Tank : Size 600 x 400 x 400 mm (Approx.) Ø Front Window of Tank : made of Glass/Perspex Ø A set of weights is supplied with the apparatus. Ø The whole Set-up is well designed and arranged in a good quality painted Structure
Surber Stream Bottom Sampler
Cross Staff
Description
The Cross-Staff was used at sea from the beginning of the 16th century until the first half of the 18th century. It was used to measure the sun's altitude, especially at the meridian passage. With the knowledge of the sun's declination, the mariner could then obtain his latitude. The staff is original, with the inscription. The cross pieces are replicas. Different cross pieces were used depending on the altitude. A different scale is on each side of the staff.
XTEMOS ELEMENT
AJAX PRODUCTS TABS WITH ICONS
Separating Throttling Calorimeter
AIM
To find out dryness fraction of steam by combined separating and throttling calorimeter.
PRODUCT DETAILS
The steam passing out from separating calorimeter may still contain some water vapour , in it . in other words it may not be absolutely dry . again , in a throttling calorimeter steam after passing through the throttle valve must be superheated or at least dry saturated . this limits the extent of dryness fraction that can be reliably measured , depend up on the pressure of steam in the main steam pipe . if a sample of steam, which may be still wet after passing through the throttle valve i.e it will not be superheated . thus under this condition the throttling calorimeter fails to enable us in determining the value of dryness fraction of steam . to overcome this difficulties we make use of separating and throttling calorimeter . first the steam is passed through separating calorimeter where itlosses most of it’s moisture and becomes comparatively drier, it is than passed through the throttling calorimeter where super heating takes place with out changr of total heat . the temperature and pressure of steam after throttling are measured by using a thermometer and manometer respectively.DESCRIPTION
The set up consist of a separating and throttling calorimeter . a steam generator is provided at the base of the apparatus . a thermostat knob is provided at the front of apparatus to control the temperature inside the steam generator . steam from steam generator is passed from separating calorimeter where most of the water partical get separated from steam and then passed to throttling calorimeter where steam get superheated . after that superheated steam passed through heat exchanger to condense the steam.SAPARATING CALORIMETER
It consist of two concentric chamber , the inner chamber ,and the outer chamber . which communicates with each other through an opening at the top. As the steam discharge through the metal baskets ,which has a large number of holes , the water partical due to there heavier momentum get separated from the steam and collected in the chamber. The comparatively dry steam in the inner chamber moves up and than down aging through the annular space between the two chambers and enters the throttling calorimeter .THROTTLING CALORIMETER
It consist a narrow throat . pressure and temperature are measured by manometer and thermometer . the steam after throttling process passed through the heat exchanger and condensate is collected .UTILITIES REQURIED
1.WATER SUPPLY 3 lit/min (approx) 2.Drain 3.Electric supply : 1phase , 220 V A.C , 2Amp. 4.Steam table for calculation 5.Space required : 1.0 m X 1.0 m
Autoclave, Triple Wall, Vertical, High Pressure, Nut Locking
Specification
Triple Wall, double chamber Autoclave. The lid, ring, inner chamber, middle chamber and outer wall are made of stainless steel. The instrument is absolutely leak proof. Equipped with pressure gauze, safety valve, double safety valve, steam release valve, rubber gasket, mild steel legs for Autoclave. The autoclave can hold the in between 5psi to 20 psi. Autoclave, Triple Wall, Vertical, High Pressure, Nut Locking.| Capacity (Lt.) | Size | |
|---|---|---|
| 40 litres | (12” x 22”) | |
| 60 litres | (14” x 25”) | |
| 75 litres | (16” x 24”) | |
| 95 litres | (18” x 24”) | |
| 180 litres | (22” x 30”) |
XTEMOS ELEMENT
AJAX PRODUCTS TABS LOAD MORE PAGINATION
SILICA CRUCIBLE WITHOUT LID
PRODUCT DESCRIPTION
- Crucible is glazed inside and outside.
- Highly resistant to alkalis and hot temperatures
- 50ml capacity
- Outside diameter 55mm, 42mm height
- No lid includedSilica crucible is glazed inside and outside. Highly resistant to alkalis and hot temperature SIZES ARE: 15ML 25ML 50ML 80ML 100ML 150ML
SILICA CRUCIBLE TALL FORM Without Lid, Translucent
XTEMOS ELEMENT
AJAX PRODUCTS TABS CAROUSEL
Car Chassis Front Wheel Drive Actual Cut Section
Car Chassis Rear Wheel Drive Actual Cut Section – Motorised
4 Stroke 4 Cylinder Petrol Engine With Clutch, Gear Box, Propeller Shaft, & Rear Axle Assembly With Differential Gear
The chassis of the four stroke four cylinder engine cut section model. The cut section model is constructed such that all the following systems can be demonstrated in working conditions.
