XTEMOS ELEMENT
AJAX PRODUCTS TABS
Automatic Gear Box Actual Cut Section
Automatic Gear Box – Actual Cut Section
The working of automatic gear box is shown with the help of actual parts assembled on square iron pipe frame. All the necessary parts of automatic gear box are shown in actual working form. This model helps the student to understand the working of the automatic gear box very easily. It is specially made dissectible for demonstration purposes.
Three Step Inductor
Description
This three step inductor consists of a coil of enamelled copper wire wound over an insulated spool. The coil consists of 4 layers of 200 turns each. The tappings at 200, 400 and 800 turns are brought out at 4 mm sockets. The output inductances at these tappings are as follows. No. of turns Resistance 200, Inductor 0.3 mH, Resistance 0.6Ω No. of turns Resistance 400, Inductor 1.2 mH, Resistance 1.2Ω No. of turns Resistance 800, Inductor 5.0 mH, Resistance 2.6Ω. One can easily change the inductor value of the instrument on just inserting a soft iron core inside the bobbin
Concentric Tube Heat Exchanger
(A)Plain Tube ( Water To Water ):
The apparatus consists of two concentric tubes. Inner tube consists of copper tube through which hot water flows. While the outer tube consists of GI pipe through which cold water flows. The arrangement enables the parallel and counter flow of the cold water. The inlet and outlet temperatures and the flow measurement enable to find out the heat exchanged LMTD, and effectiveness of the equipment.
Specifications:
1.Inner copper tube I.D, 12.7mm. and outer G. I. Pipe I. D. 15mm. approx. and 1.5m. length. 2.Thermometers – 4 nos. 3.Measuring flask – 1 Lit. capacity. 4.Geyser-3 kW. Single phase.Services required
1.220v, 15A, stabilized single-phase AC supply. 2.Floor area – 3m x I m x 1 m height. (B) Finned Tube ( Water To Air ): The apparatus consists of two concentric tubes. Inner tube consists of copper tube through which hot water flows. It is finned at its outer diameter to increase the heat transfer surface. While the outer tube consists of GI pipe through which cold air flows. The arrangement enables the parallel and counter flow of the air. The inlet and outlet temperatures and the flow measurement enable to find out the heat exchanged LMTD, and effectiveness of the equipment.Specifications:
1.Inner copper tube I.D. 12.7mm. and outer G. I. Pipe I. D. 25mm. approx. and 1m. length. 2.Thermometers – 4 nos. 3.Orifice meter along with manometer. 4.Measuring flask – 1 Lit. Capacity. 5.Geyser-3 kW. Single phase.Services Required
1.220v, 15A, stabilized single-phase AC supply. 2.Floor area – 3m x 1m x 1m height.XTEMOS ELEMENT
AJAX PRODUCTS TABS SIMPLE
Round Bottom Centrifuge Tube
Avail from us, a flawless variety of Round Bottom Centrifuge Tube , which is popular for its better quality and precise engineering.
Being one of the chief Exporter and Trader in this industry, the company provides Round Bottom Centrifuge Tube at the most competitive prices.
| Particulars | Pack (Pcs) | |
|---|---|---|
| Centrifuge Tube Round Bottom 16 ml (P.P) | 50 | |
| Centrifuge Tube Round Bottom 50 ml (P.P) | 50 | |
| Centrifuge Tube Round Bottom 16 ml (P.C) | 50 | |
| Centrifuge Tube Round Bottom 50 ml (P.C) | 50 | |
| Cap for 16 ml Centrifuge Tube Round Bottom | 100 | |
| Cap for 50 ml Centrifuge Tube Round Bottom | 100 | |
| Oak Ridge Centrifuge Tubes 30 ml | 12 | |
| Oak Ridge Centrifuge Tubes 50 ml | 12 | |
| Oak Ridge Centrifuge Tubes 100 ml | 12 |
Human Eye, 3 Times Enlarged
Laboratory Spatula
Acquire from us high quality Laboratory Spatula at affordable price range.
Moulded in Polypropylene, Spatula consists of a spoon on one side while the other end is a flat construction with a knife edge.
This is helpful in breaking up crystals of different salts while the spoon is used to draw salts from the containers.
| Particulars | Pack (Pcs) | |
|---|---|---|
| Spatula 150 mm | 12 | |
| Spatula 200 mm | 12 |
Electromagnetic Field Demonstrator
Description
This apparatus demonstrates the magnetic field patterns associated with the different shapes of current carrying conductors. Comprises three conductors, each of different shape/configuration – straight rectangular, circular loop and solenoid all mounted on a plastic base. Each configuration is provided with a pair of 4 mm sockets to connect them to a low voltage DC power source, with output current not exceeding 5A With the included iron filings and 8 magnetic compasses, you can investigate the associated field and flux patterns.XTEMOS ELEMENT
AJAX PRODUCTS TABS ALTERNATIVE
Fashion
Placentation
Human molar Teeth
Sterling Engine Working Model
The Stirling engine was invented by Robert Stirling, a Scottish minister, in 1816. A Stirling engine is a heat engine that operates by cyclic compression and expansion of air or other gas, the working fluid, at different temperature levels such that there is a net conversion of heat energy to mechanical work.
XTEMOS ELEMENT
AJAX PRODUCTS TABS ARROWS PAGINATION
Electrical Power Steering System Actual Working
Electrical Power Steering System – Actual Working
The working of steering system is shown with the help of actual parts assembled on square iron pipe frame. All the necessary parts of steering system are shown in actual working form. This model helps the student to understand the working of the steering system very easily. It is specially made dissectible for demonstration purposes.
XTEMOS ELEMENT
AJAX PRODUCTS TABS WITH ICONS
Direction of Current
Multi Functional I.V. Training Arm
Description
The I.V. Injection Arm P50/1 made of silicone, is unique in quality and design and allows realistic training to teach competence to medical staff. It is also very suitable for group instruction because of its high quality, stain resistance and easy-to-clean soft material.It is ideal for practicing the following:
Correct puncture of peripheral veins for blood sampling. The following veins can be punctured: basilica vein, cephalic vein, median cubital vein, dorsal venous rete of hand Intravenous injections Positioning of a butterfly catheterDelivered in deluxe storage carton with:
1 injection arm with already mounted tubing system 1 infusion bottle 1 stand 1 bottle of artificial blood concentrate(250ml) 1 plastic cup 1 disposable syringe and 2 injection cannulas (recommended cannula size: 20 and 21 gauge) 2 tubing systems as replacement parts 1 container of talcum powder
Vacuum Delivery Model
Description
The model basing on the mechanism of normal labor shows the cardinal movements of engagement. Descent-flection-internal rotation of the head-extension-retitution-external rotation of the head-internal rotation of the shoulders at accouchement. Suitable for teaching the mechanism of normal labor in medical colleges and nursing schools.XTEMOS ELEMENT
AJAX PRODUCTS TABS LOAD MORE PAGINATION
SILICA CRUCIBLE WITHOUT LID
PRODUCT DESCRIPTION
- Crucible is glazed inside and outside.
- Highly resistant to alkalis and hot temperatures
- 50ml capacity
- Outside diameter 55mm, 42mm height
- No lid includedSilica crucible is glazed inside and outside. Highly resistant to alkalis and hot temperature SIZES ARE: 15ML 25ML 50ML 80ML 100ML 150ML
SILICA CRUCIBLE TALL FORM Without Lid, Translucent
XTEMOS ELEMENT
AJAX PRODUCTS TABS CAROUSEL
Domestic Refrigerator Actual Cut Section
This model will be made out of original parts. The model will be suitably sectioned to demonstrate the internal construction details showing the minute information, and working of the same, the model will be suitably painted and mounted on a metal or wooden base & supplied with key card & very interesting literature regarding working of the same.
‘Gravity’ By Free Fall Apparatus
Consists of an electromagnet housed in a plastic moulded case with connections for an external timer, with a heavy steel sphere, and a platform unit.
For determination of 'g' (the gravitational acceleration) by free fall method.
The apparatus consists of an electromagnet which is housed in a plastic moulded case with 4 mm socket connections provided to energize the magnet and another pair of sockets for connection to a timer in use.
To perform the experiment, an electromagnet is energized and a metal sphere is attached.
As soon as the power to the electromagnet is switched off the sphere falls and the unit activates the timer.
When the sphere hits the platform, which is connected to a micro switch, the timer stops and the time of fall can be determined.
For use with compatible timer (product code LBTM).
Unit conveniently attaches to all commonly used stands (stand not supplied, see Stand & Rod Assembly - Value Pack STD-RD).