ENGINE:
Maximum parts and accessories of an engine like cylinders, cylinder head, inlet and Exhaust manifolds, FIP, injectors, self-starter, alternator, water pump, radiator, etc., are sectioned to show the internal constructional details. The complete sectioned model is coupled with FHP 220/230V A.C single phase motor through a Reduction drive unit.TRANSMISSION SYSTEM:
This system consists of a Clutch and four speed gearbox assembly, the casing of which is suitably cut to demonstrate its operation. The gearbox is coupled to Differential gear box with propeller shaft and the different coupling used for this transmission can be demonstrated. The Differential gear box is also cut so as to clearly to demonstrate its complete operating principle. The gear shifting including the forward and reverse gear operation can be clearly shown. The speed variation and the rotation of the Differential gear box can be seen while gear shifting. By running the motor connected to the engine assembly the entire system with gear box, rear axle etc. can be demonstrated in running. FUEL SYSTEM: The Fuel tank is cut to expose the mounting of the level sensor and the position of Fuel section. The system is complete with mechanical Fuel pump. EXHAUST SYSTEM: It consists of Exhaust Manifold and silencer in cut section to explain internal construction. LUBRICATION SYSTEM: It consists of the engine Lubrication system along with the Lubrication oil pump is suitably sectioned. SUSPENSION SYSTEM: This will explain both the Hydraulic Suspension systems at the front and the leaf spring Suspension at the Rear. One of the hydraulic arrangements of Suspension mechanism is highlighted (with shock absorbers) and explained cut sectionally.BRAKING SYSTEM:
The Hydraulic or Air circuit Brakes. The movement of the Brake Shoes on operating the brake pedals can be seen in the area where the Brake drum is cut. The front and rear brakes will be operational. STEERING MECHANISM: The can be seen and included in the Steering wheel. Steering gear box and coupling of the same to the wheels will be shown by rotating the steering wheel, the operation of the steering system can be demonstrated. The entire system will be mounted on the chassis, and suitable mounting option with caster wheels will be provided for easy movability.
Plane Table
Description
The Plane Table Surveying Instruments include standard accessories like Trough Compass, Spirit level, Canvas cover, Plumbing Fork etc., and is also with a fitted tripod. Uses of Plane Table in Engineering Surveys: • Maps preparation • Recording topography Accessories included in Plane Table Surveying Instruments: • Plane Table Board 750 x 600 mm, thickness 22mm & 16mm • Carrying Bag for Board • Teak wood Polished Stand • Stand Rigid Brass Head & Plate, • Magnet Trough compass brass • Spirit Level brass • Sight van 24" • Plumbing Fork • Plumb Bob
Earth, Neutral And Live Board Demonstration
Description
This apparatus is an effective demonstration of how the earth wire and fuse act together to protect both the user and the appliance. When the appliance is connected correctly and the LEDs in the appliance will illuminate to show the appliance is working. A fault is then demonstrated by swapping the live wire from inside the appliance to the case to show either the fuse melts (protecting the user and appliance) or in the case of no earth wire, the LEDs illuminate to indicate the passage of current through the person to ground. The fuse is easily visible and can be seen to ‘blow’ when a fault occurs.The unit is supplied with 10 m of fuse wire and full instructions. A 12 V DC power supply is required. Connections are made via 4 mm shrouded sockets.
Basic Electricity Kit
Description
This economical kit consists of various components, which help students explore many electrical and electronic concepts. Supplied with instruction manual. Kit consists of: Cell Holder (12), Bulb Holder, MES, Mounted on Base (20), Push Key (8), Two Way Switch (4), Universal Clip (4), Electrode Holder (4), Variable Resistance (4), Bulbs, MES (40), Connecting Lead, 4mm, 10cm, Red (12), Connecting Lead, 4mm, 10cm, Black (12), Connecting Lead, 4mm, 25cm, Red (4), Connecting Lead, 4mm, 25cm, Black (4), Crocodile Clips (8), Carbon Rod (12), Soft Iron Rod (8), Silicon Diode (4), Resistance, Fixed (4), Copper Foil Sheet, 150×150mm (1), Copper Wire, Bare, 20SWG (1 Reel), Copper Wire, Insulated, 50m (1 Reel), Eureka Wire, 34SWG (50gm), Steel Wool (1 Pack).
Horizontal Laminar Air Flow
Specifications
We deal in of horizontal laminar air flow that finds it applications in various hospitals, electronic industry and others. We use high grade component and quality raw material that is tested on various quality parameters and ensure smooth functionality. Direction of flow: Horizontal. Cleanliness: CLASS 100. Velocity: 90 FPM + / -20%. Hepa Filter: Size and QTY. will depend on the Size selected. Particle retention: Above 0. 3 micron. Blower Assembly: 1 / 3 HP, 1440 RPM. Noise level: 65 decibel + / -5%. Rate of air flow: 0. 40 to 0. 75 M / Sec. (90 FPM). Vibration level: < 2. 5 micron.Sizes mm.
60x60x60 90x60x60 120x60x60
